Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation · MFC

Nutrient Removal Process and Cathodic Microbial Community Composition in Integrated Vertical-Flow Constructed Wetland – Microbial Fuel Cells Filled With Different Substrates

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

Interaktives 3D-ModellKI-angereichert· 78 %

Zusammenfassung

An integrated vertical-flow constructed wetland-microbial fuel cell system (CW-MFC), consisting of an up-flow chamber and a down-flow chamber, was constructed to treat synthetic sewage wastewater. The performance of CW-MFCs filled with different substrates [i.e., ceramsite (CM-A), quartz (CM-B), and zeolite (CM-C) granules] under various hydraulic retention times (HRTs, 7.6, 4.0, and 2.8 d) was evaluated. Efficient and stable nitrogen (N) and phosphorus (P) removals were observed in CM-A under different HRTs, while the voltage outputs of the CW-MFCs was greatly reduced as the HRTs decreased. With an HRT of 2.8 d, the ammonium (NH 4 + -N) and orthophosphate (PO 4 3- -P) removal efficiencies in CM-A were as high as 93.8 and 99.6%, respectively. Bacterial community analysis indicates that the N removal in the cathode area of CM-A could potentially benefit from the appearance of nitrifying bacteria (e.g., Nitrosomonas and Nitrospira ) and relatively high abundance of denitrifiers involved in simultaneous nitrification and denitrification (e.g., Hydrogenophaga , Zoogloea , and Dechloromonas ) and denitrifying sulfide removal (e.g., Thauera ). Additionally, the difference in N removal efficiency among the CW-MFCs could be partly explained by higher iron (Fe) content in milled ceramsite granules and higher abundance of denitrifiers with nitrate reduction and ferrous ions oxidation capabilities in CM-A compared with that in CM-B and CM-C. Efficient PO 4 3- -P removal in CM-A was mainly ascribed to substrate adsorption and denitrifying phosphorus (P) removal. Concerning the substantial purification performance in CM-A, ceramsite granules could be used to improve the nutrient removal efficiency in integrated vertical-flow CW-MFC.

KI-Zusammenfassung

78 % Konfidenz

This integrated vertical-flow constructed wetland–MFC (CW-MFC) study compared three substrates (ceramsite, quartz, zeolite) treating synthetic sewage at HRTs of 7.6, 4.0, and 2.8 d. Ceramsite (CM-A) achieved 93.8% NH₄⁺-N removal and 99.6% PO₄³⁻-P removal at 2.8 d HRT, driven by simultaneous nitrification–denitrification (SND) bacteria (Hydrogenophaga, Zoogloea, Dechloromonas) and denitrifying sulfide removal (Thauera). However, voltage output collapsed below 0.02 V at shorter HRTs, revealing a critical trade-off between nutrient removal and power generation.

Zentrale Erkenntnisse

  • Mechanismus Ceramsite substrate enabled 93.8% NH₄⁺-N removal at 2.8 d HRT despite low nitrifier abundance (Nitrosomonas 0.3%, Nitrospira 0.3%), via SND bacteria (Hydrogenophaga, Zoogloea, Dechloromonas) at 35.8% total denitrifier abundance in cathode.

    Was heißt das. Operators should prioritize substrate selection (ceramsite) and biofilm stratification over supplementary aeration to achieve SND in cathode; nitrifier abundance is not a reliable predictor of nitrification performance in this configuration.

  • Zielkonflikt Voltage output in up-flow chamber dropped from 120.3 mW/m³ at 7.6 d HRT to below 0.02 V (unmeasured power density) at 2.8 d HRT, while NH₄⁺-N removal remained high (93.8%), indicating decoupling of power generation from nutrient removal.

    Was heißt das. Do not use HRT reduction as a lever to improve both power and treatment simultaneously; select HRT based on treatment goal, not power output, or redesign electrode placement to maintain redox gradient at short HRTs.

