Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation · MFC

Treating Simulated Nitrate Pollution Groundwaterwith Different pH by Microbial Fuel Cell

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

Interaktives 3D-ModellKI-angereichert· 72 %

Zusammenfassung

Microbial fuel cell (MFC) is regarded as a promising technology to treat waste water and generate electricity simultaneously. MFCs usually work in the water-soluble medium, but the performance of the MFC which works in the porous medium is still unclear. Therefore, in this paper, a sand box was used to construct a dual-chamber MFC to investigate its performance. The MFC was used in porous medium to simulate the environment of groundwater, which was used to investigate the nitrate removal rate and the performance of electricity generation under different pH values. The performance of the MFC electrode was investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results showed that the maximum power density was 0.003 mW/m 3 (pH = 7.0) and the lowest nitrate concentration was 0.49 mg/L (pH = 8.5). The dominant microbial communities were Comamonadaceae bacterium, Xanthomonas axonopodis et al. Although the MFC was weak in electricity generation, it could offer valuable reference to further experiment.

KI-Zusammenfassung

72 % Konfidenz

This paper evaluates a dual-chamber MFC in porous medium (sand-filled) for treating simulated nitrate-contaminated groundwater across three pH values (5.5, 7.0, 8.5). The system achieved maximum power density of 0.003 mW/m² at pH 7.0 and lowest NO3⁻ concentration of 0.49 mg/L at pH 8.5, with best COD removal (62%) at neutral pH. Biofilm developed preferentially on the anode in solution medium rather than the cathode in porous medium, limiting overall performance. The work identifies pH as a critical control variable but reveals fundamental challenges in scaling MFCs to porous groundwater environments.

Zentrale Erkenntnisse

  • Schwellenwert Neutral pH (7.0) optimized both COD removal (lowest 190 mg/L vs 260 mg/L at pH 5.5) and sustained nitrate reduction, while acidic and alkaline conditions inhibited microbial activity and nitrate degradation.

    Was heißt das. Maintain anode pH near 7.0 in groundwater MFC designs; pH drift above 8.5 or below 5.5 will suppress both electron transfer and denitrification kinetics.

  • Mechanismus Porous medium cathode (sand-filled) accumulated few biofilms compared to solution-phase anode, reducing cathode electrochemical activity and increasing overall impedance (27,250–28,500 Ω mid-experiment vs 26,500–27,800 Ω end-experiment).

    Was heißt das. In in-situ groundwater MFCs, expect cathode biofilm limitation; consider pre-colonization, higher surface area, or biofilm-promoting cathode materials to reduce charge-transfer resistance.

  • Zielkonflikt Nitrate removal was spatially and temporally unstable across the five cathode chambers; holes 1–4 maintained high NO3⁻ (>70 mg/L), while hole 5 showed transient removal (0.49 mg/L at pH 8.5 on day 1) followed by rebound, and overflow outlet ranged 19.51–73.77 mg/L.

    Was heißt das. Porous-medium MFCs suffer from uneven electron distribution and mass-transfer limitations; design with shorter residence time, higher current density, or staged cathode chambers to sustain denitrification.

  • Mechanismus Anode electrochemical activity increased with reaction time (no redox peak mid-experiment, clear oxidation peak at −0.83 V end-experiment), indicating biofilm maturation enhanced electron transfer despite low absolute power output.

    Was heißt das. Allow 2+ weeks biofilm acclimation before assessing MFC performance; early-stage power measurements underestimate mature-system capacity.

  • Zielkonflikt Salt-bridge design and porous-medium geometry increased internal resistance (9,000–12,000 Ω) and suppressed electron transfer rate, yielding power density 0.003 mW/m² compared to 36 mW/m² in small single-chamber systems (Table 1).

    Was heißt das. For field deployment, replace salt bridges with ion-exchange membranes and minimize electrode separation; porous media inherently penalize power output—prioritize treatment over electricity recovery.

Widersprüche1

Nur Konflikte, die die Publikation selbst zeigt, jeweils am Text geprüft.

  • Innerhalb der Publikation pH 8.5 achieved lowest NO3⁻ concentration but worst COD removal, contradicting the expectation that optimal pH should improve all redox processes simultaneously.

    Eine Seite

    Lowest NO3⁻ concentration 0.49 mg/L at pH 8.5

    “the lowest nitrate concentration was 0.49 mg/L (pH = 8.5)”
    Andere Seite

    COD basically didn't degrade at pH 8.5; lowest COD 365 mg/L vs 190 mg/L at pH 7.0

    “the COD basically didn't degrade in the MFC whose pH was 8.5 in the running time of experiment, where the lowest COD concentration was 365 mg/L”

    Einordnung der Autoren. Authors attribute this to pH-dependent microbial activity: alkaline pH inhibits heterotrophic oxidation (COD removal) but may favor specific denitrifying pathways or abiotic reduction; however, the mechanism is not fully resolved. The instability of NO3⁻ removal at pH 8.5 (rebound after day 1) suggests the initial low value may reflect transient abiotic or non-sustained biological reduction rather than stable denitrification.

