Paper · MDC
Accomplishing a N-E-W (nutrient-energy-water) synergy in a bioelectrochemical nitritation-anammox process
Summary
What the paper reports, in its own words.
Abstract
Abstract This study reports an investigation of the concept, application and performance of a novel bioelectrochemical nitritation-anammox microbial desalination cell (MDC) for resource-efficient wastewater treatment and desalination. Two configurations of anammox MDCs (anaerobic-anammox cathode MDC (AnA mox MDC) and nitration-anammox cathode MDC (NiA mox MDC)) were compared with an air cathode MDC (CMDC), operated in fed-batch mode. Results from this study showed that the maximum power density produced by NiA mox MDC (1,007 mW/m 3 ) was higher than that of AnA mox MDC (444 mW/m 3 ) and CMDC (952 mW/m 3 ). More than 92% of ammonium-nitrogen (NH 4 + -N) removal was achieved in NiA mox MDC, significantly higher than AnA mox MDC (84%) and CMDC (77%). The NiA mox MDC performed better than CMDC and AnA mox MDC in terms of power density, COD removal and salt removal in desalination chamber. In addition, cyclic voltammetry analysis of anammox cathode showed a redox peak centered at −140 mV Vs Ag/AgCl confirming the catalytic activity of anammox bacteria towards the electron transfer process. Further, net energy balance of the NiA mox MDC was the highest (NiA mox MDC-0.022 kWh/m 3 >CMDC-0.019 kWh/m 3 >AnA mox MDC-0.021 kWh/m 3 ) among the three configurations. This study demonstrated, for the first time, a N-E-W synergy for resource-efficient wastewater treatment using nitritation-anammox process.
AI summary
82% confidenceThis study demonstrates a bioelectrochemical nitritation-anammox microbial desalination cell (NiAmoxMDC) that couples partial nitrification, anammox, and desalination in a single system. The NiAmoxMDC achieved 92% NH₄⁺-N removal and 1,007 mW/m³ power density, outperforming an anaerobic anammox MDC (444 mW/m³, 84% removal) and air cathode control (952 mW/m³, 77% removal). However, aeration at 10 ml/min caused NO₂⁻-N accumulation (6.3–10.3 mg/L) and anammox inhibition by cycles 3–4, which was partially reversed by reducing aeration to 3 ml/min. The system achieved near energy-neutral operation (−0.022 kWh/m³) with 54% salt removal.
Key insights
Threshold Aeration at 10 ml/min caused NO₂⁻-N accumulation from 0 to 10.3 mg/L over 4 cycles and reduced NH₄⁺-N removal from 98.3% to 78.6%, indicating anammox inhibition under aerobic stress.
So what. Operators must reduce aeration to 3 ml/min (DO ~1.6 mg/L) to maintain anammox activity and prevent nitrite accumulation, even though this reduces power density.
Trade-off Reducing aeration from 10 to 3 ml/min increased total nitrogen removal by 66.6% (from ~25% to 75%) in NiAmoxMDC, demonstrating a critical operating window for nitritation-anammox balance.
So what. Design cathode aeration control to maintain low DO (1.6 mg/L) rather than maximizing oxygen transfer; this is the key trade-off between power and nitrogen removal.
Mechanism NiAmoxMDC generated 1,007 mW/m³ with two terminal electron acceptors (O₂ reduction + anammox NO₂⁻ reduction), compared to 444 mW/m³ for anaerobic anammox alone, a 2.3× improvement.
So what. Aerated biocathodes with anammox can generate higher power than anaerobic anammox alone, but only if aeration is controlled to prevent anammox inhibition.
Mechanism Ohmic resistance in anaerobic AnAmoxMDC was 97.3 Ω versus 50.1 Ω in aerated NiAmoxMDC, a 1.94× difference attributed to biofouling of ion exchange membranes under anaerobic conditions.
So what. Maintain cathode aeration not only for nitritation but also to reduce membrane biofouling and ohmic losses; this improves both nitrogen removal and electrical performance.
Performance Coulombic efficiency remained low (17–26%) despite high COD removal (62–72%), because glucose is fermentable and supports competing non-electrochemical pathways (fermentation, methanogenesis).