  • Mechanismus Ceramsite's high Fe content (41,791 ± 452 mg/kg vs. quartz 8,096 ± 111 mg/kg, zeolite 219 ± 19 mg/kg) correlated with enrichment of Sphaerotilus (2.21% in CM-A vs. 0.09% in CM-B, 0.04% in CM-C) and ferrous-oxidizing denitrifiers (Azospira 11.17%, Zoogloea 2.96%, Dechloromonas 1.29%), suggesting autotrophic denitrification via Fe cycling.

    Was heißt das. Substrate selection should account for trace metal content (especially Fe) to enable autotrophic denitrification pathways; this may reduce dependence on organic carbon and improve N removal at low COD/N ratios.

  • Schwellenwert Effluent NOₓ⁻-N remained below 0.3 mg/L across all sampling ports and HRTs in all three systems, despite variable NH₄⁺-N removal, indicating complete denitrification to N₂ or N₂O (not measured) rather than nitrite/nitrate accumulation.

    Was heißt das. Monitor N₂O emissions in this system type, as complete denitrification to N₂ is not confirmed; the low NOₓ⁻-N may mask N₂O production, a potent greenhouse gas.

  • Mechanismus Ceramsite showed higher effluent SO₄²⁻-S than influent (Figure 3), while S²⁻-S was consumed in down-flow chamber (U2 to D1), consistent with denitrifying sulfide removal (DSR) by Thauera (7.72% in CM-A), coupling N and S cycling.

    Was heißt das. In systems with sulfide present, exploit DSR bacteria to simultaneously remove NOₓ⁻-N and S²⁻; monitor SO₄²⁻ production as a proxy for DSR activity and N removal efficiency.

Widersprüche2

Nur Konflikte, die die Publikation selbst zeigt, jeweils am Text geprüft.

  • Innerhalb der Publikation Power generation collapses while nutrient removal remains stable as HRT decreases

    Eine Seite

    Voltage output drops from 120.3 mW/m³ at 7.6 d HRT to below 0.02 V at 2.8 d HRT in CM-A

    “With an HRT of 7.6 d (H1), the average voltage outputs in both the up-flow and down-flow chambers in CM-A were higher than those in CM-B and CM-C... However, when the HRT was decreased to 4.0 d (H2) and 2.8 d (H3), low voltage outputs (below ”
    Andere Seite

    NH₄⁺-N removal efficiency in CM-A remains high at 93.8% at 2.8 d HRT, comparable to 95.8% at 7.6 d HRT

    “With an HRT of 2.8 d, the ammonium (NH4+-N) and orthophosphate (PO43−-P) removal efficiencies in CM-A were as high as 93.8 and 99.6%, respectively.”

    Einordnung der Autoren. Authors do not explicitly reconcile this; the decoupling suggests that nutrient removal is driven by bioelectrochemical and biological processes (SND, DSR) that are less dependent on the redox gradient needed for power generation, or that the electrode configuration (anode in down-flow, cathode in up-flow) is optimized for treatment rather than power.

  • Innerhalb der Publikation Quartz substrate shows lowest N removal but highest COD removal at short HRTs

    Eine Seite

    CM-B (quartz) achieves only 0.4% NH₄⁺-N removal at 2.8 d HRT but 91.8% COD removal

    “The lowest effluent COD concentrations in CM-B were observed among the three CW-MFCs under HRTs of 4.0 and 2.8 d.”
    Andere Seite

    CM-A (ceramsite) achieves 93.8% NH₄⁺-N removal at 2.8 d HRT but only 47.3% COD removal

    “With an HRT of 2.8 d, the ammonium (NH4+-N) and orthophosphate (PO43−-P) removal efficiencies in CM-A were as high as 93.8 and 99.6%, respectively.”

