Paper · MFC
Enhancing the Electricity Generation and Nitrate Removal of Microbial Fuel Cells With a Novel Denitrifying Exoelectrogenic Strain EB-1
Summary
What the paper reports, in its own words.
AI summary
78% confidenceThis paper isolates and characterizes Mycobacterium sp. EB-1, a novel denitrifying exoelectrogen capable of simultaneous anodic denitrification and electricity generation in a two-chamber MFC. The strain achieves 0.84 W/m² power density and removes NO₃⁻-N at 0.66 kg N/m³/d with no inhibition of voltage output despite increasing nitrate (0–200 mg/L NO₃⁻-N). Electron flux analysis reveals that denitrification and anode respiration compete for electrons from acetate, with coulombic efficiency dropping from 83.9% to 6.5% as nitrate rises, indicating electron donor limitation rather than system inhibition.
Key insights
Threshold Voltage output (Vmax) remained stable across NO₃⁻-N concentrations 0–200 mg/L, while cycle duration shortened, proving concurrent denitrification and anode respiration are electron-donor limited, not inhibited.
So what. Operators can tolerate high nitrate loads without voltage collapse if acetate supply is adequate; design for electron donor availability, not nitrate toxicity.
Trade-off Coulombic efficiency (CE) dropped from 83.9 ± 2.7% (no nitrate) to 6.5 ± 2.2% (200 mg/L NO₃⁻-N), while corrected CE (excluding denitrification electrons) remained ~90%, showing denitrification diverts 77% of electrons at high nitrate.
So what. If power recovery is the goal, minimize nitrate or operate at low NO₃⁻-N (<50 mg/L); if nitrogen removal is primary, accept low CE and design for electron flux partitioning.
Performance Nitrite accumulation remained <1 mg/L throughout all tests despite NO₃⁻-N reduction to N₂, indicating complete denitrification pathway without intermediate accumulation.
So what. No need for post-treatment to remove nitrite or ammonia; design can assume complete N₂ production without intermediate trapping.
Mechanism Direct electron transfer (DET) mechanism confirmed by rapid CV recovery (41.2% recovery in 5 min, 92.1% in 10 min after medium replacement) and two redox peaks at −0.21 V and −0.185 V (vs. Ag/AgCl), consistent with outer membrane c-type cytochromes.
So what. Gram-positive Mycobacterium can use DET like gram-negative model organisms; electrode material selection should optimize for c-type cytochrome interaction, not rely on soluble mediators.
Performance Nitrate removal rate of 0.66 ± 0.01 kg N/m³/d (27.7 ± 0.5 mg N/L/h) at 200 mg/L NO₃⁻-N exceeds biocathode MFC rates (0.02–0.43 kg N/m³/d) and matches conventional heterotrophic denitrification (0.08–1.36 kg N/m³/d with carbon).
So what. Anodic denitrification with EB-1 is kinetically competitive with conventional treatment; consider for high-nitrate, low-COD/N wastewater where biocathodes underperform.
Contradictions1
Tensions the paper itself points to. Each side quotes the passage it comes from.
Against prior work Prior work showed nitrate inhibits current generation in denitrifying exoelectrogens, but this strain shows no voltage inhibition.
One sideComamonas denitrificans DX-4 and Calditerrivibrio nitroreducens produced decreased voltage when nitrate was added (Xing et al. 2010, Fu et al. 2013)
“The power output of MFCs with Comamonas denitrificans (Xing et al., 2010) or Calditerrivibrio nitroreducens (Fu et al., 2013) was found to be decreased when nitrate was added to the anode chamber of MFCs”
Other sideMycobacterium sp. EB-1 showed 'maximum voltage output (Vmax) was rarely affected' by NO₃⁻-N up to 200 mg/L
“the maximum voltage output (Vmax) was rarely affected. The concurrent processes of denitrification and anode respiration are thus a limitation of the electron donor rather than an inhibition of the system.”
