Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.
Publikation · MFC
Simultaneous Generation of Bioelectricity and Treatment of Swine Wastewater in a Microbial Fuel Cell
Zusammenfassung
Was die Publikation berichtet, in ihren eigenen Worten.
Zusammenfassung
This study aimed at the simultaneous treatment of wastewater obtained from swine and generation of bioenergy in form of electricity from the energy stored in the organic component of the wastewater. The Open circuit voltage, current, power density and microbiological and physicochemical parameters were monitored. An initial Open circuit voltage of 516mV, Current of 0.29mA, and Power density of 32.74mW/m 2 were recorded, which increased to give maximum Open Circuit Voltages of 836mV, Current of 0.49mA, and Power density of 88.45mW/m 2 . The results revealed that The Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD), Organic carbon, Total Soluble solids (TSS), Ammonia, Ammonium and Ammonium-Nitrogen all showed percentage decrease of 85.92%, 51.74%, 78.16%, 98.87%, 55.87%, 55.79% and 55.90% respectively while parameters such as Total Dissolved Solids (TDS), Nitrate, Nitrate-Nitrogen, Phosphates, Phosphorus and Orthophosphates however increased after treatment to give a percentage increase of -273.60%, -131.65%, -134.85%, -168.77%, -159.26%, and -157.03% respectively. Bacteria isolates identified at the biofilms on the anode were Corynebacterium specie , Bacillus specie , Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa and Streptococcus faecalis . The results from this study further exacerbate the Bioelectricity production as well as wastewater treatment potentials of the Microbial Fuel Cell technology.
KI-Zusammenfassung
45 % KonfidenzThis study operated a single-chamber microbial fuel cell (MFC) on swine wastewater, achieving power density up to 88.45 mW/m² and removing 85.92% COD and 55.90% ammonium-nitrogen. However, the system produced a dramatic increase in nitrate-nitrogen (−134.85%, interpreted as accumulation) and nitrite, indicating incomplete nitrogen removal and potential nitrification without coupled denitrification. No cathode potential, anode potential, current density, HRT, C/N ratio, dissolved oxygen, or pH control data are reported, limiting understanding of the operating window and nitrogen cycling mechanisms.
Zentrale Erkenntnisse
Mechanismus Ammonia removal of 55.90% (ammonium-nitrogen basis) occurred simultaneously with nitrate-nitrogen accumulation of 134.85%, indicating nitrification proceeded but denitrification was absent or incomplete.
Was heißt das. Single-chamber MFC design without anaerobic cathode control or external electron acceptor management cannot achieve net nitrogen removal; a two-chamber system or cathode potential control is required to suppress nitrification or enable denitrification.
Zielkonflikt Power density increased from 32.74 to 88.45 mW/m² over the operating period, but no correlation with nitrogen removal efficiency or accumulation rate is provided.
Was heißt das. Operators cannot predict whether higher power output will improve or worsen nitrogen cycling; explicit measurement of anode/cathode potential and current density against nitrogen species is needed.
Schwellenwert Nitrite accumulation is mentioned qualitatively but not quantified; no N2O or other gaseous nitrogen loss is reported.
Was heißt das. Test for nitrite and N2O accumulation at the operating potentials and current densities used; these are critical for assessing environmental risk and nitrogen balance closure.
Ansatzpunkte6
Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.
Hoch Measure and control anode potential and cathode potential separately; no potentials are reported, making it impossible to determine whether the cathode was aerobic (favoring nitrification) or anaerobic (enabling denitrification).
Nitrogen cycling outcome (nitrification vs. denitrification) is directly controlled by electrode potential and dissolved oxygen; the paper reports only OCV and current, not working potentials.
Versuch. Operate at fixed anode potential (e.g., −0.2 V vs. Ag/AgCl) and cathode potential (e.g., −0.6 V for denitrification or +0.2 V for nitrification) and measure NO3-N, NO2-N, and N2O at each condition.
Hoch Quantify and control dissolved oxygen in the cathode chamber or bulk solution; no DO measurements are provided.
DO is the primary driver of nitrification vs. denitrification; the paper shows nitrate accumulation but does not report whether the system was aerobic or anaerobic.
Versuch. Operate at DO = 0, 2, 5, and 8 mg/L and measure NO3-N, NO2-N, and N2O production rates.
Hoch Measure and report current density (mA/m² or mA/cm²) and hydraulic retention time (HRT); only total current and power density are given.
Current density and HRT are critical operating parameters for nitrogen cycling kinetics; without them, the results cannot be reproduced or scaled.
Versuch. Report electrode area, calculate current density, and vary HRT from 6 to 48 hours while monitoring nitrogen species removal.