    Einordnung der Autoren. Authors attribute this to substrate-dependent microbial communities: quartz enriches sulfate-reducing bacteria (Desulfovibrio, Desulfomonile 2.2% in CM-B vs. 0.5% in CM-A) that consume organic carbon but do not support nitrification/denitrification; ceramsite enriches denitrifiers and iron-oxidizers that prioritize N removal over COD oxidation.

Ansatzpunkte6

Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.

  • Hoch N₂O emissions not measured; complete denitrification pathway (to N₂ vs. N₂O) unknown despite low NOₓ⁻-N effluent

    Effluent NOₓ⁻-N consistently <0.3 mg/L across all conditions, but paper does not report N₂O or N₂ production; SND and DSR bacteria can produce N₂O as a side product, especially under variable DO and pH

    Versuch. Measure N₂O and N₂ in headspace or dissolved phase using gas chromatography or isotope tracing (¹⁵N) across HRT range 2.8–7.6 d and DO gradient (2–4 mg/L observed); quantify N recovery balance

  • Hoch Cathode potential and current density not reported; electrochemical driving force for denitrification unknown

    Paper reports voltage output and power density but not cathode potential (vs. Ag/AgCl or SHE), current density, or polarization curves; these are critical to understanding whether denitrification is bioelectrochemical (electron transfer from cathode) or purely biological (organic carbon oxidation)

    Versuch. Measure cathode potential, anode potential, and current density at each HRT using potentiostat; correlate with denitrifier abundance and NOₓ⁻-N removal rate to quantify bioelectrochemical contribution

  • Mittel Influent COD/N ratio not varied; low organic carbon dependence of N removal not tested

    Synthetic wastewater has fixed COD/N ratio (~14 mg COD / mg N based on 243–262 mg/L COD and 16–18 mg/L NH₄⁺-N); paper claims autotrophic denitrification via Fe cycling but does not test whether N removal persists at lower COD/N ratios (e.g., <5)

    Versuch. Operate CM-A at HRT 2.8 d with COD/N ratios of 2, 5, 10, 14 (current); measure NH₄⁺-N removal, NOₓ⁻-N production, and denitrifier abundance to confirm autotrophic pathway

  • Mittel Ferrous/ferric iron concentrations not measured; Fe cycling mechanism inferred but not quantified

    Paper proposes that Sphaerotilus and Azospira/Zoogloea/Dechloromonas drive autotrophic denitrification via Fe²⁺ oxidation, but ferrous and ferric ion concentrations are not reported; SO₄²⁻-S increase in effluent is noted but not linked to Fe cycling

    Versuch. Measure dissolved Fe²⁺ and Fe³⁺ at sampling ports U4, U2, D1, D2 at HRT 2.8 d and 7.6 d using ICP-OES or colorimetric assay; correlate with NOₓ⁻-N removal and Sphaerotilus abundance

  • Mittel Catholyte pH range (8.0+) not explored; ammonia volatilization in up-flow chamber not quantified

    Effluent pH in CM-A up-flow chamber >8.0 (Supplementary Table S1); authors note this 'could contribute to the ammonia loss via volatilization' but do not measure NH₃ gas or quantify volatilization loss vs. biological removal

    Versuch. Operate CM-A at controlled pH (6.5, 7.0, 7.5, 8.0, 8.5) in up-flow chamber using buffer or acid/base dosing; measure NH₄⁺-N removal, effluent NH₃ (headspace), and nitrifier/denitrifier abundance to decouple volatilization from biological pathways

  • Mittel Substrate adsorption capacity for NH₄⁺ and PO₄³⁻ not quantified; contribution to removal efficiency unclear

    Paper states zeolite (CM-C) can adsorb NH₄⁺ at long HRT (7.6 d) and ceramsite shows 'substrate adsorption and denitrifying phosphorus removal' for PO₄³⁻, but adsorption isotherms, saturation time, and regeneration are not measured

    Versuch. Conduct batch adsorption tests on fresh and used ceramsite, quartz, zeolite granules with NH₄⁺ and PO₄³⁻ at pH 6–8; measure Langmuir/Freundlich parameters and compare to biological removal rates in columns

Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

n = 57 extrahierte Werte

Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.