Ansatzpunkte6

Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.

  • Hoch No measurement of N2O or NO2⁻ accumulation during denitrification; paper only reports total NO3⁻ removal without speciation of end products.

    Denitrification can produce N2O (greenhouse gas) or accumulate NO2⁻ (toxic intermediate); without product analysis, cannot assess whether nitrate is truly mineralized to N2 or diverted to harmful byproducts. This is critical for environmental compliance.

    Versuch. Measure NO2⁻-N and N2O (headspace GC or dissolved probe) at each outlet hole and time point; correlate with cathode potential and current density to identify operating windows that suppress N2O.

  • Hoch No systematic variation of current density or cathode potential; all experiments run at fixed external resistance (1000 Ω) without exploring how applied voltage affects denitrification rate and selectivity.

    Cathode potential is the primary control on denitrification kinetics and product distribution in bioelectrochemical systems. Paper shows anode potential evolved (−0.83 V at end) but does not report or vary cathode potential, which is essential for optimizing NO3⁻ reduction.

    Versuch. Vary external resistance (100–10,000 Ω) or apply potentiostatic control (−0.4 to −0.8 V vs Ag/AgCl) at cathode; measure NO3⁻, NO2⁻, N2O, and current density to map the operating window for complete denitrification without N2O emission.

  • Mittel Hydraulic retention time (HRT) not reported; inlet flux 8.85 mL/min and cathode volume 0.5 L per chamber imply ~3.4 min HRT, but no sensitivity analysis across HRT range.

    HRT is a primary lever for controlling contact time between biofilm and substrate; short HRT (3.4 min) may explain poor and unstable NO3⁻ removal. Paper does not test whether longer HRT improves removal or whether there is a trade-off with throughput.

    Versuch. Vary inlet flux (2–20 mL/min) to span HRT from 1.5 to 15 min; measure NO3⁻ removal efficiency and outlet concentration as a function of HRT and current density.

  • Mittel No C/N ratio optimization; initial COD 500 mg/L and NO3⁻ 100 mg/L (C/N ≈ 5 by mass, or ~2.5 by molar ratio if assuming COD ≈ 1:1 with C) but no variation to test heterotrophic denitrification kinetics.

    Heterotrophic denitrification requires organic carbon; C/N ratio controls whether denitrification is carbon-limited or nitrogen-limited. Paper cites prior work on C/N effects (refs. 22–23) but does not explore this variable in porous medium.

    Versuch. Vary initial COD (100–1000 mg/L) at fixed NO3⁻ 100 mg/L to span C/N 1–10; measure NO3⁻ removal rate and final concentration to identify optimal C/N for porous-medium MFC.

  • Mittel Microbial community identified only from anode biofilm; no analysis of cathode biofilm or planktonic community in porous medium, limiting understanding of which organisms drive denitrification.

    Denitrification occurs at the cathode, but paper shows few biofilms there and does not sequence cathode community. Identified anode organisms (Comamonadaceae, Xanthomonas, Rhodobacter) are not known denitrifiers; true denitrifiers may be rare or absent.

    Versuch. Extract DNA from cathode biofilm and pore water at each hole; perform 16S rRNA gene sequencing and qPCR for denitrification genes (nirS, nirK, nosZ) to identify and quantify denitrifying populations and correlate with NO3⁻ removal.

  • Mittel No dissolved oxygen (DO) measurement in cathode chamber; porous medium may be aerobic or anaerobic depending on depth and flow, but DO is not reported.

    Denitrification requires anaerobic conditions; if cathode chamber is aerobic, NO3⁻ reduction may be suppressed or diverted to nitrification. DO control is essential for interpreting results and designing field systems.

    Versuch. Measure DO at inlet and outlet of each cathode chamber using optical probes; correlate with NO3⁻ removal and current density to determine whether anaerobic conditions are maintained and whether aeration affects performance.

Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

n = 17 extrahierte Werte

Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.

