Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation · MFC

Influence of microbial fuel cell integration on organic matter and nutrient removal in a constructed wetland for wastewater treatment

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

Interaktives 3D-ModellKI-angereichert· 72 %Substrat ·real wastewaterWastewater TreatmentPower Generation

Zusammenfassung

The combination of constructed wetlands (CWs) and microbial fuel cells (MFCs) has emerged in recent years with the purpose of enhancing wastewater treatment efficiency of CWs while simultaneously generating electricity. Taking the above into account, the aim of this study is to evaluate the influence of MFC integration on organic matter and nutrient removal in a constructed wetland. The results showed that NH4+-N concentration reduced from 66.5 ±9.4 at day 0 (influent) to 4.5±0.4 mg/L and 7.03±3.93mg/L for the integrated system and control system, respectively. In terms of the NH4+-N removal efficiency, an enhancement of the nitrification rate (Ni) was observed when MFC was integrated in VSSF (120.6±1.5 mg/m² d for control system and 166.8±2.3 mg/m² d for integrated system). The average COD removal efficiencies were 89.36±2.67% and 94.2±5.9% in the CW and CW-MFC, respectively, obtaining a voltage close to 250 mV. The maximum power density generated was 4.75 mW/m². In conclusion, the removal efficiencies of COD and NH4+-N in VSSF were 89.4 and 88.4%, respectively, while in CW-MFC were 94.3 and 93.2 %. Therefore, the integrating of a MFC into CW does not have adverse effects on the capacity of the CW to efficiently domestic wastewater treatment.

KI-Zusammenfassung

72 % Konfidenz

This laboratory-scale study integrated a microbial fuel cell (MFC) into a vertical subsurface flow constructed wetland (VSSF) treating synthetic domestic wastewater. The MFC-integrated system enhanced NH₄⁺-N removal efficiency to 93–96% (vs. 89–91% in control) and nitrification rate to 166.8±2.3 mg/m² d (vs. 120.6±1.5 mg/m² d), while also improving COD removal to 94% and generating up to 10.32 mW/m² power density at OLR 28 COD g/m² d. The authors conclude MFC integration does not compromise treatment performance and simultaneously recovers energy.

Zentrale Erkenntnisse

  • Mechanismus Nitrification rate increased 38% when MFC was integrated (166.8±2.3 mg/m² d) versus control (120.6±1.5 mg/m² d), suggesting the electrochemical gradient enhanced aerobic nitrification.

    Was heißt das. Operators should consider MFC integration as a mechanism to boost nitrification capacity without adding external aeration, though the electrochemical mechanism driving this remains unexplained.

  • Zielkonflikt Power density increased 117% when OLR doubled from 12 to 24 COD g/m² d (4.75 to 10.32 mW/m²), but coulombic efficiency dropped from 1.80% to 1.60%, indicating energy recovery scales with substrate but electron recovery does not.

    Was heißt das. Higher OLR favors power output but wastes most electrons; operators must choose between maximizing electricity or maximizing treatment efficiency, not both.

  • Schwellenwert NH₄⁺-N removal efficiency improved with HRT across all stages in both systems, with VSSF-MFC consistently 3–7 percentage points higher than VSSF.

    Was heißt das. Longer residence time is essential for nitrification; MFC integration amplifies this benefit, suggesting the cathode provides additional oxidizing capacity or oxygen availability.

  • Schwellenwert COD concentrations below 1000 mg/L maintain dissolved O₂ availability at the cathode, enabling reduction reactions; above this threshold, organic matter may reach the cathode and consume O₂.

    Was heißt das. Design cathode compartments to exclude high-COD influent or operate at OLR ≤24 COD g/m² d to preserve cathode function and nitrification.

Ansatzpunkte6

Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.

  • Hoch No measurement of NO₃⁻, NO₂⁻, or N₂O in effluent or at different depths; nitrification rate is inferred from NH₄⁺ removal but nitrogen speciation is absent.

    The paper reports nitrification rate enhancement but provides no evidence that NO₃⁻ is the end product or whether NO₂⁻ or N₂O accumulates, especially under the electrochemical gradient.

