Research

Paper · MFC

Enhanced low C/N nitrogen removal in an innovative microbial fuel cell (MFC) with electroconductivity aerated membrane (EAM) as biocathode

01

Summary

What the paper reports, in its own words.

3D Interactive ModelAI Enhanced· 78%

AI summary

78% confidence

This study couples an electroconductivity aerated membrane (EAM) biocathode with a microbial fuel cell (MFC) anode to achieve simultaneous nitrification–denitrification (SND) at low C/N ratio (2.89 g COD g⁻¹ NH₄⁺-N). Operating at 5 Ω external resistance and 0.2–0.5 mg L⁻¹ dissolved oxygen, the system achieved 80.81% total nitrogen removal (0.128 kg TN m⁻³ d⁻¹), 94.73% COD removal, and 4.20 W m⁻³ power density. Electrochemical denitrification improved TN removal by 19.80% versus open circuit, with cathode coulombic efficiency reaching 42.84% for NO₃⁻-N reduction. The controlled aeration in the EAM prevented oxygen diffusion to the anode, enabling higher anode coulombic efficiency (40.67%) than prior MFC–MBR systems.

Key insights

  • Trade-off Decreasing external resistance from 100 Ω to 5 Ω increased current density from 0.36 to 4.10 A m⁻² and improved TN removal efficiency from ~60% to 80.81%, demonstrating that higher electron flux drives electrochemical denitrification.

    So what. Operators should minimize external resistance to maximize current density when the goal is nitrogen removal; however, this trades off against power density, which peaked at 10 Ω (4.20 W m⁻³).

  • Threshold Nitrite accumulated from barely detectable to 2.32 mg L⁻¹ as external resistance decreased and current increased, indicating incomplete reduction of NO₃⁻ to N₂ under high electron flux.

    So what. Operators must monitor and control cathode potential or current density to avoid NO₂⁻ accumulation; intermediate products suggest incomplete denitrification kinetics or electron acceptor competition.

  • Mechanism Maintaining cathode dissolved oxygen at 0.2–0.5 mg L⁻¹ prevented oxygen diffusion to the anode, achieving anode coulombic efficiency of 40.67% at 5 Ω, substantially higher than prior MFC–MBR systems (1.5–21%).

    So what. Use membrane aeration with tight DO control (0.2–0.5 mg L⁻¹) to prevent oxygen crossover; this design choice is critical for maintaining anode efficiency in coupled MFC–MABR systems.

  • Performance The system achieved COD/N ratio of 2.89 g COD g⁻¹ NH₄⁺-N, lower than traditional MABR (5 g COD g⁻¹ NH₄⁺-N) and comparable to advanced sequencing batch reactors (2–3 g COD g⁻¹ TN), despite only 19.80% improvement from electrochemical denitrification versus open circuit.

    So what. This system is suitable for low-C/N wastewaters; however, the modest 19.80% improvement suggests that bioelectrochemical denitrification alone cannot fully compensate for carbon limitation—hybrid approaches or external electron donors may be needed.

  • Mechanism Cathode potential remained at maximum 0.18 V vs SHE, well below the standard potentials for O₂ (0.805 V), NO₃⁻ (0.433 V), and NO₂⁻ (0.350 V) reduction, indicating large overpotential losses and energy inefficiency at the cathode.

    So what. Cathode overpotential is a major loss mechanism; improving cathode kinetics (biofilm composition, electrode material, or mediators) should be prioritized to increase power output and denitrification rate.

Opportunity areas6

Specific gaps in this paper, with an experiment that would close each.

  • High No systematic study of cathode potential vs current density relationship; cathode potential remained at 0.18 V vs SHE across all loads, suggesting it may be limited by biofilm kinetics or mass transfer rather than electrochemistry.

    Authors note 'large energy loss occurred at the cathode' and attribute it to overpotential, intermediate products (NO₂, N₂O), and microbial maintenance, but do not vary cathode potential independently or measure N₂O.