Hoch Quantify nitrite (NO2-N) and nitrous oxide (N2O) accumulation; only nitrate increase is reported.
Nitrite and N2O are toxic and potent greenhouse gases; the paper mentions qualitatively that nitrification occurred but provides no data on these intermediates.
Versuch. Measure NO2-N and N2O (by gas chromatography or ion chromatography) at each sampling point; report as mg/L or mg N/L.
Mittel Investigate the C/N ratio and its effect on nitrogen removal; no C/N ratio is reported or varied.
Swine wastewater typically has high C/N; the paper shows 85.92% COD removal and 55.90% ammonium-nitrogen removal, suggesting carbon was not limiting but the N removal pathway was incomplete.
Versuch. Vary influent C/N ratio from 5:1 to 20:1 and measure NO3-N, NO2-N, and N2O production.
Mittel Measure and control catholyte pH; no pH data are provided for the cathode or bulk solution.
pH affects nitrification kinetics and denitrification enzyme activity; the paper does not report pH control or monitoring.
Versuch. Operate at pH 6.5, 7.0, 7.5, and 8.0 and measure nitrification and denitrification rates.
Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen
Extrahierte Werte
Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.
n = 32 extrahierte Werte
Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.
6 von 30 extrahierten Zeilen modellierbar
- 2 nicht kanonisiert (kein kanonischer Slug)
- 1 kein SI-Wert
- 19 außerhalb physikalischer Grenzen
- 2 Physikprüfung nicht bestanden
| Parameter | Wert | Einheit | Konfidenz | Quelle | Anmerkungen | Modellierbar |
|---|---|---|---|---|---|---|
| Substrate | wastewater | — | 80 % | llm | ||
| Coulombic efficiency | 5,92 | % | 80 % | llm | ||
| Power Density | 100Außerhalb des physikalischen Bereichs, Quelle prüfen | mW/cm² | 100 % | extrahiert | "The maximum power density was 100 mW/cm2." · T=30°C, pH(an)=7, substrate=Glucose, HRT=24h, batch | Ausgeschlossen: außerhalb physikalischer Grenzen |
| Peak voltage v | 0,7 | V | 100 % | extrahiert | "The peak voltage was 0.7 V." · T=30°C, pH(an)=7, substrate=Glucose, HRT=24h, batch | Modellierbar |
| Open Circuit Voltage | 0,5 | V | 100 % | extrahiert | "The open circuit voltage was 0.5 V." · T=30°C, pH(an)=7, substrate=Glucose, HRT=24h, batch | Modellierbar |
| Anode material | were <jats:italic>corynebacterium </jats:italic>specie<jats:italic> | — | 70 % | extrahiert | Ausgeschlossen: kein SI-Wert | |
| Open circuit voltage | 0,516 | V | 60 % | extrahiert | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) | |
| Open Circuit Voltage×2 | 0,836 | V | 60 % | extrahiert | "g MFC Operation of Swine Wastewater" | Modellierbar |
| pH×2 | 58Außerhalb des physikalischen Bereichs, Quelle prüfen | - | 60 % | extrahiert | "on electricity generation in a" | Ausgeschlossen: außerhalb physikalischer Grenzen |
| pH×2 | 280Außerhalb des physikalischen Bereichs, Quelle prüfen | - | 60 % | extrahiert | "n (mg/l) 66 155 -134.85" | Ausgeschlossen: außerhalb physikalischer Grenzen |
| pH×2 | 895Außerhalb des physikalischen Bereichs, Quelle prüfen | - | 60 % | extrahiert | "n (mg/l) 66 155 -134.85" | Ausgeschlossen: außerhalb physikalischer Grenzen |
| pH×2 | 640Außerhalb des physikalischen Bereichs, Quelle prüfen | - | 60 % | extrahiert | "g/l) 66 155 -134.85" | Ausgeschlossen: außerhalb physikalischer Grenzen |
| pH×2 | 4.600Außerhalb des physikalischen Bereichs, Quelle prüfen | - | 60 % | extrahiert | "95.5 -273.60" | Ausgeschlossen: außerhalb physikalischer Grenzen |
| pH×2 | 95,5Außerhalb des physikalischen Bereichs, Quelle prüfen | - | 60 % | extrahiert | "95.5 -273.60" | Ausgeschlossen: außerhalb physikalischer Grenzen |
| pH×2 | 2.540Außerhalb des physikalischen Bereichs, Quelle prüfen | - | 60 % | extrahiert | "Mary and B. E. Logan. Removal of Odors from Swine Wastewater by" | Ausgeschlossen: außerhalb physikalischer Grenzen |
| pH×2 | 155Außerhalb des physikalischen Bereichs, Quelle prüfen | - | 60 % | extrahiert | "95.5 -273.60" | Ausgeschlossen: außerhalb physikalischer Grenzen |
| pH×2 | 688Außerhalb des physikalischen Bereichs, Quelle prüfen | - | 60 % | extrahiert | "95.5 -273.60" | Ausgeschlossen: außerhalb physikalischer Grenzen |
| pH×2 | 1 | - | 60 % | extrahiert | "Mary and B. E. Logan. Removal of Odors from Swine Wastewater by" | Ausgeschlossen: Physikprüfung nicht bestanden |
| Voltage×2 | 0,836 | V | 60 % | extrahiert | "on of Swine Wastewater" | Modellierbar |
| Microbial community | isolates identified at the biofilms on the anode were <jats:italic>corynebacterium </jats:italic>specie<jats:italic> | — | 50 % | extrahiert | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
Literatur-Priors
Im Vergleich zur Literatur
Der in der Publikation berichtete Wert (▼) ist auf der Literaturverteilung aus MESS-Parameters eingezeichnet. Werte außerhalb des Bands werden als Ausreißer gekennzeichnet.