    Versuch. Measure NO₃⁻-N, NO₂⁻-N, and N₂O at anode, cathode, and effluent zones across OLR 12–28 COD g/m² d to map nitrogen speciation and identify denitrification or N₂O production.

  • Hoch Cathode potential and anode potential are not reported; only external resistance (1000 Ω) and open circuit voltage are given.

    Understanding the electrochemical window (cathode potential range, anode potential) is essential to predict nitrification enhancement and avoid inhibitory potentials or oxygen depletion.

    Versuch. Measure cathode and anode potentials vs. Ag/AgCl reference electrode during Stages I and II; correlate with nitrification rate and dissolved O₂ at cathode.

  • Hoch Dissolved oxygen (DO) concentration is not measured in the cathode or anode compartments; only inferred from COD breakthrough.

    DO is the critical driver of nitrification and cathode reduction; without DO data, the mechanism of nitrification enhancement cannot be validated.

    Versuch. Profile DO at 5 cm depth intervals in both anode and cathode zones during Stage II; correlate with NH₄⁺-N removal and nitrification rate.

  • Mittel No investigation of C/N ratio effect; influent C/N is not calculated or varied.

    Nitrification and denitrification are both C/N-dependent; the paper uses fixed glucose and acetate concentrations but does not explore whether C/N ratio limits nitrification or enables denitrification.

    Versuch. Vary influent C/N ratio (e.g., 5:1, 10:1, 20:1) at constant OLR 24 COD g/m² d and measure NH₄⁺-N removal, NO₃⁻-N, and nitrification rate.

  • Mittel Catholyte pH is not reported; only influent and effluent pH are implied to be neutral.

    Nitrification is pH-sensitive (optimum ~7–8); cathode pH can drift due to electrochemical reactions, potentially inhibiting nitrification or promoting N₂O.

    Versuch. Monitor catholyte pH continuously during Stage II and correlate with nitrification rate; test pH buffering or control strategies.

  • Mittel HRT is held constant at 10 d in Stages I and II; no systematic variation of HRT to find the minimum residence time for nitrification in the MFC-integrated system.

    Figure 1 shows HRT improves removal, but the paper does not identify the operating window (minimum HRT) where nitrification remains efficient.

    Versuch. Reduce HRT from 10 d to 5, 3, and 2 d at OLR 24 COD g/m² d and measure nitrification rate and NH₄⁺-N removal efficiency to define the threshold.

Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

n = 52 extrahierte Werte

Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.