So what. For future work, test with less fermentable substrates (e.g., acetate) to improve CE and validate whether the power and nitrogen removal gains hold under higher CE conditions.
Contradictions2
Tensions the paper itself points to. Each side quotes the passage it comes from.
Within the paper Aeration improves power and reduces ohmic resistance, but inhibits anammox and causes nitrite accumulation.
One sideNiAmoxMDC at 10 ml/min aeration: 1,007 mW/m³ power, 50.1 Ω ohmic resistance, 92% NH₄⁺-N removal in cycles 1–2
“The maximum power density produced by NiAmoxMDC (1,007 mW/m³) was higher than that of AnAmoxMDC (444 mW/m³)”
Other sideSame system cycles 3–4: NO₂⁻-N accumulation to 10.3 mg/L, NH₄⁺-N removal drops to 78.6%, anammox inhibited
“accumulation of NO₂⁻-N and decrease in the removal rates of NH₄⁺-N in third and fourth cycles confirmed the inhibition effect on the anammox process due to continued exposure of anammox bacteria to aerobic condition”
Authors’ reading. Authors attribute this to oxygen toxicity to anammox bacteria over time; the solution is to reduce aeration to 3 ml/min, which restores 75% TN removal but likely reduces power. This is a fundamental trade-off, not a true contradiction, but the paper does not quantify power at 3 ml/min aeration.
Within the paper Coulombic efficiency is low despite high COD removal, suggesting most organic matter is not converted to electricity.
One sideCOD removal 72.1% in NiAmoxMDC
“COD removal efficiency was significantly higher in NiAmoxMDC (ANOVA, p < 0.0001)”
Other sideCoulombic efficiency only 25.6% in NiAmoxMDC
“the CE of NiAmoxMDC was only 25 ± 6.4%, indicating that a substantial portion of COD utilization was not associated with electron release”
Authors’ reading. Authors explain this is due to glucose fermentation and methanogenesis competing with electrochemical oxidation. This is expected for glucose but limits the energy-positive claim; the paper does not test non-fermentable substrates.
Opportunity areas6
Specific gaps in this paper, with an experiment that would close each.
High Aeration rate and dissolved oxygen setpoint were not systematically varied; only two points tested (10 ml/min and 3 ml/min). Optimal DO window for balancing nitritation, anammox activity, and power generation is unknown.
Paper shows 10 ml/min causes anammox inhibition by cycle 3–4 (NO₂⁻-N rises to 10.3 mg/L), but 3 ml/min restores 75% TN removal. No intermediate points (5, 7 ml/min) or DO targets (0.5, 1.0, 2.0 mg/L) tested. Power density at 3 ml/min not reported.
Try. Vary aeration rate (2–10 ml/min) or set DO setpoint (0.5–3.0 mg/L) in fed-batch cycles; measure power density, NH₄⁺-N removal, NO₂⁻-N accumulation, and anammox activity (e.g., N₂ production rate) at each point.
High Substrate choice (glucose) is highly fermentable and suppresses coulombic efficiency to 25.6%. No comparison with acetate or other less fermentable substrates.
Text states: 'glucose was used as an organic substrate...fermentable substrate, which implies its possible consumption by diverse competing metabolisms such as fermentation and methanogens that do not contribute towards columbic efficiency.' Supplementary Table S3 compares to other nitritation-anammox systems but not to MES systems using acetate.
Try. Run parallel NiAmoxMDC fed-batch cycles with acetate (10–20 mM) at same aeration (3 ml/min); measure power density, CE, COD removal, and nitrogen removal to determine if substrate choice is the limiting factor.
Medium Hydraulic retention time (HRT) and batch cycle duration not specified; fed-batch mode means HRT varies. No kinetic data on nitritation or anammox rates.
Paper states 'operated in fed-batch mode' but does not report cycle duration, volume exchanged per cycle, or HRT. Supplementary Table S2 shows removal rates per cycle but not per hour. Nitritation-anammox kinetics (e.g., specific nitritation rate, anammox rate) not measured.
Try. Report cycle duration and HRT; measure time-course of NH₄⁺-N, NO₂⁻-N, NO₃⁻-N, and N₂ production within a single cycle to quantify nitritation and anammox kinetics at 3 ml/min aeration.