Authors’ reading. Authors attribute the difference to electron donor limitation vs. inhibition: in prior work, external resistance was lower (100 Ω vs. 1 kΩ here), limiting electron transfer rate and forcing competition; in EB-1, the 1 kΩ resistance allows sufficient electron flux for both pathways without voltage collapse. The domestication process may also have selected for EB-1 strains with higher denitrification enzyme expression.
Opportunity areas6
Specific gaps in this paper, with an experiment that would close each.
High No systematic variation of external resistance (only 1 kΩ tested); prior work (Xing et al. 2010, Fu et al. 2013) used 100 Ω and showed inhibition. Test 100–10,000 Ω to map the operating window where voltage remains stable vs. collapses with increasing NO₃⁻-N.
Authors note that external resistance affects electron transfer rate and competition between pathways, but only one resistance value is used. Figure 6A shows cycle duration shortens with NO₃⁻-N; lower resistance might reveal voltage collapse.
Try. External resistance: 100, 500, 1000, 5000 Ω; NO₃⁻-N: 0, 50, 100, 200 mg/L; measure Vmax, cycle time, CE, and electron flux partitioning.
High No exploration of COD/N ratio trade-off; acetate held constant at 780.5 mg/L COD while NO₃⁻-N varied 0–200 mg/L, giving COD/N ratios of ∞ to 3.9. Critical COD/N for complete denitrification is mentioned (equation 3) but not experimentally validated.
Text states 'low COD/N ratios significantly inhibit current generation' and cites prior work showing no current at low COD/N, but this paper does not test the boundary. Figure 6 shows 82.8% removal at 200 mg/L NO₃⁻-N (COD/N ≈ 3.9), but incomplete removal; the critical threshold is not identified.
Try. COD/N ratio: 2, 3, 4, 5, 7 (acetate fixed, NO₃⁻-N varied); measure voltage, CE, nitrate removal %, and electron flux to identify minimum COD/N for complete denitrification without voltage loss.
Medium Catholyte pH and dissolved oxygen not controlled or reported; only anode chamber conditions detailed. Cathode performance and O₂ reduction kinetics may limit overall MFC performance at high current densities.
Methods state '100 mM sterilized PBS was used as the catholyte' but no pH monitoring or control is mentioned. Figure 3B shows power density curve but not cathode potential or O₂ limitation effects. At 1.9 A/m² current, cathode may become rate-limiting.
Try. Measure cathode potential, dissolved O₂ in catholyte, and pH during operation at 0–200 mg/L NO₃⁻-N; vary catholyte pH (6.5–8.5) and O₂ saturation to assess cathode contribution to voltage loss.
Medium Hydraulic retention time (HRT) not varied; all experiments are batch mode with medium replacement when voltage drops below 20 mV. No continuous-flow or fed-batch operation tested to assess practical treatment rates and stability.
Batch operation with manual replacement is not scalable. Text reports 'average nitrate removal rate of 0.66 kg N/m³/d' but this is calculated from batch data; actual HRT and volumetric throughput are not specified. Cycle duration shortens with NO₃⁻-N (Figure 6A) but implications for continuous operation are unclear.
Try. Continuous-flow operation at HRT 12, 24, 48 h; NO₃⁻-N 50, 100, 200 mg/L; measure steady-state voltage, CE, nitrate removal %, and N₂O production.
Medium N₂O production not measured; only N₂ and NH₄⁺ quantified. Incomplete denitrification to N₂O is a known issue in bioelectrochemical systems and could represent a significant electron loss and environmental concern.
Text states 'nitrate was reduced to nitrogen gas and no ammonium was detected' but N₂O is not mentioned in the analytical methods (Section 'Calculation'). At 200 mg/L NO₃⁻-N, 82.8% removal in 6 h leaves 17.2% unaccounted; N₂O could be a product.
Try. Gas chromatography or membrane inlet mass spectrometry to quantify N₂, N₂O, and NO in headspace at NO₃⁻-N 50, 100, 200 mg/L; correlate N₂O yield with cathode potential and dissolved O₂.
Medium Anode potential not controlled or reported; only external resistance (1 kΩ) and voltage output measured. Anode potential is critical for denitrification enzyme activity and electron transfer kinetics but is not characterized.
