Research

Paper · MFC

Enhancing electricity generation using fungal laccase-based microbial fuel cell

  • MFC
  • Dual Chamber
01

Summary

What the paper reports, in its own words.

3D Interactive ModelAI Enhanced· 72%Substrate ·real wastewaterPower GenerationBioremediation

Abstract

Microbial fuel cells (MFCs) are very important source to obtain green electricity and also for decontamination of waste water. Bioelectricity yield from biofuel cells is still needed for maximizing. Microbial laccases, especially those produced by fungi, are currently considered to be one of the most promising biocatalyst for bioelectricity production and also purification of water from the different pollutant, especially phenolic compounds. In the present work, different electrolyte solutions used in anode and cathode chambers to evaluate efficiency of each to produce voltage & current and also to prove that using economical electrolytes, which were agro-industrial waste called el-ghasheem at anode and only tap water at cathode, achieve good results in comparison with other commonly used electrolytes which were glucose, sodium nitrate, mono-potassium phosphate, di-potassium phosphate, ammonium chloride and magnesium sulfate. The use of El-ghasheem in the economic MFC showed power improvement results when fungal laccase, produced from Monodictys castaneae fungus, had been used as cathodic reaction catalyst to increase voltage production from 0.466±0.003 V to 0.807±0.002 V and current from 0.025±0.003 A to 0.09±0.003 A at 37 °C, anolyte pH 6 and catholyte pH 5 for 10 days incubation period. It was noticed that this laccase enzyme had the 98.38±0.264 % phenol removal activity from anode chamber through indirect effect and 99.69±0.276 % phenol removal activity from cathode chamber through direct effect when El-ghasheem was used as the organic fuel at the anode side. In this study using unstudied agro-industrial waste, Electricity was produced by the new fungal laccase which showed the high performance in electricity production enhancement and also phenol compounds removal through low cost MFC.

AI summary

72% confidence

This paper demonstrates enhancement of electricity generation in a two-chamber microbial fuel cell (MFC) using fungal laccase (from Monodictys castaneae) as a cathode biocatalyst, combined with agro-industrial waste (el-ghasheem) as anode electrolyte. Laccase increased voltage 73% (0.466→0.807 V) and current 260% (0.025→0.09 A) at optimized conditions (37°C, anolyte pH 6, catholyte pH 5, 10 days). Phenol removal reached 98.4% at anode and 99.7% at cathode. The work prioritizes cost reduction and dual function (power + remediation) over mechanistic insight into nitrogen cycling or electrochemical kinetics.

Key insights

  • Threshold Catholyte pH optimum shifts from 7 (control MFC: 0.466 V) to pH 5 (laccase MFC: 0.807 V), a 1.73× voltage gain at lower pH

    So what. If deploying laccase cathodes, operate at pH 5 not pH 7; this is a critical operating window shift that contradicts standard MFC practice

  • Threshold Laccase maintains activity for 14 days but peaks at day 10–12 (0.807 V on day 10), then declines gradually

    So what. Plan batch operation cycles around day 10 harvest; do not assume continuous stable output beyond 12 days

  • Threshold Temperature optimum is 37°C for both control and laccase MFC; performance drops at 42°C and 20°C

    So what. Maintain strict temperature control at 37°C; even 5°C deviation reduces output; this is a narrow operating window

  • Trade-off Anolyte pH 6 is optimal for control MFC (0.466 V, 0.025 A) but paper does not test anolyte pH with laccase cathode

    So what. Anolyte pH 6 + catholyte pH 5 combination is untested; verify this pairing does not create pH gradient stress or ion transport issues

  • Mechanism Phenol removal is 98.4% at anode (indirect, via microbial degradation) but 99.7% at cathode (direct, via laccase), showing compartmentalization of remediation

    So what. Laccase acts primarily as a direct oxidizer at cathode; anode phenol removal is microbial, not enzymatic—do not assume enzyme catalyzes both chambers

Contradictions3

Tensions the paper itself points to. Each side quotes the passage it comes from.

  • Within the paper Laccase activity stability claim conflicts with observed decline after day 12

    One side

    Laccase 'keep its activity for all of 14 days' (text, Optimization section)

    “laccase keep its activity for all of 14 days, the complete incubation period”
    Other side

    Laccase 'achieved the maximum stimulation for bioelectricity at the range day 10-12, after that its activity decreased slightly and gradually' (text, same section)

    “achieved the maximum stimulation for bioelectricity at the range day 10-12, after that its activity decreased slightly and gradually”

    Authors’ reading. Authors distinguish between 'keeping activity' (remaining present) and 'peak performance' (day 10–12); activity persists but declines post-day 12, so the statements are compatible if 'activity' means presence not efficacy

  • Within the paper Optimal catholyte pH differs between control and laccase MFC, but paper does not explain mechanism