Medium N₂ production (the desired end product of anammox) was not directly measured. Nitrogen balance relies on mass balance (input NH₄⁺ + NO₂⁻ minus output NH₄⁺ + NO₂⁻ + NO₃⁻).
Text states anammox oxidizes ammonium to nitrogen gas, but no N₂ measurement (e.g., gas chromatography, ¹⁵N tracing) provided. Nitrogen recovery is inferred from disappearance of NH₄⁺ and NO₂⁻, but some may be assimilated into biomass or lost as N₂O.
Try. Measure N₂ production by headspace gas chromatography or ¹⁵N-labeled batch experiments; quantify N₂O production to confirm anammox selectivity and rule out competing denitrification pathways.
Medium Cathode potential (vs. SHE or Ag/AgCl) during operation not reported; only redox peak from cyclic voltammetry (−140 mV vs Ag/AgCl) provided. Operating cathode potential window unknown.
CV shows redox peak but not the steady-state cathode potential during fed-batch operation. Polarization curves (Fig. 2B) show voltage but not electrode potentials. No data on how cathode potential affects nitritation vs. anammox selectivity.
Try. Measure cathode potential (vs. Ag/AgCl reference) during fed-batch cycles at 3 ml/min aeration; correlate with NH₄⁺-N removal, NO₂⁻-N accumulation, and power output to define optimal operating window.
Low Desalination performance limited by low ion exchange membrane (IEM) surface area ratio (0.8:1 cm²/cm³) and volumetric ratio (1.5 v/v). Scaling factors for salt removal not explored.
Text states: 'At a higher volumetric ratio of 100 (v/v)...93% salt removal was reported' vs. 53.9% in this study at 1.5 v/v. Authors acknowledge this but do not test higher ratios or larger IEM areas.
Try. Increase volumetric ratio to 5–10 (v/v) and IEM surface area ratio to ≥2 (cm²/cm³); measure salt removal and power density to determine if desalination can be improved without sacrificing nitrogen removal.
Generated by MESSAI extraction pipeline · review against source PDF
Extracted values
Every value pulled from the paper, with its source, so each number can be checked against the text.
n = 142 extracted values
Select a citation to see the quote, page and confidence behind a value.
78 of 141 extracted rows modelable
- 30 not canonicalised (no canonical slug)
- 21 no SI value
- 6 outside physical bounds
- 4 not marked applicable to modeling
- 2 verifier rejected the value
| Parameter | Value | Unit | Confidence | Source | Notes | Modelable |
|---|---|---|---|---|---|---|
| Substrate | wastewater | — | 80% | llm | ||
| Standard Potential×2 | -140 | mV Vs Ag/AgCl | 95% | cyclic voltammetry | "cyclic voltammetry analysis of anammox cathode showed a redox peak centered at −…" · T=22°C, steady_state | Excluded: not marked applicable to modeling |
| Chemical Oxygen Demand (COD) Removal×2 | 72.1 | % | 95% | cod assay (closed-reflux) | "and NiAmoxMDC over the fed-batch cycles were 65.8 ± 1.56% (n = 8; SD = 1.56), 62…" · T=22°C, substrate=glucose, steady_state | Modelable |
| Salt Removal×2 | 43 | % | 95% | conductivity measurement | "The average salinity removal rates (TDS removal) in CMDC, AnAmoxMDC and NiAmoxMD…" · T=22°C, substrate=glucose, steady_state | Modelable |
| Ohmic Resistance×2 | 50.1 | Ω | 95% | electrochemical impedance spectroscopy | "EIS measurements indicated that the ohmic resistance of AnAmoxMDC was 97.3 Ω, wh…" · T=22°C, substrate=glucose, steady_state | Modelable |
| Salt Removal×2 | 54.4 | % | 95% | conductivity measurement | "The average salinity removal rates (TDS removal) in CMDC, AnAmoxMDC and NiAmoxMD…" · T=22°C, substrate=glucose, steady_state | Modelable |
| Substrate Concentration×2 | 6.3 | mg/L | 95% | colorimetric analysis | "The accumulated NO2−-N concentration at the end of the third and fourth cycles w…" · T=22°C, substrate=glucose, degradation | Modelable |
| Ammonium-N Removed×2 | 84.8 | % | 95% | colorimetric analysis | "at the end of the third and fourth cycles, accumulation of nitrite was observed …" · T=22°C, substrate=glucose, degradation | Modelable |
| Anode Oxidation Current×2 | 706 | µA | 95% | cyclic voltammetry | "The results showed that NiAmoxMDC produced higher oxidation current of 706 µA co…" · T=22°C, substrate=glucose, steady_state | Excluded: not canonicalised (no canonical slug) |