Methods describe polarization curves (Figure 3B) but do not report anode potential vs. SHE or Ag/AgCl. CV analysis (Figure 4) uses Ag/AgCl reference but anode potential during batch operation is not provided. This limits reproducibility and mechanistic understanding.
Try. Potentiostat-controlled anode potential: −0.3, −0.2, −0.1, 0 V vs. Ag/AgCl; NO₃⁻-N 0, 100, 200 mg/L; measure current, CE, denitrification rate, and electron flux partitioning.
Generated by MESSAI extraction pipeline · review against source PDF
Extracted values
Every value pulled from the paper, with its source, so each number can be checked against the text.
n = 16 extracted values
Select a citation to see the quote, page and confidence behind a value.
9 of 16 extracted rows modelable
- 6 not canonicalised (no canonical slug)
- 1 no SI value
| Parameter | Value | Unit | Confidence | Source | Notes | Modelable |
|---|---|---|---|---|---|---|
| Current Density | 1.9 | A m⁻² | 90% | extracted | "A maximum power density (MPD) of 0.84 ± 0.05 W m−2 was obtained at a current den…" · T=30°C, pH(an)=7, substrate=sodium acetate | Modelable |
| Coulombic efficiency | 6.5 | % | 90% | extracted | "An apparent reduction of CE (from 83.9 ± 2.7% to 6.5 ± 2.2%) was observed with i…" · T=30°C, pH(an)=7, substrate=sodium acetate | Modelable |
| Voltage | 450 | mV | 90% | extracted | "the voltage was rapidly increased to 450.4 mV in the third cycle" · T=30°C, pH(an)=7, substrate=sodium acetate | Modelable |
| Corrected Coulombic Efficiency | 43.3 | % | 90% | extracted | "The CCE sharply decreased to 43.3 ± 5.0 % at the NO−3 -N concentration of 200 mg…" · T=30°C, pH(an)=7, substrate=sodium acetate | Excluded: not canonicalised (no canonical slug) |
| Power Density | 0.84 | W m⁻² | 90% | extracted | "A maximum power density (MPD) of 0.84 ± 0.05 W m−2 was obtained at a current den…" · T=30°C, pH(an)=7, substrate=sodium acetate | Modelable |
| Corrected Coulombic Efficiency | 92.4 | % | 90% | extracted | "the CCEs increased and then decreased, and a maximum value of 92.4 ± 3.0 % was o…" · T=30°C, pH(an)=7, substrate=sodium acetate | Excluded: not canonicalised (no canonical slug) |
| Nitrate Removal | 100 | % | 90% | extracted | "Additionally, almost all of NO−3 -N was removed by strain EB-1, indicating that …" · T=30°C, pH(an)=7, substrate=glucose | Modelable |
| Net COD/N Ratio | 3.23 | — | 90% | extracted | "For the denitrifying exoelectrogen EB-1, the net COD/N ratios for denitrificatio…" · T=30°C, pH(an)=7, substrate=sodium acetate | Excluded: not canonicalised (no canonical slug) |
| Net COD/N Ratio | 9.36 | — | 90% | extracted | "For the denitrifying exoelectrogen EB-1, the net COD/N ratios for denitrificatio…" · T=30°C, pH(an)=7, substrate=sodium acetate | Excluded: not canonicalised (no canonical slug) |
| Nitrate Removal | 82.8 | % | 90% | extracted | "Further, 82.8 ± 6.5 % NO−3 -N was removed within the first 6 h when 200 mg L−1 N…" · T=30°C, pH(an)=7, substrate=sodium acetate | Modelable |
| Nitrate Removal | 100 | % | 90% | extracted | "As shown in Figure 6B, almost all of nitrate was removed when the NO−3 -N concen…" · T=30°C, pH(an)=7, substrate=sodium acetate | Modelable |
| Net COD/N Ratio | 3.75 | — | 90% | extracted | "For the denitrifying exoelectrogen EB-1, the net COD/N ratios for denitrificatio…" · T=30°C, pH(an)=7, substrate=sodium acetate | Excluded: not canonicalised (no canonical slug) |
