Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation · MFC

The effect of ammonia concentration on the treatment of bio electrochemical leachate using MFCs technology

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

Interaktives 3D-ModellKI-angereichert· 72 %

Zusammenfassung

Microbial fuel cells (MFCs) have garnered attention in bio-electrochemical leachate treatment systems. The most common forms of inorganic ammonia nitrogen are ammonium ( NH 4 + ) and free ammonia. Anaerobic digestion can be inhibited in both direct (changes in environmental conditions, such as fluctuations in temperature or pH, can indirectly hinder microbial activity and the efficiency of the digestion process) and indirect (inadequate nutrient levels, or other conditions that indirectly compromise the microbial community's ability to carry out anaerobic digestion effectively) ways by both kinds. The performance of a double-chamber MFC system-composed of an anodic chamber, a cathode chamber with fixed biofilm carriers (carbon felt material), and a Nafion 117 exchange membrane is examined in this work to determine the impact of ammonium nitrogen ( NH 4 - N ) inhibition. MFCs may hold up to 100 mL of fluid. Therefore, the bacteria involved were analysed using 16S rRNA. At room temperature, with a concentration of 800 mg L -1 of ammonium nitrogen and 13,225 mg L -1 of chemical oxygen demand (COD), the study produced a considerable power density of 234 mWm -3 . It was found that NH 4 - N concentrations above 800 mg L -1 have an inhibitory influence on power output and treatment effectiveness. Multiple routes removed the most nitrogen ( NH 4 + -N: 87.11 ± 0.7%, NO 2 - N: 93.17 ± 0.2% and TN: 75.24 ± 0.3%). Results from sequencing indicate that the anode is home to a rich microbial community, with anammox (6%), denitrifying (6.4%), and electrogenic bacteria (18.2%) making up the bulk of the population. Microbial fuel cells can efficiently and cost-effectively execute anammox, a green nitrogen removal process, in landfill leachate.

KI-Zusammenfassung

72 % Konfidenz

Zentrale Erkenntnisse

  • Schwellenwert NH₄-N concentrations above 800 mg/L inhibited both power output and treatment effectiveness, establishing a critical threshold for this MFC configuration.

    Was heißt das. Operators should maintain influent NH₄-N below 800 mg/L or implement dilution/pre-treatment to avoid performance collapse in similar leachate-fed MFCs.

  • Mechanismus Multiple nitrogen removal pathways operated simultaneously: anammox (6% of anode community), denitrification (6.4%), and nitrification, with NO₂-N removal (93.17%) exceeding NH₄-N removal (87.11%), suggesting nitrite was the preferred intermediate.

    Was heißt das. Design cathode aeration and pH control to favor nitrite accumulation as an intermediate rather than complete nitrification to NO₃⁻, since anammox bacteria can couple NH₄⁺ + NO₂⁻ → N₂ directly.

  • Leistung Power density varied 3.9-fold across identically inoculated MFCs (161.81 vs 41.89 mW/m² for control), indicating biofilm colonization patterns and microbial community composition are stochastic and sensitive to minor environmental variations.

    Was heißt das. Replicate MFC experiments in triplicate minimum and consider inoculum standardization or pre-enrichment protocols to reduce inter-reactor variability in power output.

  • Zielkonflikt HRT of 4 h was chosen to accelerate biofilm development, but no comparison to longer HRTs was provided; the paper does not report whether nitrogen removal efficiency or N₂O accumulation changed with HRT.

    Was heißt das. Test HRT 8–24 h to determine whether longer residence time improves total nitrogen removal or shifts the NO₂⁻/NO₃⁻ balance without sacrificing power density.

Widersprüche1

Nur Konflikte, die die Publikation selbst zeigt, jeweils am Text geprüft.

  • Innerhalb der Publikation Paper claims anammox is the primary nitrogen removal pathway but reports anammox bacteria comprise only 6% of anode community, while denitrifiers are 6.4% and electrogenic bacteria 18.2%.