44 von 57 extrahierten Zeilen modellierbar

  • 9 nicht kanonisiert (kein kanonischer Slug)
  • 4 widerspricht anderen Publikationen
ParameterWertEinheitKonfidenzQuelleAnmerkungenModellierbar
Power Density Volumetric120mW/m³90 %
extrahiert
"The average power densities in the up-flow chamber were 120.3, 11.3, and 14.2 mW/…" · pH(an)=8, substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=182.4hModellierbar
Power Density Volumetric11,3mW/m³90 %
extrahiert
"The average power densities in the up-flow chamber were 120.3, 11.3, and 14.2 mW/…" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=182.4hModellierbar
Power Density Volumetric14,2mW/m³90 %
extrahiert
"The average power densities in the up-flow chamber were 120.3, 11.3, and 14.2 mW/…" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=182.4hModellierbar
Ammonium Ion Concentration15,3mg/L90 %
extrahiert
"NH4+-N (mg/L): 4.0 d: 15.27 ± 1.30b,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Chemical Oxygen Demand (COD) Concentration87mg/L90 %
extrahiert
"COD (mg/L): 4.0 d: 87 ± 21a,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Ammonium-N Removed98,3%90 %
extrahiert
"NH4+-N removal efficiency (%): 4.0 d: 98.3" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Ammonium Ion Concentration0,75mg/L90 %
extrahiert
"NH4+-N (mg/L): 7.6 d: 0.75 ± 0.14a,A" · pH(an)=8, substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=182.4hModellierbar
Phosphate Ion Concentration0,35mg/L90 %
extrahiert
"PO43−-P (mg/L): 7.6 d: 0.35 ± 0.19a,A" · pH(an)=8, substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=182.4hModellierbar
Ammonium-N Removed95,8%90 %
extrahiert
"NH4+-N removal efficiency (%): 7.6 d: 95.8" · pH(an)=8, substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=182.4hModellierbar
Chemical Oxygen Demand (COD) Concentration18mg/L90 %
extrahiert
"COD (mg/L): 4.0 d: 18 ± 6b,A,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Phosphate Ion Concentration8,03mg/L90 %
extrahiert
"PO43−-P (mg/L): 4.0 d: 8.03 ± 0.26b,A" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Ammonium Ion Concentration11,9mg/L90 %
extrahiert
"NH4+-N (mg/L): 4.0 d: 11.94 ± 1.45c,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Ammonium Ion Concentration0,28mg/L90 %
extrahiert
"NH4+-N (mg/L): 4.0 d: 0.28 ± 0.14a,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Phosphate Ion Concentration0,03mg/L90 %
extrahiert
"PO43−-P (mg/L): 4.0 d: 0.03 ± 0.01a,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Chemical Oxygen Demand (COD) Removal92,6%90 %
extrahiert
"COD removal efficiency (%): 4.0 d: 92.6" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Chemical Oxygen Demand (COD) Removal62,9%90 %
extrahiert
"COD removal efficiency (%): 4.0 d: 62.9" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Phosphate Ion Concentration6,62mg/L90 %
extrahiert
"PO43−-P (mg/L): 4.0 d: 6.62 ± 0.28c,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Chemical Oxygen Demand (COD) Concentration90mg/L90 %
extrahiert
"COD (mg/L): 4.0 d: 90 ± 21a,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=96hModellierbar
Chemical Oxygen Demand (COD) Removal47,3%90 %
extrahiert
"COD removal efficiency (%): 2.8 d: 47.3" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=67.2hModellierbar
Phosphate Ion Concentration7,61mg/L90 %
extrahiert
"PO43−-P (mg/L): 2.8 d: 7.61 ± 0.19c,C" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=67.2hModellierbar
Ammonium Ion Concentration16,7mg/L90 %
extrahiert
"NH4+-N (mg/L): 2.8 d: 16.68 ± 1.51b,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=67.2hModellierbar
Chemical Oxygen Demand (COD) Concentration20mg/L90 %
extrahiert
"COD (mg/L): 2.8 d: 20 ± 5b,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=67.2hModellierbar
Chemical Oxygen Demand (COD) Concentration94mg/L90 %
extrahiert
"COD (mg/L): 2.8 d: 94 ± 11c,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=67.2hModellierbar
Chemical Oxygen Demand (COD) Removal91,8%90 %
extrahiert
"COD removal efficiency (%): 2.8 d: 91.8" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=67.2hModellierbar
Phosphate Ion Concentration0,03mg/L90 %
extrahiert
"PO43−-P (mg/L): 2.8 d: 0.03 ± 0.01a,B" · substrate=synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals), HRT=67.2hModellierbar
25 von 57 angezeigt

