Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.
Publikation · MFC
Organic matter and ammonia removal by a novel integrated process of constructed wetland and microbial fuel cells
Zusammenfassung
Was die Publikation berichtet, in ihren eigenen Worten.
Zusammenfassung
A novel approach, combining a microbial fuel cell (MFC) with an integrated vertical flow constructed wetland (IVCW), was developed, and its ability to simultaneously produce electrical energy while treating swine wastewater was verified. The system combined the singular water flow path of a traditional vertical flow constructed wetland (upflow and downflow)-microbial fuel cell (CW-MFC), which demonstrates better characteristics in the aerobic, anoxic, and anaerobic regions. It not only enhanced the anti-pollution load ability and the organic compound removal effect, but also improved the gradient difference in the redox potential of the system. The results showed that the structure and substrate distribution in the device could both improve swine wastewater treatment and increase bioelectricity generation capabilities. The average chemical oxygen demand (COD) and ammonia nitrogen (NH 4 + -N) removal efficiencies were as high as 79.65% and 77.5%, respectively. Long-term and stable bioelectricity generation was achieved under continuous flow conditions. The peak values of the output voltage and power density were 713 mV and 456 mW m -3 . The activated carbon layer at the bottom of this system provided a larger surface for the growth of microbes. It showed significant promotion of the relative abundance of electrochemically active bacteria, which might result in the increase of bioelectricity generation in integrated vertical flow constructed wetland-microbial fuel cells (IVCW-MFCs). The electrochemically active bacteria, Geobacter and Desulfuromonas , were detected in the anodic biofilm by high-throughput sequencing analysis.
KI-Zusammenfassung
72 % KonfidenzThis paper describes an integrated vertical-flow constructed wetland–microbial fuel cell (IVCW-MFC) treating swine wastewater with dual downflow–upflow zones. The closed-circuit system achieved 79.65% COD removal (102.7 mg/L effluent from 505 mg/L inlet) and 77.5% NH₄⁺–N removal (average inlet 215 mg/L) over 92 days at 2-day HRT, while generating 713 mV peak voltage and 456 mW/m³ power density. The anode region (10.4% of liquid volume) removed 58.93% of total COD and 71.4% of total NH₄⁺–N, with nitrification producing NO₃⁻–N that was subsequently denitrified to 75.13% removal. Closed-circuit operation improved COD removal by 14.94% over open-circuit, attributed to the anode acting as a temporary electron acceptor.
Zentrale Erkenntnisse
Mechanismus Anode region (10.4% of liquid volume) removed 58.93% of total COD and 71.4% of total NH₄⁺–N removal, with COD removal ratio 26.9% higher than equivalent activated carbon layer alone
Was heißt das. Concentrate anode design and biofilm support in the upper anode zone to maximize organic oxidation and ammonia removal before water reaches the cathode
Mechanismus Nitrification in the downflow anode region produced NO₃⁻–N accounting for 49.02% (closed-circuit) and 46.12% (open-circuit) of NH₄⁺–N removal, followed by denitrification to 75.13% (closed) vs 66.47% (open)
Was heißt das. Design the downflow zone for nitrification with oxygen from plant roots, then rely on anoxic zones and denitrifying bacteria in the cathode region to complete nitrogen removal; closed-circuit operation enhances denitrification by 8.66 percentage points
Zielkonflikt Closed-circuit operation improved COD removal by 14.94 percentage points (79.65% vs 64.71%) and NH₄⁺–N removal by 57.6% relative improvement, attributed to anode acting as temporary electron acceptor
Was heißt das. Operating in closed-circuit mode with external load is essential for maximizing both organic and nitrogen removal; the bioelectrochemical pathway enhances anaerobic biodegradation
Schwellenwert Internal resistance of 463.66 Ω was theoretically close to external resistance of 450 Ω, enabling high power density of 456 mW/m³ at 22.5 mA/m² current density
Was heißt das. Match external load resistance to internal resistance to maximize power output; the continuous water flow and high electrode conductivity minimize ohmic losses
Leistung Voltage stabilized in two phases: first stable phase at ~6 days, second stable phase at ~18 days total, with stable operation range 598–713 mV during the 92-day study
Was heißt das. Allow 18 days startup time for biofilm maturation and microbial community establishment before relying on stable power output; expect voltage fluctuations of ±57.5 mV during steady operation
Ansatzpunkte6
Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.
