Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.
Publikation · MFC
Efficiency of Photosynthetic Microbial Fuel Cells (pMFC) Depending on the Type of Microorganisms Inhabiting the Cathode Chamber
- MFC
- Dual Chamber
- Photosynthetic
- Biocathode
- Pure Culture
- Kathode: Biocathode
Zusammenfassung
Was die Publikation berichtet, in ihren eigenen Worten.
Zusammenfassung
Photosynthetic microbial fuel cells (pMFCs) are hybrid systems that enable simultaneous wastewater treatment under anaerobic conditions and the generation of electricity by utilizing the potential difference in the anaerobic anode chamber and the oxygenated cathode chamber. Dairy wastewater with a concentration of 2000 mg COD/L was treated in the anode of a batch pMFC. In the cathode chamber, Chlorella vulgaris or Arthrospira platensis was cultivated in synthetic medium, and next in diluted effluent from the anode chamber. The highest power density of 91 mW/m² was generated by the pMFC with the cultivation of Arthrospira platensis. Higher values of dissolved oxygen remained during the dark phase in the cathodic medium with Arthrospira platensis cultivation than with Chlorella vulgaris. This depletion of oxygen significantly decreased voltage generation, which during the light phase increased again to the maximum values. The COD removal achieved in the anodic chamber was 87%. The efficiency of nitrogen removal in the cathode chamber during the cultivation of Arthrospira platensis and Chlorella vulgaris was about 78% and 69%, respectively. The efficiency of phosphorus removal in the cathode chamber with the cultivation of Arthrospira plantensis and Chlorella vulgaris was 58% and 43%, respectively. This study has shown that the introduction of Arthrospira platensis into the cathode chamber is more effective than that of Chlorella vulgaris.
KI-Zusammenfassung
72 % KonfidenzThis study compared photosynthetic microbial fuel cells (pMFCs) using Arthrospira platensis or Chlorella vulgaris in the cathode to treat dairy wastewater (2000 mg COD/L, 278 mg TN/L) in the anode. Arthrospira platensis outperformed Chlorella vulgaris, generating 91 mW/m² versus lower power, with superior nitrogen removal (78% vs 69%) and more stable dissolved oxygen during dark phases (3.12 vs 1.1 mg O₂/L). Both microalgae were successfully cultivated on anode effluent after week 2, reducing medium costs. The control MFC with mechanical aeration produced only 57 mW/m², demonstrating the benefit of photosynthetic oxygen generation.
Zentrale Erkenntnisse
Zielkonflikt Arthrospira platensis maintained 3.12 mg O₂/L during dark phase versus 1.1 mg O₂/L for Chlorella vulgaris, resulting in voltage drop to 155 mV versus 90 mV, showing cyanobacteria's superior oxygen buffering capacity.
Was heißt das. If stable power output during dark periods is required, select Arthrospira platensis; if intermittent operation is acceptable, Chlorella vulgaris may suffice at lower cost.
Leistung Nitrogen removal efficiency was 78% with Arthrospira platensis versus 69% with Chlorella vulgaris, despite both species being cultivated on identical anode effluent (132 mg TN/L input).
Was heißt das. Arthrospira platensis is the preferred cathode organism for systems where nutrient recovery or N-removal is a co-objective alongside power generation.
Schwellenwert Power density increased 15–35% above mechanical aeration (57 mW/m²) when microalgae were added, reaching 90–91 mW/m², but this benefit depends on light availability and oxygen production rate.
Was heißt das. pMFCs are viable for light-exposed applications; in dark or low-light conditions, mechanical aeration may be more reliable unless oxygen buffering (Arthrospira) is prioritized.
Methode Anode effluent COD concentration (~221 mg/L after 87% removal) was sufficient to support mixotrophic microalgae growth when diluted and fed to the cathode every 2 weeks, reducing synthetic medium cost.