    One side

    Control MFC optimal at pH 7: '0.466±0.003 V and 0.025±0.003 A' (Figure 8, text)

    “catholyte pH7 achieved the highest voltage and current, 0.466±0.003 V and 0.025±0.003 A for control MFC3 (without laccase)”
    Other side

    Laccase MFC optimal at pH 5: '0.807±0.002 V and 0.09±0.003 A' (Figure 8, text)

    “catholyte pH 5 was the optimum pH for laccase activity and achieved the highest voltage and current, 0.807±0.002 V and 0.09±0.003 A”

    Authors’ reading. Authors note that pH affects enzyme properties (activity, stability, solubility) and cite Nernst equation effects (~60 mV per pH unit), but do not quantify why laccase prefers pH 5 over pH 7 or test intermediate pH values with laccase

  • Within the paper MFC3 with el-ghasheem outperforms MFC2 with standard nutrients, contradicting expectation that defined media optimize performance

    One side

    MFC3 (el-ghasheem + tap water) achieves 0.43 V; MFC2 (standard nutrients) achieves 0.36 V (Figure 2)

    “MFC3 achieved the best voltage with 0.43±0.026 V in comparison to 0.36±0.015 V using MFC2”
    Other side

    MFC2 uses 'commonly used electrolytes which were glucose, sodium nitrate, mono-potassium phosphate, di-potassium phosphate, ammonium chloride and magnesium sulfate' (Abstract)

    “using economical electrolytes, which were agro-industrial waste called el-ghasheem at anode and only tap water at cathode, achieve good results in comparison with other commonly used electrolytes”

    Authors’ reading. Authors attribute success to el-ghasheem's natural nutrient profile and microbial consortium from soil extract; they frame this as cost advantage, not mechanistic superiority, and do not analyze el-ghasheem composition

Opportunity areas6

Specific gaps in this paper, with an experiment that would close each.

  • High No test of anolyte pH with laccase cathode; only anolyte pH 6 used in laccase experiments

    Control MFC shows anolyte pH 6 optimal (0.466 V at pH 6 vs 0.25 V at pH 4), but laccase experiments fix anolyte pH 6 and vary only catholyte pH. Interaction between anolyte and catholyte pH is not explored.

    Try. Test anolyte pH 4, 5, 6, 7 with laccase cathode at fixed catholyte pH 5 and 37°C; measure voltage, current, and phenol removal to identify any synergy or antagonism

  • Medium No measurement of current density or power density normalized to electrode area; only absolute current and power reported

    Paper states 'power and current per surface area of the anode (6 cm²) was used to calculate the power and current density' but no density values are reported in results or figures. Comparison with literature requires normalization.

    Try. Recalculate and report current density (mA/cm²) and power density (mW/cm²) for all conditions; compare to laccase MFC benchmarks (e.g., Sato et al. 249.67 mV OCV cited in text)

  • Medium No test of external load resistance; only 1 kΩ used throughout

    Paper states '1kOhm resistance was used as external load' but does not vary load to find maximum power point or internal resistance. Optimal load for laccase cathode may differ from control.

    Try. Sweep external load from 100 Ω to 10 kΩ at 37°C, anolyte pH 6, catholyte pH 5 with and without laccase; plot power vs. load to identify maximum power point and internal resistance

  • Medium No characterization of el-ghasheem composition; phenol content assumed but not quantified beyond initial measurement

    El-ghasheem is described as 'agro-industrial waste called el-ghasheem which is produced from boiling of Sugarcane juice' but no proximate analysis, C/N ratio, or full phenolic profile provided. Reproducibility and scalability limited.

    Try. Analyze el-ghasheem for total organic carbon, total nitrogen, C/N ratio, phenolic compound profile (HPLC), and microbial community (16S rRNA) to enable replication and optimization

  • Medium No measurement of dissolved oxygen, pH gradient, or ion transport across salt bridge during operation

    Paper mentions pH gradients cause ~60 mV loss per unit (Nernst equation) but does not measure actual pH drift in anode or cathode during 10-day run. Catholyte pH 5 vs anolyte pH 6 may create gradient stress.

    Try. Monitor anode and cathode pH, dissolved oxygen, and conductivity daily during 10-day laccase MFC run at 37°C; correlate pH drift with voltage decline post-day 12

  • Low No test of laccase enzyme concentration or activity threshold; only 3 U/ml used

    Paper states 'crude enzymes with 3U/ml activity' but does not vary enzyme concentration to find saturation or minimum effective dose. Cost-benefit of enzyme loading not explored.

    Try. Test laccase activity from 0.5 to 10 U/ml at 37°C, anolyte pH 6, catholyte pH 5; measure voltage, current, and phenol removal to identify cost-optimal enzyme loading

Generated by MESSAI extraction pipeline · review against source PDF

02

Extracted values

Every value pulled from the paper, with its source, so each number can be checked against the text.

n = 95 extracted values

Select a citation to see the quote, page and confidence behind a value.