Hoch No measurement of N₂O or NO accumulation during denitrification despite high NO₃⁻–N reduction (75.13%)
The paper reports substantial denitrification but does not quantify whether N₂O is produced as an intermediate or final product. Section 3.2 states 'The NO₃⁻–N decreased from its highest concentration at 70.62 mg/L...to its lowest concentration at 17.56 mg/L' but does not account for the nitrogen mass balance or specify the end product (N₂ vs N₂O)
Versuch. Measure N₂O and NO in gas phase above cathode and in effluent using gas chromatography or FTIR; vary cathode potential and dissolved oxygen to determine operating window that maximizes N₂ production and minimizes N₂O
Hoch No systematic variation of cathode potential or dissolved oxygen concentration to optimize denitrification selectivity
The paper operates with a fixed external resistance (1000 Ω) and relies on passive aeration via plant roots and air cathode. Section 3.2 mentions 'aerobic denitriers...could use both oxygen and nitrate as terminal electron acceptors' but does not test how cathode potential or DO affects the balance between aerobic and anaerobic denitrification pathways
Versuch. Vary external resistance (100–10,000 Ω) or apply controlled cathode potential (−0.2 to +0.2 V vs Ag/AgCl) while measuring NO₃⁻–N, NO₂⁻–N, N₂O, and N₂ production; determine the potential window that maximizes complete denitrification to N₂
Mittel No measurement of nitrite (NO₂⁻–N) accumulation or transient dynamics during nitrification–denitrification coupling
The paper measures only NH₄⁺–N and NO₃⁻–N, not NO₂⁻–N. Section 3.2 describes nitrification producing NO₃⁻–N but does not report whether NO₂⁻–N accumulates as an intermediate, which could indicate incomplete nitrification or inhibition of nitrite oxidizers
Versuch. Add NO₂⁻–N to the sampling protocol at all ports (influent, S1–S8, effluent); measure daily during steady state to detect transient accumulation under varying inlet loads
Mittel No variation of hydraulic retention time (HRT) or organic loading rate to determine the operating window for simultaneous nitrification–denitrification
The system operates at a fixed HRT of 2 days and inlet COD of 324–708 mg/L. Section 3.1 states 'The MFCs and IVCW-MFCs operate more efficiently under a lower organic matter load' but does not test the trade-off between COD removal, nitrogen removal, and power generation across a range of HRTs (0.5–5 days) or C/N ratios
Versuch. Operate parallel reactors at HRT 0.5, 1, 2, 3, 5 days with constant inlet COD or varying C/N ratio (5:1 to 20:1 by mass); measure COD, NH₄⁺–N, NO₃⁻–N, NO₂⁻–N, N₂O, and power density to identify the optimal HRT for nitrogen removal without sacrificing power output
Mittel No measurement of catholyte pH or anode pH dynamics, despite mention of pH gradient effects on power generation
Section 3.3 states 'a continuous influx was used in this experiment; the wastewater flowed from anode to cathode while transporting protons, shortening the pH gradient between the two points and avoiding the small effect of electricity production caused by excess acidity at the anode or excess alkalinity at the cathode' but no pH data are provided
Versuch. Install pH probes at anode inlet, anode outlet, cathode inlet, and cathode outlet; measure pH daily during steady state and correlate with voltage output and nitrogen species concentrations to quantify the pH gradient effect on power generation and nitrification–denitrification balance
Mittel No characterization of the microbial community in the cathode region or comparison of anode vs cathode communities under closed-circuit vs open-circuit operation
Section 2.3 states 'the substrate-attached biolms from these two regions were sampled for microbial community analysis' and Section 3.3 mentions Geobacter and Desulfuromonas in the anode, but the results section does not present cathode community data or compare the two circuits
Versuch. Perform 16S rRNA sequencing on anode and cathode biofilms from both closed-circuit and open-circuit reactors; quantify the relative abundance of nitrifiers (Nitrosomonas, Nitrobacter), denitrifiers (Paracoccus, Pseudomonas), and electrochemically active bacteria (Geobacter, Desulfuromonas) to identify which taxa drive the 14.94% COD and 57.6% NH₄⁺–N improvement in closed-circuit mode
Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen
Extrahierte Werte
Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.
n = 65 extrahierte Werte
Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.