    Eine Seite

    'Microbial fuel cells can efficiently and cost-effectively execute anammox, a green nitrogen removal process, in landfill leachate' (Abstract)

    “Microbial fuel cells can efficiently and cost-effectively execute anammox, a green nitrogen removal process, in landfill leachate.”
    Andere Seite

    'anammox (6%), denitrifying (6.4%), and electrogenic bacteria (18.2%) making up the bulk of the population' (Abstract); 'In the anammox process, ammonium and nitrite are reacted directly to produce nitrogen gas N₂ (NH₄⁺-N, NO₂⁻–N → N₂)' (Introduction) but anammox is minority

    “anammox (6%), denitrifying (6.4%), and electrogenic bacteria (18.2%) making up the bulk of the population”

    Einordnung der Autoren. Authors emphasize anammox as the key process in the abstract and introduction but the 16S rRNA data shows anammox bacteria are a minor component (6%). The high NO₂⁻ removal (93.17%) is likely driven by heterotrophic denitrifiers (6.4%) and possibly electrogenic nitrifiers, not anammox. The paper does not reconcile this discrepancy; it may reflect that anammox is thermodynamically favorable but kinetically limited, or that the paper overstates anammox's role based on its presence rather than its activity.

Ansatzpunkte6

Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.

  • Hoch No comparison of nitrogen removal efficiency across different HRTs (tested only 4 h); unclear whether longer HRT (8–24 h) would improve TN removal or shift the NO₂⁻/NO₃⁻ balance.

    Paper states 'HRT was adjusted to 4 h' to accelerate biofilm development but provides no justification or sensitivity analysis. The 75.24% TN removal is lower than NH₄-N or NO₂-N removal alone, suggesting incomplete denitrification; longer HRT might allow more complete NO₃⁻ reduction.

    Versuch. Operate identical MFCs at HRT 4, 8, 12, 24 h; measure NH₄-N, NO₂-N, NO₃-N, TN removal and power density at each HRT to identify the trade-off between residence time and electricity generation.

  • Hoch No measurement of N₂O accumulation or emission; unclear whether the system produces N₂O as a byproduct of denitrification, which would reduce N₂ yield and create a greenhouse gas.

    Paper reports TN removal (75.24%) is lower than NH₄-N removal (87.11%), implying ~12% of nitrogen is unaccounted for; this could be NO₃⁻ accumulation or N₂O/NO emission. No gas chromatography or N₂O sensor data provided.

    Versuch. Measure headspace N₂O concentration via GC-ECD or real-time N₂O sensor during operation at 400–1600 mg/L NH₄-N; correlate N₂O yield with cathode potential, anode potential, and dissolved oxygen.

  • Hoch No systematic variation of cathode potential or anode potential; unclear how electrode potentials affect nitrification vs. denitrification balance and anammox activity.

    Paper operates MFC with fixed external resistance (1 kΩ) and does not report anode or cathode potentials. Anammox and denitrification have different redox requirements; varying cathode potential (e.g., via potentiostat) could shift the pathway.

    Versuch. Operate MFC at fixed cathode potentials (−0.2, −0.4, −0.6 V vs. Ag/AgCl) while measuring anode potential, power density, and nitrogen speciation (NH₄⁺, NO₂⁻, NO₃⁻, N₂O) to map the operating window for anammox vs. denitrification.

  • Mittel No measurement of dissolved oxygen (DO) in anode or cathode chambers; unclear whether the anode is truly anaerobic or if oxygen diffusion from the cathode affects nitrification and anammox.

    Paper states 'anode chamber was sparged with nitrogen gas to ensure anaerobic conditions' but does not report DO measurements. Anammox requires anoxia; if DO leaks into the anode, it would inhibit anammox and favor aerobic nitrification.

    Versuch. Measure DO in anode chamber via oxygen sensor during operation; if DO > 0.5 mg/L, test improved membrane sealing or anode chamber design to maintain strict anaerobiosis.

  • Mittel No variation of C/N ratio; unclear whether the 13,225 mg/L COD to 800 mg/L NH₄-N ratio (C/N ≈ 16.5 by mass) is optimal for anammox or whether lower C/N would favor anammox over heterotrophic denitrification.

    Paper uses a fixed leachate composition and does not test different C/N ratios. Anammox is autotrophic and does not require organic carbon; heterotrophic denitrifiers do. Lowering C/N might select for anammox.

    Versuch. Dilute leachate to achieve C/N ratios of 5, 10, 20, 40 (by mass); measure anammox and denitrifier abundance via qPCR and nitrogen removal pathways at each ratio.

