Research

Paper · MFC

Identification of Electrode Respiring, Hydrocarbonoclastic Bacterial Strain Stenotrophomonas maltophilia MK2 Highlights the Untapped Potential for Environmental Bioremediation

01

Summary

What the paper reports, in its own words.

3D Interactive ModelAI Enhanced· 72%Substrate ·pure compound

Abstract

Electrode respiring bacteria (ERB) possess a great potential for many biotechnological applications such as microbial electrochemical remediation systems (MERS) because of their exoelectrogenic capabilities to degrade xenobiotic pollutants. Very few ERB have been isolated from MERS, those exhibited a bioremediation potential toward organic contaminants. Here we report once such bacterial strain, Stenotrophomonas maltophilia MK2, a facultative anaerobic bacterium isolated from a hydrocarbon fed MERS, showed a potent hydrocarbonoclastic behavior under aerobic and anaerobic environments. Distinct properties of the strain MK2 were anaerobic fermentation of the amino acids, electrode respiration, anaerobic nitrate reduction and the ability to metabolize n-alkane components (C8–C36) of petroleum hydrocarbons (PH) including the biomarkers, pristine and phytane. The characteristic of diazoic dye decolorization was used as a criterion for pre-screening the possible electrochemically active microbial candidates. Bioelectricity generation with concomitant dye decolorization in MERS showed that the strain is electrochemically active. In acetate fed microbial fuel cells (MFCs), maximum current density of 273 ± 8 mA/m² (1000 Ω) was produced (power density 113 ± 7 mW/m²) by strain MK2 with a coulombic efficiency of 34.8%. Further, the presence of possible alkane hydroxylase genes (alkB and rubA) in the strain MK2 indicated that the genes involved in hydrocarbon degradation are of diverse origin. Such observations demonstrated the potential of facultative hydrocarbon degradation in contaminated environments. Identification of such a novel petrochemical hydrocarbon degrading ERB is likely to offer a new route to the sustainable bioremedial process of source zone contamination with simultaneous energy generation through MERS.

AI summary

72% confidence

This paper isolates and characterizes Stenotrophomonas maltophilia MK2, a facultative anaerobic bacterium capable of electrode respiration and hydrocarbon degradation. In acetate-fed MFCs, the strain generated 273 mA/m² current density and 34.8% coulombic efficiency. The strain degraded diesel-range organics (DRO, 8000 mg/L) completely under both aerobic (>90% in 100 h) and anaerobic nitrate-reducing conditions (100% by day 10). Genomic analysis revealed alkB and rubA genes encoding alkane hydroxylase. However, the paper focuses on hydrocarbon remediation potential rather than nitrogen cycling, providing limited insight into denitrification kinetics, N2O formation, or operating windows for nitrogen species management.

Key insights

  • Threshold Anaerobic DRO degradation (8000 mg/L) required 10 days to reach 100% removal with nitrate as electron acceptor, versus >90% in 100 hours aerobically, a ~2.4-fold slowdown.

    So what. If designing a bioelectrochemical remediation system for anaerobic hydrocarbon plumes, expect significantly longer residence times or higher current density to accelerate nitrate-dependent degradation.

  • Mechanism RB5 azo dye decolorization was faster anaerobically (96.23% in 48 h) than aerobically (97.99% in 72 h), suggesting anaerobic reduction pathways are kinetically favored for this strain.

    So what. Anaerobic operation may be preferable for azo dye remediation in MES, but this advantage does not extend to hydrocarbon degradation, indicating substrate-dependent metabolic switching.

  • Performance Coulombic efficiency plateaued at 34.8% in acetate-fed MFCs, indicating substantial substrate loss to non-electrochemical pathways (fermentation, biosynthesis).

    So what. Operators should not expect >35% of acetate electrons to be recovered as current; design energy balance and substrate dosing accordingly.

  • Performance The strain produced ammonia during anaerobic growth ('strong ammonia odor with pale green discoloration in old LB plates'), indicating amino acid fermentation, but no quantification of ammonia production or recovery potential was provided.

    So what. Ammonia recovery from this strain's fermentation may be feasible but requires quantification of production rates and pH/potential windows to prevent volatilization or inhibition.

Opportunity areas6

Specific gaps in this paper, with an experiment that would close each.

  • High No measurement of nitrate consumption rate, nitrite accumulation, or N2O production during anaerobic DRO degradation despite use of 10 mM nitrate as electron acceptor.