11 von 49 extrahierten Zeilen modellierbar

  • 29 nicht kanonisiert (kein kanonischer Slug)
  • 9 kein SI-Wert
ParameterWertEinheitKonfidenzQuelleAnmerkungenModellierbar
Substratewastewater—80 %
llm
Voltage250mV80 %
llm
abstract
Maximum power density4,75mW/m²80 %
llm
Chemical Oxygen Demand (COD) Removal×285,4%100 %
extrahiert
"the removal efficiencies of COD and NH4+-N in VSSF were 85.4 and 88.4%, respecti…"Modellierbar
Chemical Oxygen Demand (COD) Removal×294,3%100 %
extrahiert
"the removal efficiencies of COD and NH4+-N in VSSF were 85.4 and 88.4%, respecti…"Modellierbar
Nitrification rate167mg/m² d95 %
extrahiert
"166.8±2.3 mg/m2 d for integrated system" · substrate=domestic wastewaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
NH₄ n concentration7,03mg/L95 %
extrahiert
"to 4.5±0.4 mg/L and 7.03±3.93mg/L for the integrated system and control system, …" · substrate=domestic wastewaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
NH₄ n concentration4,5mg/L95 %
extrahiert
"to 4.5±0.4 mg/L and 7.03±3.93mg/L for the integrated system and control system, …" · substrate=domestic wastewaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Nitrification rate121mg/m² d95 %
extrahiert
"120.6±1.5 mg/m2 d for control system" · substrate=domestic wastewaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
NH₄ n concentration66,5mg/L95 %
extrahiert
"NH4+-N concentration reduced from 66.5 ±9.4 at day 0 (influent)" · substrate=domestic wastewaterAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical Oxygen Demand (COD) Removal85,4%95 %
extrahiert
"The average COD removal efficiencies were 85.36±2.67% and 94.2±5.9% in the CW an…" · substrate=domestic wastewaterModellierbar
Chemical Oxygen Demand (COD) Removal94,2%95 %
extrahiert
"The average COD removal efficiencies were 85.36±2.67% and 94.2±5.9% in the CW an…" · substrate=domestic wastewaterModellierbar
Chemical oxygen demand (COD) removal efficiency89 +8,6 (std_dev)%90 %
cod (influent 531+/-4.7, effluent 55+/-3.5 mg/l)
"VSSF MFC I 531 +/-4.7 55 +/-3.5 89 +/-8.6" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.12 g/L) + acetate (0.12 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) removal efficiency80 +3,7 (std_dev)%90 %
cod (influent 471+/-7.5, effluent 56+/-2.1 mg/l)
"VSSF I 471 +/-7.5 56 +/-2.1 80 +/-3.7" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.12 g/L) + acetate (0.12 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) removal efficiency94 +7 (std_dev)%90 %
cod (influent 967+/-7.0, effluent 102+/-6.6 mg/l)
"VSSF MFC II 967 +/-7.0 102 +/-6.6 94 +/-7.0" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.32 g/L) + acetate (0.32 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) effluent55 +3,5 (std_dev)mg/L90 %
cod
"VSSF MFC I ... Final 55 +/-3.5" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.12 g/L) + acetate (0.12 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) effluent56 +2,1 (std_dev)mg/L90 %
cod
"VSSF I ... Final 56 +/-2.1" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.12 g/L) + acetate (0.12 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) effluent102 +6,6 (std_dev)mg/L90 %
cod
"VSSF MFC II ... Final 102 +/-6.6" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.32 g/L) + acetate (0.32 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) effluent65 +0,5 (std_dev)mg/L90 %
cod
"VSSF II ... Final 65 +/-0.5" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.32 g/L) + acetate (0.32 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Open circuit voltage440mV90 %
open circuit voltage
"Open circuit voltage mV 357.36 440.44" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.32 g/L) + acetate (0.32 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Current density97,7mA/m²90 %
current density
"Current density mA/m2 53.26 97.67" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.32 g/L) + acetate (0.32 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Internal resistance201ohm90 %
polarization / internal resistance
"Internal resistance Ohms 293.48 200.77" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.32 g/L) + acetate (0.32 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Open circuit voltage357mV90 %
open circuit voltage
"Open circuit voltage mV 357.36 440.44" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.12 g/L) + acetate (0.12 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Internal resistance293ohm90 %
polarization / internal resistance
"Internal resistance Ohms 293.48 200.77" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.12 g/L) + acetate (0.12 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Current density53,3mA/m²90 %
current density
"Current density mA/m2 53.26 97.67" · substrate=Synthetic solution simulating pretreated domestic wastewater; glucose (0.12 g/L) + acetate (0.12 g/L) as carbon source, HRT=240h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
25 von 45 angezeigt

Methodik

Welches System und wie es betrieben wurde

Methodik

Methodology

Two identical vertical subsurface flow constructed wetland columns (0.15 m × 0.15 m × 0.7 m) were operated in parallel: one control (VSSF) with gravel–zeolite–gravel layers, and one with integrated MFC (VSSF-MFC) featuring granular activated carbon anodes and cathodes at 10 cm depth intervals, connected via 1000 Ω external resistance. Both were planted with Schoenoplectus californicus and fed synthetic domestic wastewater (glucose + acetate, 250–1000 mg/L COD) at HRT 7–10 d and OLR 7–28 COD g/m² d across three operational stages. Effluent COD, NH₄⁺-N, and electrical parameters (OCV, power density, coulombic efficiency) were measured.