| Anode Oxidation Current×2 | 254 | µA | 95% | cyclic voltammetry | "The results showed that NiAmoxMDC produced higher oxidation current of 706 µA co…" · T=22°C, substrate=glucose, steady_state | Excluded: not canonicalised (no canonical slug) |
| Anode Oxidation Current×2 | 77.7 | µA | 95% | cyclic voltammetry | "The results showed that NiAmoxMDC produced higher oxidation current of 706 µA co…" · T=22°C, substrate=glucose, steady_state | Excluded: not canonicalised (no canonical slug) |
| Salt Removal×2 | 53.9 | % | 95% | conductivity measurement | "The average salinity removal rates (TDS removal) in CMDC, AnAmoxMDC and NiAmoxMD…" · T=22°C, substrate=glucose, steady_state | Modelable |
| Ammonium-N Removed×2 | 98.3 | % | 95% | colorimetric analysis | "The results showed that in NiAmoxMDC, nitrite was not detected and NH4+-N remova…" · T=22°C, substrate=glucose, steady_state | Modelable |
| Substrate Concentration×2 | 10.3 | mg/L | 95% | colorimetric analysis | "The accumulated NO2−-N concentration at the end of the third and fourth cycles w…" · T=22°C, substrate=glucose, degradation | Modelable |
| Power Density Volumetric×2 | 1,010 | mW/m³ | 95% | polarization curve | "the maximum power density produced by NiAmoxMDC (1,007 mW/m3) was higher than th…" · T=22°C, substrate=glucose, steady_state | Excluded: verifier rejected the value |
| Ohmic Resistance×2 | 97.3 | Ω | 95% | electrochemical impedance spectroscopy | "EIS measurements indicated that the ohmic resistance of AnAmoxMDC was 97.3 Ω, wh…" · T=22°C, substrate=glucose, steady_state | Modelable |
| Ammonium-N Removed×2 | 85.6 | % | 95% | colorimetric analysis | "ammonium-nitrogen removal for the first, second, third, and fourth batch cycles …" · T=22°C, substrate=glucose, steady_state | Modelable |
| Ammonium-N Removed×2 | 97.8 | % | 95% | colorimetric analysis | "NH4+-N removal was 98.3% and 97.8% (Supplementary Table S2) at the end of first …" · T=22°C, substrate=glucose, steady_state | Modelable |
| Chemical Oxygen Demand (COD) Removal×2 | 62.1 | % | 95% | cod assay (closed-reflux) | "COD removal rates in the anode chambers of CMDC, AnAmoxMDC, and NiAmoxMDC over t…" · T=22°C, substrate=glucose, steady_state | Modelable |
| Ammonium-N Removed×2 | 81.6 | % | 95% | colorimetric analysis | "ammonium-nitrogen removal for the first, second, third, and fourth batch cycles …" · T=22°C, substrate=glucose, steady_state | Modelable |
| Electrical Conductivity×2 | 17.9 | mS/cm | 95% | conductivity measurement | "The electrical conductivity of 10 g/L of NaCl at 25 °C was 17.92 mS/Cm" · T=25°C | Modelable |
| Ammonium-N Removed×2 | 79.5 | % | 95% | colorimetric analysis | "ammonium-nitrogen removal for the first, second, third, and fourth batch cycles …" · T=22°C, substrate=glucose, startup | Modelable |
| Power Density Volumetric×2 | 444 | mW/m³ | 95% | polarization curve | "the maximum power density produced by NiAmoxMDC (1,007 mW/m3) was higher than th…" · T=22°C, substrate=glucose, steady_state | Modelable |
| Power Density Volumetric×2 | 952 | mW/m³ | 95% | polarization curve | "the maximum power density produced by NiAmoxMDC (1,007 mW/m3) was higher than th…" · T=22°C, substrate=glucose, steady_state | Modelable |
| Ammonium-N Removed×2 | 78.6 | % | 95% | colorimetric analysis | "the removal rate of NH4+-N was decreased to 84.8% and 78.6%" · T=22°C, substrate=glucose, degradation | Modelable |
Methodology
What was the system and how was it run
Methodology
Methodology
Three MDC configurations (NiAmoxMDC with aerated nitritation-anammox biocathode, AnAmoxMDC with anaerobic anammox biocathode, and CMDC with abiotic air cathode) were operated in fed-batch mode for >1,100 hours with identical reactor sizes. Cathode chambers were fed 70 mg/L NH₄⁺-N (and 70 mg/L NO₂⁻-N for AnAmoxMDC) at two aeration rates (10 ml/min initially, then 3 ml/min). Anode chambers received glucose substrate. Nitrogen species (NH₄⁺-N, NO₂⁻-N, NO₃⁻-N) were measured by ion chromatography at the end of each cycle. Power density, current density, and polarization curves were recorded. Electrochemical characterization included cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Desalination performance was assessed by total dissolved solids (TDS) removal in the middle chamber.