    Paper states 'anaerobic nitrate reduction' as a key trait and uses nitrate in degradation experiments (Figure 5B), but provides no kinetic data on nitrogen species transformation, making it impossible to assess denitrification efficiency or N2O risk.

    Try. Measure NO3⁻, NO2⁻, N2O, and NH4⁺ concentrations over time during anaerobic DRO degradation at 10 mM initial NO3⁻; vary initial NO3⁻ (5–20 mM) and DRO (4000–12000 mg/L) to map C/N ratio effects.

  • High No investigation of electrode potential (anode and cathode) during MFC operation or bioelectrochemical remediation; only external load (1000 Ω) and open-circuit voltage reported.

    Paper reports current and voltage but not the actual electrode potentials (vs. Ag/AgCl or SHE), which are critical for understanding electron transfer kinetics and predicting performance in different redox environments.

    Try. Measure anode and cathode potentials (vs. Ag/AgCl) during acetate and DRO degradation at varying external loads (10–10,000 Ω); correlate with current density and substrate consumption rate.

  • Medium No systematic variation of HRT (hydraulic retention time) or current density in bioelectrochemical cells; only fed-batch operation reported.

    Paper operates MFCs in fed-batch mode with substrate replacement when voltage drops to ≤10 mV, but does not explore continuous-flow or varying current-density regimes that would be relevant for field deployment.

    Try. Operate MFC in continuous-flow mode at HRTs of 12, 24, 48 h with acetate or DRO; measure current density, substrate removal, and coulombic efficiency as functions of HRT.

  • Medium No quantification of ammonia production or recovery during anaerobic amino acid fermentation, despite observation of strong ammonia odor.

    Text notes 'anaerobic fermentation of the amino acids' and 'strong ammonia odor,' but provides no molar yields, pH effects on volatilization, or potential for ammonia recovery in a bioelectrochemical context.

    Try. Quantify NH4⁺ production during anaerobic growth on amino acids (glycine, alanine, glutamate) at pH 6–8; measure volatilization loss and test ammonia recovery via pH swing or electrochemical stripping.

  • Medium No investigation of dissolved oxygen (DO) threshold or microaerobic conditions; only fully aerobic or fully anaerobic (N2/CO2 80:20) tested.

    Paper compares aerobic and anaerobic DRO degradation but does not explore the transition zone (DO 0.1–2 mg/L) where mixed metabolism or oxygen-limited denitrification might occur.

    Try. Degrade DRO at controlled DO levels (0, 0.5, 1, 2, 5 mg/L) and measure degradation rate, nitrate consumption, and N2O production.

  • Low No measurement of catholyte pH or its effect on denitrification or ammonia speciation; all experiments at pH 7 ± 0.2.

    Paper maintains fixed pH but does not explore how pH drift (common in MES cathodes) affects nitrogen cycling or ammonia recovery potential.

    Try. Operate MFC with varying initial pH (6.5–8.5) and measure pH drift, nitrate reduction rate, and ammonia volatilization over time.

Generated by MESSAI extraction pipeline · review against source PDF

02

Extracted values

Every value pulled from the paper, with its source, so each number can be checked against the text.

n = 32 extracted values

Select a citation to see the quote, page and confidence behind a value.