Was heißt das. Operators can reduce cathode medium cost by ~50% by recycling anode effluent; validate nutrient balance (N, P, trace metals) for your specific wastewater.
Mechanismus Voltage generation in pMFCs showed pronounced daily cycling (light: 300–500 mV, dark: 90–155 mV) due to photosynthetic oxygen production and respiration, whereas control MFC remained stable at ~200 mV.
Was heißt das. pMFC power output is unsuitable for constant-load applications without energy storage; design systems with buffering or accept variable output.
Ansatzpunkte6
Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.
Hoch No measurement of nitrogen speciation (NO₃⁻, NO₂⁻, NH₄⁺, N₂O) in cathode effluent; paper reports only total nitrogen removal % without identifying which N-species accumulated or were removed.
Abstract states 78% and 69% N-removal but Methods only measured TN and N-NH₄⁺; no mention of NO₃⁻, NO₂⁻, or N₂O. For denitrification systems, N₂O accumulation is a critical environmental concern.
Versuch. Measure NO₃⁻, NO₂⁻, NH₄⁺, and N₂O in cathode effluent at each 2-week cycle; quantify N-balance to identify if N is removed as gas, assimilated, or accumulated as nitrite.
Hoch No cathode potential or anode potential measurement; only voltage across 1 Ω external resistor reported. Electrode potentials relative to Ag/AgCl reference were recorded but not presented.
Methods state 'Reference electrodes comprising Ag/AgCl...were used to record electrode potentials' but no potentials appear in Results. Without cathode potential, cannot assess whether oxygen reduction is kinetically limited or whether nitrite/N₂O reduction is occurring.
Versuch. Report cathode and anode potential vs. SHE throughout light/dark cycles and across the 84-day operation; correlate with power density and N-species to identify electrochemical windows for nitrification vs. denitrification.
Mittel No investigation of current density or HRT effects on nitrogen removal; single HRT (weekly anode replacement) and single current density regime tested.
Paper does not vary HRT or current density. Don and Babel (cited) showed COD concentration in cathode affects power; no systematic study of how HRT or applied potential affects N-removal pathway or N₂O production.
Versuch. Test HRT 2–14 days and cathode potentials −0.2 to +0.4 V vs. SHE; measure N-species removal and N₂O emission to identify operating window for complete denitrification vs. nitrification.
Mittel Anode effluent COD concentration (~221 mg/L) is reported as a single value; no time-series or cycle-by-cycle tracking of COD in anode effluent or cathode medium.
Section 3.2 mentions 'COD concentration in the anode chamber was about 240 mg/L' but no table or figure shows COD evolution. Without COD profile, cannot assess whether heterotrophic vs. autotrophic conditions in cathode changed over 84 days.
Versuch. Track COD, TN, and TP in anode effluent and cathode medium at each 2-week replacement cycle; plot against chlorophyll-a and power density to identify nutrient-limiting phases.
Mittel No measurement of dissolved oxygen gradient between anode and cathode; paper notes oxygen can diffuse from cathode to anode but does not quantify this or measure anode DO.
Introduction cites Bazdar et al. on oxygen diffusion impairing anode performance, but no anode DO data presented. Cannot assess whether high cathode oxygen (18.65 mg/L with Arthrospira) compromised anode anaerobiosis.
Versuch. Measure DO in anode chamber during light and dark phases; if anode DO > 0.5 mg/L, test membrane or separator modifications to prevent oxygen cross-over.
Niedrig Chlorophyll-a used as proxy for biomass but no direct biomass (dry weight, AFDW) or protein yield reported; cannot assess true productivity or nutrient recovery per unit biomass.
Figure 4 shows chlorophyll-a only; no correlation to actual biomass or harvest yield. For cost-benefit analysis of using pMFC for nutrient recovery, biomass productivity is essential.
Versuch. Measure dry weight and protein content of harvested Arthrospira and Chlorella at each cycle; calculate N and P recovery per kg biomass and compare to synthetic medium cost.
Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen
Extrahierte Werte
Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.
n = 80 extrahierte Werte
Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.
45 von 77 extrahierten Zeilen modellierbar
- 15 nicht kanonisiert (kein kanonischer Slug)
- 13 kein SI-Wert
- 4 widerspricht anderen Publikationen
| Parameter | Wert | Einheit | Konfidenz | Quelle | Anmerkungen | Modellierbar |
|---|---|---|---|---|---|---|
| Chemical Oxygen Demand (COD) Concentration | 2.000 | mg/L | 95 % | llm | abstract | |
| Substrate | wastewater | — | 80 % | llm | ||
| Maximum power density | 91 | mW/m² | 80 % | llm | ||
| Electrode Surface Area×2 | 17,8 | cm² | 95 % | extrahiert | "The anode surface area was 28 cm2, and the cathode surface area was 17.84 cm2." · electrode_material=carbon rod | Modellierbar |
| Photoperiod×2 | 16 | h | 95 % | fluorescent lamps | "The cathode chamber was illuminated in a day–night cycle (16:8 h) with white lig…" · T=20°C, substrate=dairy wastewater | Modellierbar |
| Light Intensity×2 | 100 | mmol/photon/m² | 95 % | fluorescent lamps | "The cathode chamber was illuminated in a day–night cycle (16:8 h) with white lig…" · T=20°C, substrate=dairy wastewater | Ausgeschlossen: kein SI-Wert |
| Power Density×2 | 90 | mW/m² | 95 % | voltage and current measurement at 1 ω external resistor | "The maximum power density of about 90 mW/m2 was found in pMFC1." · T=20°C, substrate=dairy wastewater, steady_state | Modellierbar |
| Influent Total Phosphorus (TP)×2 | 35 | mg/L | 95 % | extrahiert | "The desired COD concentration was 2000 ± 156 mg COD/L, resulting in a nitrogen c…" · T=20°C, substrate=dairy wastewater | Modellierbar |
| Power Density×2 | 57 | mW/m² | 95 % | voltage and current measurement at 1 ω external resistor | "The highest power density obtained from the MFC with mechanical aeration was 57 …" · T=20°C, substrate=dairy wastewater, steady_state | Modellierbar |
| Initial Nitrogen Concentration×2 | 278 | mg/L | 95 % | extrahiert | "The desired COD concentration was 2000 ± 156 mg COD/L, resulting in a nitrogen c…" · T=20°C, substrate=dairy wastewater | Modellierbar |
| Air Flow Rate×2 | 120 | dm³/h | 95 % | extrahiert | "During start-up, the cathode chamber was filled with phosphate buffer and aerate…" · T=20°C, substrate=dairy wastewater | Modellierbar |
| Operating Temperature×2 | 30 | °C | 95 % | extrahiert | "The cyanobacteria were purchased as UTEX 3086 from the Culture Collection of Alg…" · T=30°C | Modellierbar |
| Power Density×3 | 91 | mW/m² | 95 % | voltage and current measurement at 1 ω external resistor | "The highest power density of 91 mW/m2 was generated by the pMFC with the cultiva…" · T=20°C, substrate=dairy wastewater, steady_state | Modellierbar |
| Dark Duration×2 | 8 | h | 95 % | fluorescent lamps | "The cathode chamber was illuminated in a day–night cycle (16:8 h) with white lig…" · T=20°C, substrate=dairy wastewater | Modellierbar |
| Membrane Dimensions×2 | 5 | cm | 95 % | extrahiert | "The anodic and cathodic chambers were separated by the membrane Nafion™117 (C7HF…" · condition_hint=Nafion 117 membrane | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Electrode Surface Area×2 | 28 | cm² | 95 % | extrahiert | "The anode surface area was 28 cm2, and the cathode surface area was 17.84 cm2." · electrode_material=carbon cloth | Modellierbar |