3 von 17 extrahierten Zeilen modellierbar

  • 11 nicht kanonisiert (kein kanonischer Slug)
  • 2 Physikprüfung nicht bestanden
  • 1 widerspricht anderen Publikationen
ParameterWertEinheitKonfidenzQuelleAnmerkungenModellierbar
Power Density0,00316mW/m²90 %
extrahiert
"the maximum power density was 0.00316 mW/m2, the corresponding current density w…" · pH(an)=8.5, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: Physikprüfung nicht bestanden
corresponding current density0,141mA/m²90 %
extrahiert
"the maximum power density was 0.00316 mW/m2, the corresponding current density w…" · pH(an)=8.5, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
highest voltage130mV90 %
extrahiert
"At the pH = 8.5, the voltage continuously increased to 130 mV after 12 hours and…" · pH(an)=8.5, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Power Density0,003mW/m²90 %
extrahiert
"the maximum power density was 0.003 mW/m2, the corresponding current density was…" · pH(an)=7, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: Physikprüfung nicht bestanden
corresponding current density0,12mA/m²90 %
extrahiert
"the maximum power density was 0.003 mW/m2, the corresponding current density was…" · pH(an)=7, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
highest voltage70,8mV90 %
extrahiert
"At the pH = 7.0, the voltage was small and basically kept at about 40 mV. The hi…" · pH(an)=7, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
corresponding current density0,087mA/m²90 %
extrahiert
"the maximum power density was 0.00159 mW/m2, the corresponding current density w…" · pH(an)=5.5, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Power Density0,00159mW/m²90 %
extrahiert
"The optimum internal resistance of the MFC whose pH is 5.5 was 12000Ω, the maxim…" · pH(an)=5.5, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: widerspricht anderen Publikationen
Internal Resistance9.000Ω90 %
extrahiert
"The optimum internal resistance of the MFC whose pH is 8.5 was 9000Ω" · pH(an)=8.5, substrate=simulated nitrate-polluted groundwaterModellierbar
Internal Resistance12.000Ω90 %
extrahiert
"the optimum internal resistance of the MFC whose pH was 7.0 was 12000Ω" · pH(an)=7, substrate=simulated nitrate-polluted groundwaterModellierbar
lowest chemical oxygen demand (COD) concentration365mg/L90 %
extrahiert
"the COD basically didn't degrade in the MFC whose pH was 8.5 in the running time…" · pH(an)=8.5, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
lowest nitrate concentration at hole 53,18mg/L90 %
extrahiert
"the lowest concentrations were 3.18 mg/L and 0.49 mg/L respectively" · pH(an)=5.5, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Internal Resistance12.000Ω90 %
extrahiert
"The optimum internal resistance of the MFC whose pH is 5.5 was 12000Ω" · pH(an)=5.5, substrate=simulated nitrate-polluted groundwaterModellierbar
lowest chemical oxygen demand (COD) concentration260mg/L90 %
extrahiert
"the lowest COD concentration in the MFC anode solution whose pH value was 5.5 wa…" · pH(an)=5.5, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
lowest nitrate concentration at hole 50,49mg/L90 %
extrahiert
"the lowest concentrations were 3.18 mg/L and 0.49 mg/L respectively" · pH(an)=8.5, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
lowest chemical oxygen demand (COD) concentration190mg/L90 %
extrahiert
"the lowest COD concentration in the anode solution was 190 mg/L" · pH(an)=7, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
lowest nitrate concentration at overflow tank outlet19,5mg/L90 %
extrahiert
"The lowest concentration was 19.51 mg/L, but then increased again. The end value…" · pH(an)=7, substrate=simulated nitrate-polluted groundwaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)

Methodik

Welches System und wie es betrieben wurde

Methodik

Methodology

A dual-chamber MFC was constructed with five sand-filled cathode chambers (0.5 L each, 120 cm² carbon cloth electrode) connected via salt bridges to a single anode chamber (9 L, 176 cm² carbon cloth electrode) containing simulated groundwater (100 mg/L NO3⁻, 500 mg/L COD). Three pH conditions (5.5, 7.0, 8.5) were tested in parallel at fixed external resistance (1000 Ω) and inlet flux (8.85 mL/min) for 120 h. Samples were collected every 4 h from each outlet and analyzed for NO3⁻-N, NO2⁻-N, NH4⁺-N, and COD. Electrodes were characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) at mid-experiment and end-experiment. Biofilm morphology was imaged by SEM and microbial community composition determined by DGGE and 16S rRNA gene sequencing.

Systemkonfiguration

FeldWert
reactor typeMFC
chamber config2-chamber

Betriebsbedingungen

3 Läufe extrahiert
LaufT°CpHAnolytpHKatholytSubstrat[S]mg/LHRThModusR_extΩV_appVInokulum
v2-7a11eae3554c6785—8.5—simulated nitrate-polluted groundwater———1000——
v2-ee80723e337d310c—7—simulated nitrate-polluted groundwater———1000——
v2-fe8290f91ae3ab10—5.5—simulated nitrate-polluted groundwater———1000——

Extraktionspipeline

Rohextraktionen, Artefakte, Qualitätssignal

Extraktionsqualität

Ehrlichkeitssignal

Bemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.

KI-Konfidenz

72 %

Vom Modell selbst angegebene Konfidenz

Mittlere Parameterkonfidenz

90 %

Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen

vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

07

Quell-PDF

Die Publikation, wie sie erschienen ist.

3D-Modell wird geladen …

Repräsentatives Modell, generisches MFC

Repräsentatives Modell: MFC – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.

MFC
System
0,00Milliwatt pro Quadratmeter
Bestes Ergebnis · Leistungsdichte
bester von 3
17
Extrahierte Werte
2020
Jahr

Schlagwörter

  • Groundwater
  • Nitrate
  • Groundwater pollution
  • Pollution
  • Microbial fuel cell
  • Environmental chemistry

Zitieren

Shaohua Chen, Wenliang Chen, Xiufang Wang et al. (2020). Treating Simulated Nitrate Pollution Groundwaterwith Different pH by Microbial Fuel Cell. Polish Journal of Environmental Studies. https://doi.org/10.15244/pjoes/118425

Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.

Im Labor öffnen