    Try. Potentiostatic control of cathode at 0.0, −0.1, −0.2, −0.3 V vs SHE; measure NO₂⁻ and N₂O accumulation; quantify electron recovery to N₂ vs N₂O.

  • High No measurement of N₂O production or quantification of N₂ as final product; nitrogen balance incomplete.

    Authors assume N₂ is the final product in coulombic efficiency calculation (Eq. 4, n=5 for NO₃⁻) but provide no gas chromatography or isotope data. Nitrite accumulation (2.32 mg L⁻¹) suggests incomplete reduction; N₂O may be produced.

    Try. Gas-phase sampling (GC-ECD or IRMS) for N₂O and N₂; nitrogen balance closure; test at different cathode potentials and DO levels.

  • Medium Aeration intensity tested at only two levels (30 kPa, 20 kPa); no systematic optimization of DO setpoint for SND vs power generation trade-off.

    Authors state 'The dissolved oxygen of the cathode liquor was controlled at 0.2-0.5 mg L⁻¹ throughout the study' but Table 1 shows only two aeration pressures tested, with minimal difference in anode CE (0.34% decrease). Optimal DO window for SND is known to be 0.3–0.8 mg L⁻¹ from prior work (Munch, Pochana–Keller cited).

    Try. Vary DO setpoint from 0.1 to 1.0 mg L⁻¹ in 0.1 mg L⁻¹ increments; measure TN removal, power density, NO₂⁻ and N₂O accumulation at each level.

  • Medium No investigation of HRT effect on nitrogen removal and electrochemical denitrification; only one HRT (12 h) tested.

    HRT is a critical operating parameter for SND and biofilm kinetics. Authors operated at fixed 12 h HRT; no data on shorter (6–8 h) or longer (18–24 h) retention times.

    Try. Test HRT 6, 9, 12, 15, 18 h at constant current density (e.g., 4 A m⁻²); measure TN removal rate, NO₂⁻ accumulation, and biofilm thickness.

  • Medium No characterization of biofilm composition or microbial community; mechanisms of SND inferred but not verified.

    Authors propose layered biofilm with nitrifiers in inner aerobic zone and denitrifiers in outer anaerobic zone (Fig. 6), but provide no microscopy, 16S rRNA, or functional gene data.

    Try. FISH or 16S rRNA sequencing of cathode biofilm at different depths; quantify nitrifier and denitrifier abundance; correlate with NO₂⁻ accumulation and current density.

  • Low C/N ratio in influent is fixed at 2.8 g COD g⁻¹ N; no variation to test the claimed 'low C/N' capability or identify the minimum C/N at which the system fails.

    Authors claim advantage at 'low COD/N ratio of 2.8' but do not test lower ratios (e.g., 1.5, 1.0) or higher ratios (e.g., 4, 5) to establish operating window.

    Try. Vary influent C/N from 1.0 to 5.0 g COD g⁻¹ N; measure TN removal efficiency, NO₂⁻ accumulation, and power density; identify threshold below which performance degrades.

Generated by MESSAI extraction pipeline · review against source PDF

02

Extracted values

Every value pulled from the paper, with its source, so each number can be checked against the text.

n = 57 extracted values

Select a citation to see the quote, page and confidence behind a value.