  • Mittel No measurement of catholyte pH or its effect on nitrogen removal; unclear whether pH drift in the cathode (typically alkaline due to oxygen reduction) affects proton availability for nitrification or anammox.

    Paper states 'pH level was measured and adjusted once judged within the permissible range' but does not report pH values during operation or in the cathode chamber. Anammox and nitrification are pH-sensitive; alkaline pH favors free ammonia inhibition.

    Versuch. Monitor cathode and anode pH continuously; test pH control (e.g., buffer addition) to maintain anode pH 6.5–7.5 and measure impact on nitrogen removal and power density.

Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

n = 28 extrahierte Werte

Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.

19 von 28 extrahierten Zeilen modellierbar

  • 1 nicht kanonisiert (kein kanonischer Slug)
  • 8 kein SI-Wert
ParameterWertEinheitKonfidenzQuelleAnmerkungenModellierbar
Power Density162mWm⁻²90 %
extrahiert
"Figure 2 presents the results of the all the MFCs (MFC-A, MFC-B, MFC-C, MFC-D, M…" · T=28.5°C, pH(an)=6.88, substrate=landfill leachate, HRT=4hAusgeschlossen: kein SI-Wert
Power Density169mWm⁻²90 %
extrahiert
"steady-state power density 168.98 mWm−2 CE (15.62%)" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateAusgeschlossen: kein SI-Wert
Power Density283mWm⁻²90 %
extrahiert
"steady-state power density 283.38 mWm−2 CE (24.98%), 205.97 mWm−2 CE (18.87%), 1…" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateAusgeschlossen: kein SI-Wert
Power Density103mWm⁻²90 %
extrahiert
"steady-state power density 103.14 mWm−2 CE (12.03%)" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateAusgeschlossen: kein SI-Wert
Power Density206mWm⁻²90 %
extrahiert
"steady-state power density 232.38 mWm−2 CE (17.12%), 283.38 mWm−2 CE (24.98%), 2…" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateAusgeschlossen: kein SI-Wert
Power Density232mWm⁻²90 %
extrahiert
"Increase 600 mg L−1, 800 mg L−1, 1000 mg L−1, 1200 mg L−1, 1400 mg L−1 to 1600 m…" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateAusgeschlossen: kein SI-Wert
Power Density142mWm⁻²90 %
extrahiert
"steady-state power density 142.39 mWm−2 CE (14.62%)" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateAusgeschlossen: kein SI-Wert
Voltage479mV90 %
extrahiert
"with corresponding voltages 478.67 mV, 528.59 mV, 450.66 mV, 408.18 mV, 374.70 m…" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Coulombic efficiency12%90 %
extrahiert
"103.14 mWm−2 CE (12.03%)" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Coulombic efficiency17,1%90 %
extrahiert
"steady-state power density 232.38 mWm−2 CE (17.12%)" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Voltage319mV90 %
extrahiert
"with corresponding voltages 478.67 mV, 528.59 mV, 450.66 mV, 408.18 mV, 374.70 m…" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Coulombic efficiency15,6%90 %
extrahiert
"168.98 mWm−2 CE (15.62%)" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Coulombic efficiency14,6%90 %
extrahiert
"142.39 mWm−2 CE (14.62%)" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Voltage408mV90 %
extrahiert
"with corresponding voltages 478.67 mV, 528.59 mV, 450.66 mV, 408.18 mV, 374.70 m…" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Voltage451mV90 %
extrahiert
"with corresponding voltages 478.67 mV, 528.59 mV, 450.66 mV, 408.18 mV, 374.70 m…" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Coulombic efficiency25%90 %
extrahiert
"The highest power density recorded is 283.3846 mWm−2 CE (24.98%) at 800 mg L−1" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Voltage375mV90 %
extrahiert
"with corresponding voltages 478.67 mV, 528.59 mV, 450.66 mV, 408.18 mV, 374.70 m…" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Current Density2.950mA/m²90 %
extrahiert
"the highest power and current densities recorded were 855.31 mWm–2 and 2945.25 m…" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4ClModellierbar
Coulombic efficiency12%90 %
extrahiert
"MFC C had the highest COD removal efficiency of 80.10 ± 0.5% (CE 12.04%) at oper…" · T=28.5°C, pH(an)=6.88, substrate=landfill leachate, HRT=4hModellierbar
Voltage529mV90 %
extrahiert
"with the corresponding voltage 528.5993 mV" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Coulombic efficiency18,9%90 %
extrahiert
"205.97 mWm−2 CE (18.87%)" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4Cl, steady_stateModellierbar
Power Density855mWm⁻²90 %
extrahiert
"In Fig. 5A, the highest power and current densities recorded were 855.31 mWm–2 a…" · T=28.5°C, pH(an)=6.8, substrate=landfill leachate with added NH4ClAusgeschlossen: kein SI-Wert
Nitrogen Removal58,8%90 %
extrahiert
"MFC C cycle 4: 36–48 days operating time, TN removal of 58.76 as shown in Table …" · T=28.5°C, pH(an)=6.88, substrate=landfill leachate, HRT=4hModellierbar
Chemical Oxygen Demand (COD) Removal80,1%90 %
extrahiert
"MFC C had the highest COD removal efficiency of 80.10 ± 0.5% (CE 12.04%) at oper…" · T=28.5°C, pH(an)=6.88, substrate=landfill leachate, HRT=4hModellierbar
Ammonium-N Removed61,5%90 %
extrahiert
"At an influent concentration of 411 ± 6 mg L−1 at 90% leachate and 10% v/v inocu…" · T=28.5°C, pH(an)=6.88, substrate=landfill leachate, HRT=4hModellierbar
25 von 28 angezeigt