66 of 91 extracted rows modelable

  • 8 not canonicalised (no canonical slug)
  • 15 no SI value
  • 2 contradicts other papers
ParameterValueUnitConfidenceSourceNotesModelable
Voltage0.466V95%
llm
conclusion
Temperature37°C95%
llm
pH6-95%
llm
Substrateglucose—80%
llm
Open Circuit Voltage0.466V98%
extracted
"It was noticed that this laccase enzyme had the 98.38±0.264 % phenol removal act…" · T=37°C, pH(an)=6, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batchModelable
Open Circuit Voltage0.805V98%
extracted
"In this study using laccase at the cathode of MFC3 elevated the resulted voltage…" · T=37°C, pH(an)=7, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batchModelable
Peak voltage v0.466V98%
extracted
T=37°C, pH(an)=6, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batchModelable
Power Density0.012W98%
extracted
"The power produced was calculated using the following formula: P = I x V where P…" · T=37°C, pH(an)=6, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batchExcluded: no SI value
Current Density0.025A98%
extracted
"The power and current per surface area of the anode (6 cm2) was used to calculat…" · T=37°C, pH(an)=6, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batchExcluded: no SI value
Power Density0.064W98%
extracted
"A 68.75% increase in the produced current from 0.025±0.003 A to 0.08±0.002 A and…" · T=37°C, pH(an)=7, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batchExcluded: no SI value
Current Density0.08A98%
extracted
"A 68.75% increase in the produced current from 0.025±0.003 A to 0.08±0.002 A and…" · T=37°C, pH(an)=7, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batchExcluded: no SI value
Peak voltage v0.805V98%
extracted
T=37°C, pH(an)=7, substrate=El-ghasheem (agro-industrial waste from sugarcane juice boiling), batchModelable
Current0.09A95%
digital multi-meter
"current from 0.025±0.003 A to 0.09±0.003 A" · T=37°C, pH(an)=5, substrate=El-ghasheem, steady_stateModelable
Electrode Surface Area×26cm²95%
extracted
"The power and current per surface area of the anode (6 cm2) was used to calculat…" · condition_hint=design parameter for anode electrode, electrode_material=graphite rodModelable
Current0.025A95%
digital multi-meter
"current from 0.025±0.003 A to 0.09±0.003 A" · T=37°C, pH(an)=6, substrate=El-ghasheem, steady_stateModelable
Electrode Surface Area×24cm95%
extracted
"One end of the copper wire was attached to 4 cm long and 0.5 cm diameter graphit…" · condition_hint=design parameter for electrode, electrode_material=graphite rodExcluded: no SI value
Current0.025A95%
digital multi-meter
"catholyte pH7 achieved the highest voltage and current, 0.466±0.003 V and 0.025±…" · T=37°C, pH(an)=7, substrate=El-ghasheem, steady_stateModelable
Current0.09A95%
digital multi-meter
"current from 0.025±0.003 to 0.09±0.003 A" · T=37°C, pH(an)=5, substrate=El-ghasheem, steady_stateModelable
Current0.09A95%
digital multi-meter
"catholyte pH 5 was the optimum pH for laccase activity and achieved the highest …" · T=37°C, pH(an)=5, substrate=El-ghasheem, steady_stateModelable
Electrode Diameter×20.5cm95%
extracted
"One end of the copper wire was attached to 4 cm long and 0.5 cm diameter graphit…" · condition_hint=design parameter for electrode, electrode_material=graphite rodModelable
Current0.08A95%
digital multi-meter
"A 68.75% increase in the produced current from 0.025±0.003 A to 0.08±0.002 A" · T=37°C, pH(an)=6, substrate=El-ghasheem, steady_stateModelable
External Load×21,000Ohm95%
extracted
"1kOhm resistance was used as external load" · condition_hint=design parameter for external circuit, external_resistance_ohm=1000Modelable
Current0.025A95%
digital multi-meter
"This pH achieved the highest voltage, 0.466±0.003 V, and current, 0.025±0.003 A" · T=37°C, pH(an)=6, substrate=El-ghasheem, steady_stateModelable
Peak Current0.08A95%
digital multi-meter
"A 68.75% increase in the produced current from 0.025±0.003 A to 0.08±0.002 A" · T=37°C, pH(an)=6, substrate=El-ghasheem, steady_stateModelable
Peak Current0.09A95%
digital multi-meter
"current from 0.025±0.003 to 0.09±0.003 A" · T=37°C, pH(an)=5, substrate=El-ghasheem, steady_stateModelable
Showing 25 of 77

Methodology

What was the system and how was it run

Methodology

Methodology

Two-chamber H-type MFC with graphite rod electrodes (4 cm × 0.5 cm), salt bridge (lamp wick in 1 M KCl), and 1 kΩ external load. Three MFC designs tested with different electrolytes; best performer (MFC3: el-ghasheem anode + tap water cathode) optimized by varying temperature (20–42°C), anolyte pH (4–7), and catholyte pH (3–8) over 10–14 days at 37°C. Laccase (3 U/ml from Monodictys castaneae) added to cathode; voltage and current measured daily with digital multimeter. Phenol quantified by FeCl₃ colorimetry at 540 nm using guaiacol standard curve.