27 of 57 extracted rows modelable

  • 26 not canonicalised (no canonical slug)
  • 4 no SI value
ParameterValueUnitConfidenceSourceNotesModelable
Coulombic Efficiency of cathode42.5%90%
extracted
"CE of cathode (%): 42.48 ± 0.89 at Resistance 5 ȍ" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateExcluded: not canonicalised (no canonical slug)
Current Density4.1A m⁻²90%
extracted
"Current density (A m-2): 4.10 ± 0.01 at Resistance 10 ȍ and Aeration Intensity 2…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Current Density1.2A m⁻²90%
extracted
"Current density (A m-2): 1.20 ± 0.02 at Resistance 50 ȍ and Aeration Intensity 2…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Coulombic Efficiency of anode14.4%90%
extracted
"CE of anode (%): 14.42 ± 0.27 at Resistance 50 ȍ" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateExcluded: not canonicalised (no canonical slug)
Coulombic Efficiency of cathode41.5%90%
extracted
"CE of cathode (%): 41.45 ± 0.93 at Resistance 10 ȍ" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateExcluded: not canonicalised (no canonical slug)
Coulombic Efficiency of anode38.9%90%
extracted
"CE of anode (%): 38.90 ± 0.49 at Resistance 10 ȍ" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateExcluded: not canonicalised (no canonical slug)
Coulombic Efficiency of anode40.7%90%
extracted
"CE of anode (%): 40.67 ± 1.25 at Resistance 5 ȍ" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateExcluded: not canonicalised (no canonical slug)
Coulombic Efficiency of cathode13%90%
extracted
"CE of cathode (%): 12.96 ± 0.44 at Resistance 50 ȍ" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateExcluded: not canonicalised (no canonical slug)
Coulombic Efficiency of anode9.61%90%
extracted
"CE of anode (%): 9.61 ± 0.38 at Resistance 100 ȍ and Aeration Intensity 20 kPa" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateExcluded: not canonicalised (no canonical slug)
Coulombic Efficiency of cathode8.11%90%
extracted
"CE of cathode (%): 8.11 ± 0.26 at Resistance 100 ȍ" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateExcluded: not canonicalised (no canonical slug)
Coulombic Efficiency of anode9.27%90%
extracted
"CE of anode (%): 9.27 ± 0.33 at Resistance 100 ȍ" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateExcluded: not canonicalised (no canonical slug)
Power Density Volumetric4.2W m⁻³90%
extracted
"The best performance of power density (4.20 ± 0.12 W m-3 obtained at a current d…" · T=28°C, substrate=sodium acetate, HRT=12hModelable
Current22mA90%
extracted
"Current (mA): 22.00 ± 0.03 at Resistance 5 ȍ and Aeration Intensity 20 ± 0.76 kP…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Voltage110mV90%
extracted
"Voltage (mV): 110 ± 3.29 at Resistance 5 ȍ and Aeration Intensity 20 ± 0.76 kPa" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Power Density Volumetric2.42W m⁻³90%
extracted
"Power density (W m-3): 2.42 ± 0.03 at Resistance 5 ȍ and Aeration Intensity 20 ±…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Current20.5mA90%
extracted
"Current (mA): 20.50 ± 0.07 at Resistance 10 ȍ and Aeration Intensity 20 ± 0.76 k…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Voltage205mV90%
extracted
"Voltage (mV): 205 ± 7.11 at Resistance 10 ȍ and Aeration Intensity 20 ± 0.76 kPa" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Current Density4.4A m⁻²90%
extracted
"Current density (A m-2): 4.40 ± 0.01 at Resistance 5 ȍ and Aeration Intensity 20…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Voltage469mV90%
extracted
"The maximum voltage output reached 469 mV (1000 ȍ) after a 15-day start-up perio…" · T=28°C, substrate=sodium acetateModelable
Current6mA90%
extracted
"Current (mA): 6.00 ± 0.11 at Resistance 50 ȍ and Aeration Intensity 20 ± 0.76 kP…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Power Density Volumetric1.8W m⁻³90%
extracted
"Power density (W m-3): 1.80 ± 0.11 at Resistance 50 ȍ and Aeration Intensity 20 …" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Voltage300mV90%
extracted
"Voltage (mV): 300 ± 10.93 at Resistance 50 ȍ and Aeration Intensity 20 ± 0.76 kP…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Voltage360mV90%
extracted
"Voltage (mV): 360 ± 12.57 at Resistance 100 ȍ and Aeration Intensity 20 ± 0.76 k…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Voltage387mV90%
extracted
"Voltage (mV): 387 ± 15.29 at Resistance 100 ȍ and Aeration Intensity 30 ± 1.14 k…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Current3.6mA90%
extracted
"Current (mA): 3.60 ± 0.13 at Resistance 100 ȍ and Aeration Intensity 20 ± 0.76 k…" · T=28°C, substrate=sodium acetate, HRT=12h, steady_stateModelable
Showing 25 of 57