| Chemical Oxygen Demand (COD) Removal×4 | 87 | % | 95 % | extrahiert | "The COD removal achieved in the anodic chamber was 87%." · substrate=dairy wastewater, batch | Modellierbar |
| Chlorophyll-a Content×2 | 6,8 | mg/L | 90 % | algae analyzer | "The chlorophyll-a content after two weeks of MFC operation was 7.1 ± 0.6 mg/L an…" · T=20°C, substrate=dairy wastewater, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Dissolved Oxygen×2 | 1,1 | mg O₂/L | 90 % | dissolved oxygen meter | "The concentration of dissolved oxygen dropped to 1.1 mg O2/L (15.9% oxygen satur…" · T=20°C, substrate=dairy wastewater, steady_state | Ausgeschlossen: kein SI-Wert |
| Phosphorus Recovery×2 | 58 | % | 90 % | lck hach-lange cuvette tests and dr-5000 spectrophotometer | "The efficiency of phosphorus removal in the cathode chamber with the cultivation…" · T=20°C, substrate=dairy wastewater, steady_state | Modellierbar |
| Phosphorus Recovery×2 | 43 | % | 90 % | lck hach-lange cuvette tests and dr-5000 spectrophotometer | "The efficiency of phosphorus removal in the cathode chamber with the cultivation…" · T=20°C, substrate=dairy wastewater, steady_state | Modellierbar |
| Dissolved Oxygen×2 | 3,12 | mg O₂/L | 90 % | dissolved oxygen meter | "The concentration of dissolved oxygen dropped to 1.1 mg O2/L (15.9% oxygen satur…" · T=20°C, substrate=dairy wastewater, steady_state | Ausgeschlossen: kein SI-Wert |
| Dissolved Oxygen×2 | 11,4 | mg O₂/L | 90 % | dissolved oxygen meter | "during light conditions, dissolved oxygen reached 11.43 mg O2/L (142.9% oxygen s…" · T=20°C, substrate=dairy wastewater, steady_state | Ausgeschlossen: kein SI-Wert |
| Nitrogen Removal×2 | 69 | % | 90 % | lck hach-lange cuvette tests and dr-5000 spectrophotometer | "The efficiency of nitrogen removal in the cathode chamber during the cultivation…" · T=20°C, substrate=dairy wastewater, steady_state | Modellierbar |
| Dissolved Oxygen×2 | 18,7 | mg O₂/L | 90 % | dissolved oxygen meter | "and 18.65 mg O2/L (210.1% oxygen saturation) in the cathode medium with Arthrosp…" · T=20°C, substrate=dairy wastewater, steady_state | Ausgeschlossen: kein SI-Wert |
Methodik
Welches System und wie es betrieben wurde
Methodik
Methodology
Dual-chamber H-shaped MFCs (1 L each) with Nafion™117 membrane separator were operated in batch mode with weekly anode substrate replacement (dairy wastewater, 2000 mg COD/L, 278 mg TN/L). Cathode chambers were inoculated with either Arthrospira platensis (pMFC1) or Chlorella vulgaris (pMFC2) in synthetic media, then fed with diluted anode effluent every 2 weeks for 84 days. A control MFC (MFC0) with mechanical aeration (120 dm³/h) was run in parallel. Voltage and current were measured every 2 h across a 1 Ω external resistor; power density was normalized to anode area (28 cm²). COD, total nitrogen, ammonium, and total phosphorus were measured in influent, anode effluent, and cathode effluent using Hach-Lange cuvette tests. Dissolved oxygen was measured with a portable DO meter. Chlorophyll-a was used as a proxy for microalgae biomass. All experiments were performed in duplicate at ambient temperature (20–22 °C) with a 16:8 h light:dark cycle at 100 mmol/photon/m².