18 of 32 extracted rows modelable

  • 6 not canonicalised (no canonical slug)
  • 5 no SI value
  • 3 failed a physics check
ParameterValueUnitConfidenceSourceNotesModelable
Coulombic efficiency34.8%100%
extracted
"In acetate fed microbial fuel cells (MFCs), maximum current density of 273 ± 8 m…" · T=25°C, pH(an)=7, substrate=acetate, fed_batchModelable
Power Density113mW/m²100%
extracted
"In acetate fed microbial fuel cells (MFCs), maximum current density of 273 ± 8 m…" · T=25°C, pH(an)=7, substrate=acetate, fed_batchModelable
Current Density273mA/m²100%
extracted
"In acetate fed microbial fuel cells (MFCs), maximum current density of 273 ± 8 m…" · T=25°C, pH(an)=7, substrate=acetate, fed_batchModelable
Power Density113mW/m²95%
closed circuit with external load
"power density 113 ± 7 mW/m2" · pH(an)=7, substrate=acetate, steady_stateModelable
Current Density273mA/m²95%
closed circuit with external load
"maximum current density of 273 ± 8 mA/m2 (1000 Ω) was produced" · pH(an)=7, substrate=acetate, steady_stateModelable
Voltage414mV95%
dmm voltage measurement
"The maximum output range of voltage and current density were 414 ± 7 mV, 273 ± 8…" · pH(an)=7, substrate=acetate, steady_stateModelable
alkB Gene Similarity96%95%
blast sequence alignment
"Blastn searches in the GenBank database showed that the PCR product was similar …" · condition_hint=BLAST analysis to Burkholderia alkBExcluded: not canonicalised (no canonical slug)
Voltage145mV95%
dmm voltage measurement
"The maximum output range of voltage and current density were 145 ± 6 mV, 94 ± 6 …" · pH(an)=7, substrate=Reactive Black 5, steady_stateExcluded: failed a physics check
Current Density270mA/m²95%
closed circuit with external load
"After five refilling batches with a fresh substrate, the maximum current output …" · pH(an)=7, substrate=acetate, steady_stateModelable
Current Density94mA/m²95%
closed circuit with external load
"The maximum output range of voltage and current density were 145 ± 6 mV, 94 ± 6 …" · pH(an)=7, substrate=Reactive Black 5, steady_stateExcluded: failed a physics check
Electrode Surface Area6.99m²/g95%
bet isotherm
"The anode electrodes composed of carbon fiber brushes with wire titanium cores t…" · condition_hint=design parameter, before pre-treatment, electrode_material=carbon fiber brush with titanium coreExcluded: no SI value
16S rRNA Gene Sequence Length1,450bp95%
16s rrna gene sequencing
"An almost complete 16S rRNA gene sequence (1448 bp) was obtained for strain MK2" · condition_hint=phylogenetic analysisExcluded: not canonicalised (no canonical slug)
16S rRNA Sequence Similarity98%95%
blast sequence alignment
"From a BLAST analysis, the highest level of sequence similarity (98%) matched wi…" · condition_hint=BLAST analysis to ATCC 13637Excluded: not canonicalised (no canonical slug)
rubA Gene Similarity100%95%
blast sequence alignment
"Blastx alignments showed that this PCR product had 100% similarity to the corres…" · condition_hint=BLAST analysis to S. maltophilia rubAExcluded: not canonicalised (no canonical slug)
Azo Dye Removal59.3%90%
uv-visible spectroscopy
"Using RB5 concentration of 100 mg l−1 in MFC, 59.3 ± 1.25% was removed during th…" · pH(an)=7, substrate=Reactive Black 5, steady_stateModelable
Temperature Optimum30°C90%
culture growth observation
"The bacterial strain grew at temperatures ranging from 25 to 37°C at a neutral p…" · T=30°C, pH(an)=7Excluded: not canonicalised (no canonical slug)
Azo Dye Removal97.2%90%
uv-visible spectroscopy
"After 24 h, almost 97.2 ± 1.64% of RB5 was decolorized" · pH(an)=7, substrate=Reactive Black 5, steady_stateModelable
Operating Temperature37°C90%
culture growth observation
"The bacterial strain grew at temperatures ranging from 25 to 37°C" · T=37°C, pH(an)=7Modelable
Azo Dye Removal96.2%90%
uv-visible spectroscopy at 597 nm
"RB5 azoic dye was almost completely decolorized (96.23%) in 48 h by S. maltophil…" · T=25°C, pH(an)=7, substrate=Reactive Black 5, steady_stateModelable
Azo Dye Removal98%90%
uv-visible spectroscopy at 597 nm
"it took 72 h for nearly complete decolorization (97.99%) under aerobic condition…" · T=25°C, pH(an)=7, substrate=Reactive Black 5, steady_stateModelable
Operating Temperature25°C90%
culture growth observation
"The bacterial strain grew at temperatures ranging from 25 to 37°C" · T=25°C, pH(an)=7Modelable
Power Density99.9mW/m²90%
closed circuit with external load
"the reactors fed with azoic dye demonstrated the potential of generating current…" · pH(an)=7, substrate=Reactive Black 5, steady_stateExcluded: failed a physics check
Coulombic efficiency34.8%90%
cod removal calculation
"coulombic efficiency of 34.8%" · pH(an)=7, substrate=acetate, steady_stateModelable
Contaminant Removal Efficiency53%85%
gc-fid analysis
"cells started growing within 24 h with a rapid decrease in DRO concentration of …" · T=25°C, substrate=DRO, startupModelable
Contaminant Removal Efficiency88%85%
gc-fid analysis
"After 84 h, the strain reached as second peak of growth while the DRO degradatio…" · T=25°C, substrate=DRO, steady_stateModelable
Showing 25 of 32

Literature priors

Distribution

Against the literature

The author’s reported value (▼) sits on top of the literature distribution from MESS-Parameters. Values outside the band are flagged as outliers.