Methodology

What was the system and how was it run

Methodology

Methodology

The system consists of a two-chamber MFC with a carbon felt anode and an electroconductivity aerated membrane (EAM) biocathode operating as a membrane-aerated biofilm reactor (MABR). Synthetic wastewater (0.38 g NaAc L⁻¹, 0.3 g NH₄Cl L⁻¹) is fed to the cathode at 1.39 mL min⁻¹ (HRT 12 h) in continuous mode; the anode is operated intermittently. Cathode dissolved oxygen is maintained at 0.2–0.5 mg L⁻¹ via airflow control. External resistance is varied from 1000 Ω (open circuit) to 0 Ω (short circuit); voltage, current, and electrode potentials (vs Ag/AgCl) are recorded continuously. Influent and effluent samples are analyzed daily for COD, NH₄⁺-N, NO₃⁻-N, NO₂⁻-N, and pH using standard colorimetric methods. Coulombic efficiency is calculated from integrated current and COD removal (anode) or nitrogen species reduction (cathode).

System configuration

FieldValue
reactor typeMFC
chamber config2-chamber

Operating conditions

10 runs extracted
RunT°CpHanpHcatSubstrate[S]mg/LHRThModeR_extΩV_appVInoculum
v2-1d0ecc5f4142682f28——sodium acetate—12————
v2-203ed09b6038f89e28——sodium acetate—12—10——
v2-3ee1a0dca5612dc428——sodium acetate—12steady_state10——
v2-45861e65fedefe3328——sodium acetate—12steady_state50——
v2-48be8f3e80c5d08528——sodium acetate—12steady_state100——
v2-7ba0488eef7a1f4b28——sodium acetate—12steady_state5——
v2-89c5b229355618f828——sodium acetate—12steady_state———
v2-9f8b8b115d463e4d28——sodium acetate—12—5——
v2-a30c9d61233f029528——sodium acetate———1000——
v2-a942381a50ff30b428——sodium acetate——steady_state1000——

Pipeline

Raw extractions, artifacts, quality signal

Extraction quality

honesty signal

Calibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.

AI confidence

78%

Model self-reported confidence

Mean parameter confidence

90%

Average confidence across PaperParameter rows surfaced above

review against source PDF before citing · scores 0–1

03

Chart explorer

Move the inputs this paper used and see how the predicted outcome shifts.

04

Explore model

The reactor in 3D, with flow you can switch on and off.

05

AI insights

Contradictions, gaps and opportunities found by comparing this paper with the corpus.

06

Compare similar papers

The nearest papers by system, materials and organisms, with their outcomes side by side.

07

Source PDF

The paper as published.

loading 3D model…

Representative model, generic MFC

Representative MFC — matched on the paper’s system type only, not its reactor or geometry.

MFC
System
4.40amperes per square metre
Best result · Current density
best of 5
57
Extracted values
2016
Year

Keywords

  • Microbial fuel cell
  • Anode
  • Aeration
  • Cathode
  • Wastewater
  • Chemical oxygen demand

Cite

Yun Wu, Qing Yang, Qingnan Zeng et al. (2016). Enhanced low C/N nitrogen removal in an innovative microbial fuel cell (MFC) with electroconductivity aerated membrane (EAM) as biocathode. Chemical Engineering Journal. https://doi.org/10.1016/j.cej.2016.11.141

Open in lab for full controls, parameter editing, and template overlays.

Open in lab