Methodik

Welches System und wie es betrieben wurde

Methodik

Methodology

Three integrated vertical-flow CW-MFCs (up-flow + down-flow chambers in series) were filled with ceramsite, quartz, or zeolite granules (4–8 mm) and operated at HRTs of 7.6, 4.0, and 2.8 d (hydraulic loading 0.54–1.47 L/d) for ~120 days. Synthetic wastewater (160 mg/L glucose + acetate, 90 mg/L NH₄Cl, 7 mg/L PO₄³⁻-P) was fed intermittently 3×/day. Electrodes (granular graphite anode in down-flow, air-cathode in up-flow) were connected via external resistors (1,000 Ω up-flow, 3,000 Ω down-flow). Water samples were collected weekly from 8 ports and analyzed for COD, NH₄⁺-N, NOₓ⁻-N, PO₄³⁻-P, S²⁻-S, SO₄²⁻-S, DO, and pH. Bacterial communities in cathode-region substrates were characterized by 16S rRNA gene sequencing (V3–V4 region, Illumina MiSeq).

Systemkonfiguration

FeldWert
reactor typeMES
chamber config2-chamber

Betriebsbedingungen

4 Läufe extrahiert
LaufT°CpHAnolytpHKatholytSubstrat[S]mg/LHRThModusR_extΩV_appVInokulum
v2-04b13f709c12315d———synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals)—96—1000——
v2-39b6580c29883568—8—synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals)—182.4—1000——
v2-3e68a144e5f3cca2———synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals)—67.2—1000——
v2-d10f0dc36471d705———synthetic sewage wastewater (glucose, acetate, phosphate, nitrogen, minerals)—182.4—1000——

Extraktionspipeline

Rohextraktionen, Artefakte, Qualitätssignal

Extraktionsqualität

Ehrlichkeitssignal

Bemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.

KI-Konfidenz

78 %

Vom Modell selbst angegebene Konfidenz

Mittlere Parameterkonfidenz

90 %

Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen

vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

07

Quell-PDF

Die Publikation, wie sie erschienen ist.

3D-Modell wird geladen …

Repräsentatives Modell, generisches MFC

Repräsentatives Modell: MFC – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.

MFC
System
96,6Prozent
Bestes Ergebnis · CSB-Entfernung
bester von 9
57
Extrahierte Werte
2020
Jahr

Schlagwörter

  • Denitrifying bacteria
  • Microbial fuel cell
  • Nitrosomonas
  • Nitrospira
  • Constructed wetland
  • Environmental chemistry

Zitieren

Fei Zhong, Chunmei Yu, Yanhong Chen et al. (2020). Nutrient Removal Process and Cathodic Microbial Community Composition in Integrated Vertical-Flow Constructed Wetland – Microbial Fuel Cells Filled With Different Substrates. Frontiers in Microbiology. https://doi.org/10.3389/fmicb.2020.01896

PubMed
32849471

Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.

Im Labor öffnen