System configuration

FieldValue
reactor typeMFC
chamber config2-chamber

Operational parameters

FieldValue
p h{"min":5,"max":6,"optimal":6}
temperature{"min":37,"max":37,"optimal":37}
substrate["glucose"]

Operating conditions

23 runs extracted
RunT°CpHanpHcatSubstrate[S]mg/LHRThModeR_extΩV_appVInoculum
baseline3765El-ghasheem (agro-industrial waste containing phenols)——batch———
baseline #23765El-ghasheem (agro-industrial waste containing phenols)——batch———
baseline #33765El-ghasheem (agro-industrial waste containing phenols)——batch———
control_without_laccase3777El-ghasheem (agro-industrial waste containing phenols)——batch———
control_without_laccase #23777El-ghasheem (agro-industrial waste containing phenols)——batch———
control_without_laccase #33777El-ghasheem (agro-industrial waste containing phenols)——batch———
v2-05d474b1538d5315377—El-ghasheem (agro-industrial waste containing phenols)——batch———
v2-141f6ecf42d1e9bd376—El-ghasheem (agro-industrial waste from sugarcane juice boiling)——batch———
v2-3a8eaa60654df296———————1000——
v2-49eb3911c6b140cd377—El-ghasheem——steady_state1000——
v2-4faa6bd8a7188e91377—glucose, El-ghasheem——steady_state1000——
v2-568ce878db11874b377—sodium acetate——steady_state1000——
v2-7e774506c7d77bd9376—El-ghasheem——steady_state1000——
v2-9efe7e198728080f377—El-ghasheem (agro-industrial waste from sugarcane juice boiling)——batch———
v2-aabb8442e7e3e8c7378—El-ghasheem——steady_state1000——
v2-bdc0834e67a8253b207—El-ghasheem——steady_state1000——
v2-c141e56f48ac6555375—El-ghasheem——steady_state1000——
v2-c71809f1bba9d95b287—El-ghasheem——steady_state1000——
v2-cdb8639ff58eb681376—El-ghasheem (agro-industrial waste containing phenols)——batch———
v2-d99195a02ef03c53374—El-ghasheem——steady_state1000——
v2-e5acc20b6edab361———El-ghasheem——startup———
v2-f586e9af22985397——————————
v2-f8a4c73dc9ae083b373—El-ghasheem——steady_state1000——

Pipeline

Raw extractions, artifacts, quality signal

Extraction quality

honesty signal

Calibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.

Parameter completeness

25%

Fraction of expected parameters extracted

Data completeness

50%

Overall extraction coverage across fields

AI confidence

72%

Model self-reported confidence

Mean parameter confidence

90%

Average confidence across PaperParameter rows surfaced above

Last extraction:vpipeline-v2FULL_EXTRACTIONcompleted95 parameters surfaced

review against source PDF before citing · scores 0–1

03

Chart explorer

Move the inputs this paper used and see how the predicted outcome shifts.

04

Explore model

The reactor in 3D, with flow you can switch on and off.

05

AI insights

Contradictions, gaps and opportunities found by comparing this paper with the corpus.

06

Compare similar papers

The nearest papers by system, materials and organisms, with their outcomes side by side.

07

Source PDF

The paper as published.

loading 3D model…

Representative model: Dual-chamber H-cell MFC

Representative dual-chamber H-cell — matched on the paper’s reported configuration, not its exact geometry.

MFC
System
0.81volts
Best result · Voltage
best of 46
95
Extracted values
2024
Year

In this record

Organisms, parameters and materials this paper reports. Each links to its page.

Organisms · 2

  • Monodictys castaneae
  • Monodictys castaneae fungus

Materials · 3

  • El-ghasheem (agro-industrial waste)
  • laccase enzyme
  • Salt Bridge

Keywords

  • Microbial fuel cell
  • Laccase
  • Anode
  • Wastewater
  • Pulp and paper industry
  • Phenol

Cite

Hani Moubasher, Abdelrahman Tammam, Mahmoud Saleh (2024). Enhancing electricity generation using fungal laccase-based microbial fuel cell. Journal of microbiology, biotechnology and food sciences. https://doi.org/10.55251/jmbfs.9703

Open in lab for full controls, parameter editing, and template overlays.

Open in lab