Coulombic efficiency34.8percent

Methodology

What was the system and how was it run

Methodology

Methodology

Strain MK2 was isolated from a hydrocarbon-fed MERS anode biofilm and characterized via 16S rRNA sequencing, biochemical assays (redox indicators, dye decolorization), and PCR-based detection of alkB and rubA genes. Aerobic and anaerobic DRO degradation (8000 mg/L) was monitored by GC-FID over 150 h and 14 days, respectively. Single-chamber MFCs (320 mL) with carbon fiber brush anodes and Pt-coated carbon cloth cathodes were operated in fed-batch mode at 1000 Ω external load; current, voltage, and coulombic efficiency were measured. Azo dye (RB5) decolorization was tracked spectrophotometrically at 595 nm.

Performance metrics

FieldValue
max power density7
coulombic efficiency34.8
citation count40

Operational parameters

FieldValue
substrate["acetate"]

Electrochemical data

FieldValue
max power density7
max current density8
coulombic efficiency34.8

Operating conditions

12 runs extracted
RunT°CpHanpHcatSubstrate[S]mg/LHRThModeR_extΩV_appVInoculum
v2-0f49689e39f03d6e257—Reactive Black 550—steady_state———
v2-128bb986e7bb299025——DRO8000—steady_state———
v2-202377c0cd2269bc—7—acetate1000—steady_state1000——
v2-41c56f4ad2f2a72825——DRO8000—startup———
v2-529d9c7a7b76820925——DRO8000—————
v2-5cd396422d68a042377————————
v2-6ba18e13778addf4257—acetate1000—fed_batch———
v2-841f15ec4c927218307————————
v2-a16127e0973b1c93—7—Reactive Black 5100—steady_state1000——
v2-b6dc6be2ddcc9c48257————————
v2-d41d8cd98f00b204——————————
v2-f586e9af22985397——————————

Outcomes

What was measured and what worked

Key takeaways

Coulombic efficiency

electrochemistry

34.8percent

Pipeline

Raw extractions, artifacts, quality signal

Extraction quality

honesty signal

Calibrate your trust in the extracted content against these signals — they're how the pipeline rated its own output for this paper.

Parameter completeness

50%

Fraction of expected parameters extracted

Reproducibility

28%

How reproducible the setup is from this paper alone

Data completeness

80%

Overall extraction coverage across fields

AI confidence

72%

Model self-reported confidence

Mean parameter confidence

88%

Average confidence across PaperParameter rows surfaced above

review against source PDF before citing · scores 0–1

03

Chart explorer

Move the inputs this paper used and see how the predicted outcome shifts.

04

Explore model

The reactor in 3D, with flow you can switch on and off.

05

AI insights

Contradictions, gaps and opportunities found by comparing this paper with the corpus.

06

Compare similar papers

The nearest papers by system, materials and organisms, with their outcomes side by side.

07

Source PDF

The paper as published.

loading 3D model…

Representative model, generic MFC

Representative MFC — matched on the paper’s system type only, not its reactor or geometry.

MFC
System
113milliwatts per square metre
Best result · Power density
best of 3
32
Extracted values
2016
Year

In this record

Organisms, parameters and materials this paper reports. Each links to its page.

Parameters · 1

Keywords

  • Bioremediation
  • Stenotrophomonas
  • Microbial fuel cell
  • AlkB
  • Hydrocarbon
  • Environmental chemistry

Cite

Krishnaveni Venkidusamy, M. Megharaj (2016). Identification of Electrode Respiring, Hydrocarbonoclastic Bacterial Strain Stenotrophomonas maltophilia MK2 Highlights the Untapped Potential for Environmental Bioremediation. Frontiers in Microbiology. https://doi.org/10.3389/fmicb.2016.01965

Open in lab for full controls, parameter editing, and template overlays.

Open in lab