| Nitrate Removal×2 | 100 | % | 90% | extracted | "Additionally, almost all of NO−3 -N was removed by strain EB-1" · T=30°C, pH(an)=7, substrate=starch | Modelable |
| Net COD/N Ratio | 3.18 | — | 90% | extracted | "For the denitrifying exoelectrogen EB-1, the net COD/N ratios for denitrificatio…" · T=30°C, pH(an)=7, substrate=sodium acetate | Excluded: not canonicalised (no canonical slug) |
| Nitrate Removal | 0.66 | kg N m⁻³ d⁻¹ | 90% | extracted | "An average nitrate removal rate of 0.66 ± 0.01 kg N m−3 d−1 (27.7 ± 0.5 mg N L−1…" · T=30°C, pH(an)=7, substrate=sodium acetate | Excluded: no SI value |
Methodology
What was the system and how was it run
Methodology
Methodology
Two-chamber MFC with 15 mL anode and cathode separated by cation exchange membrane. Anode: carbon fiber felt (2 cm³); cathode: Pt-coated carbon cloth (7 cm²). Strain EB-1 isolated from enriched anodic biofilm via dilution plating and identified by 16S rDNA sequencing. Batch operation with 1 kΩ external resistance; voltage recorded every 5 min. Electrochemical analysis via polarization curves and cyclic voltammetry (CV) at 1 mV/s scan rate. Nitrogen species (NO₃⁻-N, NO₂⁻-N, NH₄⁺-N) quantified by UV spectrophotometry. Electron flux partitioned into anode respiration (from current), denitrification (from NO₃⁻-N loss), and other losses (biomass, overpotential).
System configuration
| Field | Value |
|---|---|
| reactor type | MFC |
| chamber config | 2-chamber |
Performance metrics
| Field | Value |
|---|---|
| citation count | 50 |
Operating conditions
4 runs extracted| Run | T°C | pHan | pHcat | Substrate | [S]mg/L | HRTh | Mode | R_extΩ | V_appV | Inoculum |
|---|---|---|---|---|---|---|---|---|---|---|
| v2-4c82d21436f581d9 | 30 | 7 | — | glucose | — | — | — | 1000 | — | — |
| v2-b05e904cce0c0f1a | 30 | 7 | — | sodium acetate | — | — | — | 1000 | — | — |
| v2-be15bbad0b0a63d4 | 30 | 7 | — | starch | — | — | — | 1000 | — | — |
| v2-e2b4a3872a3af6a8 | 30 | 7 | — | sucrose | — | — | — | 1000 | — | — |
Pipeline
Raw extractions, artifacts, quality signal
Extraction quality
honesty signalCalibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.
Parameter completeness
13%
Fraction of expected parameters extracted
Data completeness
30%
Overall extraction coverage across fields
AI confidence
78%
Model self-reported confidence
Mean parameter confidence
90%
Average confidence across PaperParameter rows surfaced above
review against source PDF before citing · scores 0–1
Chart explorer
Move the inputs this paper used and see how the predicted outcome shifts.
Explore model
The reactor in 3D, with flow you can switch on and off.
AI insights
Contradictions, gaps and opportunities found by comparing this paper with the corpus.
Compare similar papers
The nearest papers by system, materials and organisms, with their outcomes side by side.
Source PDF
The paper as published.
Representative model, generic MFC
Tap to interactRepresentative model, generic MFC
Representative MFC — matched on the paper’s system type only, not its reactor or geometry.
Keywords
- Microbial fuel cell
- Denitrifying bacteria
- Denitrification
- Nitrate
- Biofilm
- Wastewater
Cite
Xiaojun Jin, Fei Guo, Zhimei Liu et al. (2018). Enhancing the Electricity Generation and Nitrate Removal of Microbial Fuel Cells With a Novel Denitrifying Exoelectrogenic Strain EB-1. Frontiers in Microbiology. https://doi.org/10.3389/fmicb.2018.02633
- Journal
- Frontiers in Microbiology
Open in lab for full controls, parameter editing, and template overlays.
Open in lab