Methodik

Welches System und wie es betrieben wurde

Methodik

Methodology

Double-chamber H-type MFC (100 mL each chamber) with carbon felt electrodes, Nafion 117 PEM, and external 1 kΩ resistor. Anode fed with landfill leachate (13,225 mg/L COD, 411 mg/L NH₄-N baseline) at 4 h HRT; cathode aerated with air and filled with deionized water. Ammonia concentration varied 400–1600 mg/L NH₄-N via (NH₄)₂SO₄ addition. Voltage measured every 30 s; polarization curves recorded by varying external resistance. Nitrogen species (NH₄⁺-N, NO₂⁻-N, NO₃⁻-N, TN) measured via APHA methods. Anode biofilm analyzed via 16S rRNA sequencing. Experiments run in duplicate at 27–30 °C for 48 days after 38-day acclimatization.

Systemkonfiguration

FeldWert
reactor typeMFC
chamber config2-chamber

Betriebsbedingungen

4 Läufe extrahiert
LaufT°CpHAnolytpHKatholytSubstrat[S]mg/LHRThModusR_extΩV_appVInokulum
v2-2d6c26f978fbaa5928.56.88—landfill leachate—4—1000——
v2-47313c8efd19532028.56.8—landfill leachate with added NH4Cl——————
v2-9f641e138747b96b28.56.8—landfill leachate with added NH4Cl——steady_state1000——
v2-b528cbc08af5e36228.56.8—landfill leachate with added NH4Cl———1000——

Extraktionspipeline

Rohextraktionen, Artefakte, Qualitätssignal

Extraktionsqualität

Ehrlichkeitssignal

Bemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.

KI-Konfidenz

72 %

Vom Modell selbst angegebene Konfidenz

Mittlere Parameterkonfidenz

90 %

Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen

vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

07

Quell-PDF

Die Publikation, wie sie erschienen ist.

3D-Modell wird geladen …

Repräsentatives Modell, generisches MFC

Repräsentatives Modell: MFC – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.

MFC
System
2,95Ampere pro Quadratmeter
Bestes Ergebnis · Stromdichte
28
Extrahierte Werte
2023
Jahr

Schlagwörter

  • Microbial fuel cell
  • Anaerobic digestion
  • Leachate
  • Anammox
  • Nitrogen
  • Ammonia

Zitieren

Aliyu Ishaq, Mohd Ismid Mohd Said, Shamila Azman et al. (2023). The effect of ammonia concentration on the treatment of bio electrochemical leachate using MFCs technology. Environmental Science and Pollution Research. https://doi.org/10.1007/s11356-023-31472-x

PubMed
38151563

Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.

Im Labor öffnen