Systemkonfiguration

FeldWert
reactor typeMES
chamber config2-chamber

Leistungskennzahlen

FeldWert
max power density4.75

Betriebsparameter

FeldWert
substrate["wastewater"]

Elektrochemische Daten

FeldWert
max power density4.75

Betriebsbedingungen

15 Läufe extrahiert
LaufT°CpHAnolytpHKatholytSubstrat[S]mg/LHRThModusR_extΩV_appVInokulum
baseline———domestic wastewater——————
baseline #2———domestic wastewater——————
baseline #3———domestic wastewater——————
cma:VSSF_control_stageI———Synthetic solution simulating pretreated domestic wastewater; glucose (0.12 g/L) + acetate (0.12 g/L) as carbon source500240continuous———
cma:VSSF_control_stageII———Synthetic solution simulating pretreated domestic wastewater; glucose (0.32 g/L) + acetate (0.32 g/L) as carbon source1000240continuous———
cma:VSSF-MFC_stageI———Synthetic solution simulating pretreated domestic wastewater; glucose (0.12 g/L) + acetate (0.12 g/L) as carbon source500240continuous1000——
cma:VSSF-MFC_stageII———Synthetic solution simulating pretreated domestic wastewater; glucose (0.32 g/L) + acetate (0.32 g/L) as carbon source1000240continuous1000——
control_CW———domestic wastewater——————
control_CW #2———domestic wastewater——————
control_CW #3———domestic wastewater——————
integrated_CW_MFC———domestic wastewater——————
integrated_CW_MFC #2———domestic wastewater——————
integrated_CW_MFC #3———domestic wastewater——————
v2-6ba40009484093f9———domestic wastewater——————
v2-b1dc4e52e32f2f28———domestic wastewater——————

Ergebnisse

Was gemessen wurde und was funktioniert hat

Elektrochemie

12 Konstanten
ElektrodeReaktionParameterWertEinheitKonf.
anode—internal_resistance200.77Ohms100 %
anode—internal_resistance293.48Ohms100 %
anode—internal_resistance293.48Ohms100 %
anode—internal_resistance200.77Ohms100 %
anode—internal_resistance200.77Ohms100 %
anode—internal_resistance293.48Ohms100 %
anode—ocv_open_circuit_voltage440.44Millivolt100 %
anode—ocv_open_circuit_voltage357.36Millivolt100 %
anode—ocv_open_circuit_voltage440.44Millivolt100 %
anode—ocv_open_circuit_voltage357.36Millivolt100 %
anode—ocv_open_circuit_voltage440.44Millivolt100 %
anode—ocv_open_circuit_voltage357.36Millivolt100 %

Extraktionspipeline

Rohextraktionen, Artefakte, Qualitätssignal

Extraktionsqualität

Ehrlichkeitssignal

Bemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.

Parametervollständigkeit

63 %

Anteil der erwarteten Parameter, die extrahiert wurden

Datenvollständigkeit

80 %

Gesamtabdeckung der Extraktion über alle Felder

KI-Konfidenz

72 %

Vom Modell selbst angegebene Konfidenz

Mittlere Parameterkonfidenz

84 %

Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen

vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

07

Quell-PDF

Die Publikation, wie sie erschienen ist.

3D-Modell wird geladen …

Repräsentatives Modell: Einkammer-MFC mit Luftkathode

Repräsentatives Modell: Einkammer-MFC mit Luftkathode – zugeordnet anhand der berichteten Konfiguration der Publikation, nicht ihrer genauen Geometrie.

MFC
System
4,75Milliwatt pro Quadratmeter
Bestes Ergebnis · Leistungsdichte
bester von 3
52
Extrahierte Werte
2022
Jahr

In diesem Datensatz

Organismen, Parameter und Materialien, die diese Publikation berichtet. Jeder Eintrag verweist auf seine Seite.

Organismen · 1

  • mixed culture

Materialien · 1

Schlagwörter

  • Microbial fuel cell
  • Wastewater
  • Constructed wetland
  • Organic matter
  • Nutrient
  • Sewage treatment

Zitieren

Thais Gonzalez, Juan Pablo Miranda, Gladys Vidal (2022). Influence of microbial fuel cell integration on organic matter and nutrient removal in a constructed wetland for wastewater treatment. Global NEST International Conference on Environmental Science & Technology. https://doi.org/10.30955/gnc2019.00488

Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.

Im Labor öffnen