System configuration
| Field | Value |
|---|---|
| reactor type | MDC |
| chamber config | 3-chamber |
Electrode specifications
| Field | Value |
|---|---|
| cathode material | air cathode |
Performance metrics
| Field | Value |
|---|---|
| citation count | 25 |
Operational parameters
| Field | Value |
|---|---|
| substrate | ["wastewater"] |
Operating conditions
6 runs extracted| Run | T°C | pHan | pHcat | Substrate | [S]mg/L | HRTh | Mode | R_extΩ | V_appV | Inoculum |
|---|---|---|---|---|---|---|---|---|---|---|
| v2-23890a68cfbc0479 | 22 | — | — | glucose | 468.7 | — | steady_state | 1000 | — | — |
| v2-327e11be5622afa1 | 22 | — | — | — | — | — | steady_state | — | — | — |
| v2-58a2540478c500d8 | 25 | — | — | — | — | — | — | — | — | — |
| v2-760fcc0cb350b21c | 25 | — | — | — | 468.7 | — | — | — | — | — |
| v2-e214e7fa679d1a98 | 22 | — | — | glucose | 468.7 | — | degradation | 1000 | — | — |
| v2-e608a9509276d46a | 22 | — | — | glucose | 468.7 | — | startup | 1000 | — | — |
Microbial kinetics
2 constants| Organism | Substrate | Parameter | Value | Unit | Conf. |
|---|---|---|---|---|---|
| anammox bacteria | (unspecified) | doubling_time | 11 | days | 100% |
| anammox bacteria | (unspecified) | doubling_time | 11 | days | 100% |
Pipeline
Raw extractions, artifacts, quality signal
Extraction quality
honesty signalCalibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.
Parameter completeness
50%
Fraction of expected parameters extracted
Data completeness
60%
Overall extraction coverage across fields
AI confidence
82%
Model self-reported confidence
Mean parameter confidence
78%
Average confidence across PaperParameter rows surfaced above
review against source PDF before citing · scores 0–1
Chart explorer
Move the inputs this paper used and see how the predicted outcome shifts.
Explore model
The reactor in 3D, with flow you can switch on and off.
AI insights
Contradictions, gaps and opportunities found by comparing this paper with the corpus.
Compare similar papers
The nearest papers by system, materials and organisms, with their outcomes side by side.
Source PDF
The paper as published.
Representative model, generic microbial desalination cell
Tap to interactRepresentative model, generic microbial desalination cell
Representative microbial desalination cell — matched on the paper’s system type only, not its reactor or geometry.
Keywords
- Anammox
- MOX fuel
- Wastewater
- Sewage treatment
- Desalination
- Nuclear chemistry
Cite
Umesh Ghimire, Veera Gnaneswar Gude (2019). Accomplishing a N-E-W (nutrient-energy-water) synergy in a bioelectrochemical nitritation-anammox process. Scientific Reports. https://doi.org/10.1038/s41598-019-45620-2
- Journal
- Scientific Reports
Open in lab for full controls, parameter editing, and template overlays.
Open in lab