Research

Paper · MES

Efficient Hydrogen Delivery for Microbial Electrosynthesis via 3D-Printed Cathodes

01

Summary

What the paper reports, in its own words.

3D Interactive Model

Abstract

The efficient delivery of electrochemically in situ produced H 2 can be a key advantage of microbial electrosynthesis over traditional gas fermentation. However, the technical details of how to supply large amounts of electric current per volume in a biocompatible manner remain unresolved. Here, we explored for the first time the flexibility of complex 3D-printed custom electrodes to fine tune H 2 delivery during microbial electrosynthesis. Using a model system for H 2 -mediated electromethanogenesis comprised of 3D fabricated carbon aerogel cathodes plated with nickel-molybdenum and Methanococcus maripaludis , we showed that novel 3D-printed cathodes facilitated sustained and efficient electromethanogenesis from electricity and CO 2 at an unprecedented volumetric production rate of 2.2 L CH4 /L catholyte /day and at a coulombic efficiency of 99%. Importantly, our experiments revealed that the efficiency of this process strongly depends on the current density. At identical total current supplied, larger surface area cathodes enabled higher methane production and minimized escape of H 2 . Specifically, low current density (<1 mA/cm 2 ) enabled by high surface area cathodes was found to be critical for fast start-up times of the microbial culture, stable steady state performance, and high coulombic efficiencies. Our data demonstrate that 3D-printing of electrodes presents a promising design tool to mitigate effects of bubble formation and local pH gradients within the boundary layer and, thus, resolve key critical limitations for in situ electron delivery in microbial electrosynthesis.

02

Extracted values

Every value pulled from the paper, with its source, so each number can be checked against the text.

n = 17 extracted values

Select a citation to see the quote, page and confidence behind a value.

6 of 17 extracted rows modelable

  • 1 not canonicalised (no canonical slug)
  • 2 no SI value
  • 4 verifier rejected the value
  • 4 contradicts other papers
ParameterValueUnitConfidenceSourceNotesModelable
Coulombic efficiency×499%90%
extracted
"At 60 mA total current, the reactors with the three highest surface area cathode…" · T=30°C, pH(an)=7, substrate=CO2, steady_stateExcluded: verifier rejected the value
Coulombic efficiency99%90%
extracted
"corresponding to a volumetric methane production rate of 2.2 LCH4 /Lcatholyte/da…" · T=30°C, pH(an)=7, substrate=CO2, steady_stateModelable
Coulombic efficiency97%90%
extracted
"At 0.6 mA/cm2 highly efficient methane production was established only after 145…" · T=30°C, pH(an)=7, substrate=CO2, steady_stateModelable
Coulombic efficiency98%90%
extracted
"At the lowest current density of 0.5 mA/cm2 (high surface area), stable electrom…" · T=30°C, pH(an)=7, substrate=CO2, steady_stateModelable
Coulombic efficiency20%90%
extracted
"resulted in an overall low coulombic efficiency of 20 ± 4% for methane (averaged…" · T=30°C, pH(an)=7, substrate=CO2Excluded: contradicts other papers
Coulombic efficiency12%90%
extracted
"the average coulombic efficiency for methane was only 12 ± 2%" · T=30°C, pH(an)=7, substrate=CO2Excluded: contradicts other papers
Startup Time×27h90%
extracted
"For current densities of 0.5 and 0.6 mA/cm2, highly efficient methane production…" · T=30°C, pH(an)=7, substrate=CO2Modelable
CH₄ Production Rate1other90%
extracted
"Increasing the current to 70 mA led to an increase in methane production rate, e…" · T=30°C, pH(an)=7, substrate=CO2Excluded: no SI value
Startup Time55h90%
extracted
"At a current density of 0.9 mA/cm2, steady state methane production was reached …" · T=30°C, pH(an)=7, substrate=CO2Excluded: contradicts other papers
Startup Time24h90%
extracted
"stable electromethanogenesis was observed within 24 h" · T=30°C, pH(an)=7, substrate=CO2Modelable
Hydrogen in Reactor Off-gas1other90%
extracted
"With increasing current density, steady state operation was delayed and H2 conce…" · T=30°C, pH(an)=7, substrate=CO2Excluded: not canonicalised (no canonical slug)
Startup Time145h90%
extracted
"highly efficient methane production was established only after 145 h" · T=30°C, pH(an)=7, substrate=CO2Excluded: contradicts other papers
CH₄ Production Rate2.2LCH4/Lcatholyte/day90%
extracted
"corresponding to a volumetric methane production rate of 2.2 LCH4 /Lcatholyte/da…" · T=30°C, pH(an)=7, substrate=CO2, steady_stateExcluded: no SI value

Methodology

What was the system and how was it run

Operating conditions

2 runs extracted
RunT°CpHanpHcatSubstrate[S]mg/LHRThModeR_extΩV_appVInoculum
v2-0cd05285734d985a307—CO2——steady_state———
v2-5fdc0b1496fa68b1307—CO2——————

Pipeline

Raw extractions, artifacts, quality signal

Extraction quality

honesty signal

Calibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.

AI confidence

60%

Model self-reported confidence

Mean parameter confidence

90%

Average confidence across PaperParameter rows surfaced above

review against source PDF before citing · scores 0–1

03

Chart explorer

Move the inputs this paper used and see how the predicted outcome shifts.

04

Explore model

The reactor in 3D, with flow you can switch on and off.

05

AI insights

Contradictions, gaps and opportunities found by comparing this paper with the corpus.

06

Compare similar papers

The nearest papers by system, materials and organisms, with their outcomes side by side.

07

Source PDF

The paper as published.

loading 3D model…

Representative model, generic microbial electrochemical system

Representative microbial electrochemical system — matched on the paper’s system type only, not its reactor or geometry.

MES
System
99.0percent
Best result · Coulombic efficiency
best of 9
17
Extracted values
2021
Year

In this record

Organisms, parameters and materials this paper reports. Each links to its page.

Keywords

  • Electrosynthesis
  • Faraday efficiency
  • Cathode
  • Nanotechnology
  • Hydrogen production
  • Electrode

Cite

Frauke Kracke, Jörg S. Deutzmann, Buddhinie Srimali Jayathilake et al. (2021). Efficient Hydrogen Delivery for Microbial Electrosynthesis via 3D-Printed Cathodes. Frontiers in Microbiology. https://doi.org/10.3389/fmicb.2021.696473

PubMed
34413839

Open in lab for full controls, parameter editing, and template overlays.

Open in lab