Systemkonfiguration
| Feld | Wert |
|---|---|
| reactor type | MES |
| chamber config | 2-chamber |
Leistungskennzahlen
| Feld | Wert |
|---|---|
| max power density | 91 |
| citation count | 5 |
Betriebsparameter
| Feld | Wert |
|---|---|
| substrate | ["wastewater"] |
Elektrochemische Daten
| Feld | Wert |
|---|---|
| max power density | 91 |
Betriebsbedingungen
15 Läufe extrahiert| Lauf | T°C | pHAnolyt | pHKatholyt | Substrat | [S]mg/L | HRTh | Modus | R_extΩ | V_appV | Inokulum |
|---|---|---|---|---|---|---|---|---|---|---|
| baseline_Arthrospira_platensis | — | — | — | dairy wastewater | 2000 | — | batch | — | — | — |
| baseline_Arthrospira_platensis #2 | — | — | — | dairy wastewater | 2000 | — | batch | — | — | — |
| baseline_Arthrospira_platensis #3 | — | — | — | dairy wastewater | 2000 | — | batch | — | — | — |
| baseline_Chlorella_vulgaris | — | — | — | dairy wastewater | 2000 | — | batch | — | — | — |
| baseline_Chlorella_vulgaris #2 | — | — | — | dairy wastewater | 2000 | — | batch | — | — | — |
| baseline_Chlorella_vulgaris #3 | — | — | — | dairy wastewater | 2000 | — | batch | — | — | — |
| cathode_effluent_Arthrospira_platensis | — | — | — | diluted effluent from anode chamber | — | — | batch | — | — | — |
| cathode_effluent_Arthrospira_platensis #2 | — | — | — | diluted effluent from anode chamber | — | — | batch | — | — | — |
| cathode_effluent_Chlorella_vulgaris | — | — | — | diluted effluent from anode chamber | — | — | batch | — | — | — |
| cathode_effluent_Chlorella_vulgaris #2 | — | — | — | diluted effluent from anode chamber | — | — | batch | — | — | — |
| v2-1d37291a400920a0 | 20 | — | — | dairy wastewater | 2000 | — | — | 1 | — | — |
| v2-2f1affd72d0147e9 | 30 | — | — | — | — | — | — | — | — | — |
| v2-b2310743b220d322 | — | — | — | dairy wastewater | 2000 | — | batch | — | — | — |
| v2-d3c1f07c2f67a392 | 20 | — | — | dairy wastewater | 2000 | — | steady_state | 1 | — | — |
| v2-f586e9af22985397 | — | — | — | — | — | — | — | — | — | — |
Extraktionspipeline
Rohextraktionen, Artefakte, Qualitätssignal
Extraktionsqualität
EhrlichkeitssignalBemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.
Parametervollständigkeit
50 %
Anteil der erwarteten Parameter, die extrahiert wurden
Datenvollständigkeit
70 %
Gesamtabdeckung der Extraktion über alle Felder
KI-Konfidenz
72 %
Vom Modell selbst angegebene Konfidenz
Mittlere Parameterkonfidenz
90 %
Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen
vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1
Diagramm-Explorer
Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.
Modell erkunden
Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.
KI-Erkenntnisse
Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.
Ähnliche Publikationen vergleichen
Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.
Quell-PDF
Die Publikation, wie sie erschienen ist.
Dieser Publikation ist noch kein 3D-Modell zugeordnet. Die daraus extrahierten Werte stehen unter „Extrahierte Werte“.
In diesem Datensatz
Organismen, Parameter und Materialien, die diese Publikation berichtet. Jeder Eintrag verweist auf seine Seite.
Organismen · 1
- Chlorella vulgaris or Arthrospira platensis
Materialien · 1
Schlagwörter
- Microorganism
- Microbial fuel cell
- Cathode
- Photosynthesis
- Botany
- Ecology
Zitieren
Marcin Zieliński, Paulina Rusanowska, Magda Dudek et al. (2024). Efficiency of Photosynthetic Microbial Fuel Cells (pMFC) Depending on the Type of Microorganisms Inhabiting the Cathode Chamber. Energies. https://doi.org/10.3390/en17102296
- Zeitschrift
- Energies