Methodik
Welches System und wie es betrieben wurde
Methodik
Methodology
A single-chamber MFC was inoculated with swine wastewater and operated under unspecified conditions (no HRT, electrode potential, current density, or DO control reported). Open circuit voltage, current, power density, and physicochemical parameters (COD, BOD, ammonia, nitrate, phosphate) were monitored over an unspecified time period. Bacterial isolates were identified from anode biofilm by culture-based methods. No replicates, error bars, or statistical analysis are reported.
Systemkonfiguration
| Feld | Wert |
|---|---|
| reactor type | MFC |
| chamber config | 2-chamber |
Biologische Parameter
| Feld | Wert |
|---|---|
| microbial community | isolates identified at the biofilms on the anode were <jats:italic>corynebacterium </jats:italic>specie<jats:italic> |
Leistungskennzahlen
| Feld | Wert |
|---|---|
| coulombic efficiency | 5.92 |
| citation count | 5 |
Betriebsparameter
| Feld | Wert |
|---|---|
| substrate | ["wastewater"] |
Elektrochemische Daten
| Feld | Wert |
|---|---|
| open circuit voltage | 0.516 |
Betriebsbedingungen
1 Lauf extrahiert| Lauf | T°C | pHAnolyt | pHKatholyt | Substrat | [S]mg/L | HRTh | Modus | R_extΩ | V_appV | Inokulum |
|---|---|---|---|---|---|---|---|---|---|---|
| v2-994103b94cc61b7c | 30 | 7 | — | Glucose | 1000 | 24 | batch | — | — | — |
Ergebnisse
Was gemessen wurde und was funktioniert hat
Kernaussagen
Coulombic efficiency
Elektrochemie5.92Prozent
Extraktionspipeline
Rohextraktionen, Artefakte, Qualitätssignal
Extraktionsqualität
EhrlichkeitssignalBemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.
Parametervollständigkeit
63 %
Anteil der erwarteten Parameter, die extrahiert wurden
Datenvollständigkeit
70 %
Gesamtabdeckung der Extraktion über alle Felder
KI-Konfidenz
45 %
Vom Modell selbst angegebene Konfidenz
Mittlere Parameterkonfidenz
65 %
Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen
vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1
Diagramm-Explorer
Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.
Modell erkunden
Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.
KI-Erkenntnisse
Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.
Ähnliche Publikationen vergleichen
Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.
Quell-PDF
Die Publikation, wie sie erschienen ist.
Repräsentatives Modell, generisches MFC
Zum Interagieren tippenRepräsentatives Modell, generisches MFC
Repräsentatives Modell: MFC – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.
In diesem Datensatz
Organismen, Parameter und Materialien, die diese Publikation berichtet. Jeder Eintrag verweist auf seine Seite.
Organismen · 1
Parameter · 1
Schlagwörter
- Microbial fuel cell
- Chemical oxygen demand
- Wastewater
- Biochemical oxygen demand
- Nitrate
- Total dissolved solids
Zitieren
Emmanuel Egbadon, Campbell O. Akujobi, Chris O. Nweke et al. (2016). Simultaneous Generation of Bioelectricity and Treatment of Swine Wastewater in a Microbial Fuel Cell. International Letters of Natural Sciences. https://doi.org/10.56431/p-7y6x87
- Zeitschrift
- International Letters of Natural Sciences
Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.
Im Labor öffnen