35 von 65 extrahierten Zeilen modellierbar
- 27 nicht kanonisiert (kein kanonischer Slug)
- 2 kein SI-Wert
- 1 widerspricht anderen Publikationen
| Parameter | Wert | Einheit | Konfidenz | Quelle | Anmerkungen | Modellierbar |
|---|---|---|---|---|---|---|
| Chemical Oxygen Demand (COD) Removal | 64,7 | % | 95 % | potassium dichromate method | "After stable treatment with a two-day HRT, the average effluent concentration of…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Modellierbar |
| Electrode Surface Area | 10 | cm | 95 % | extrahiert | "the anode adopted a stainless-steel wire mesh to wrap the activated carbon parti…" · T=33°C | Ausgeschlossen: kein SI-Wert |
| Chemical Oxygen Demand (COD) Concentration | 103 | mg/L | 95 % | potassium dichromate method | "After stable treatment with a two-day HRT, the average effluent concentration of…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Modellierbar |
| Chemical Oxygen Demand (COD) Concentration | 708 | mg/L | 95 % | potassium dichromate method | "the influent COD concentrations varied from 324–708 mg L1" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Modellierbar |
| Chemical Oxygen Demand (COD) Concentration | 505 | mg/L | 95 % | potassium dichromate method | "the influent COD concentrations varied from 324–708 mg L1, and the average conce…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Modellierbar |
| Electrode Surface Area | 20 | cm | 95 % | extrahiert | "Carbon felt was used as the cathode (20 cm × 20 cm)" · T=33°C | Ausgeschlossen: kein SI-Wert |
| Temperature | 33 ± 5 (range) | °C | 95 % | extrahiert | "the average temperature during the entire period of operation, which occurred in…" · T=33°C | Modellierbar |
| Chemical Oxygen Demand (COD) Removal | 79,7 | % | 95 % | potassium dichromate method | "The average chemical oxygen demand (COD) and ammonia nitrogen (NH4+–N) removal e…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Modellierbar |
| Ammonia nitrogen (NH4+–N) removal efficiency | 77,5 | % | 95 % | sodium reagent method | "The average chemical oxygen demand (COD) and ammonia nitrogen (NH4+–N) removal e…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Influent NH4+–N concentration (average) | 215 | mg/L | 95 % | sodium reagent method | "the inflow NH4+–N concentrations varied from 138–284 mg L1, with an average conc…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Influent NH4+–N concentration (range low) | 138 | mg/L | 95 % | sodium reagent method | "the inflow NH4+–N concentrations varied from 138–284 mg L1" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Influent NH4+–N concentration (range high) | 284 | mg/L | 95 % | sodium reagent method | "the inflow NH4+–N concentrations varied from 138–284 mg L1" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| NH4+–N removal efficiency (closed-circuit) | 77,5 | % | 95 % | sodium reagent method | "The average removal rate of IVCW-MFC-C reached 77.5%, which was higher than that…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Output voltage range (stable operation) | 598 | mV | 95 % | data logger (ads1115 and ch341a logger) | "In the stable operation period, the output voltage of the system was in the rang…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Output voltage range (stable operation) | 713 | mV | 95 % | data logger (ads1115 and ch341a logger) | "In the stable operation period, the output voltage of the system was in the rang…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Reactor cross-section dimensions | 40 | cm | 95 % | extrahiert | "with a square cross-section of 40 × 20 cm" · T=33°C | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Daily wastewater flow rate | 5,75 | L/d | 95 % | extrahiert | "each CW-MFC treated 5.75 L of swine wastewater daily with an HRT of two days" · T=33°C, substrate=swine wastewater, HRT=48h | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Chemical Oxygen Demand (COD) Concentration | 181 | mg/L | 95 % | potassium dichromate method | "After stable treatment with a two-day HRT, the average effluent concentration of…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Modellierbar |
| Reactor Volume Total | 37,8 | L | 95 % | extrahiert | "The volume of the whole container was 37.8 L, with an effective volume of 11.5 L…" · T=33°C | Modellierbar |
| Voltage | 713 | mV | 95 % | data logger (ads1115 and ch341a logger) | "The peak values of the output voltage and power density were 713 mV and 456 mW m…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Modellierbar |
| Reactor Volume | 11,5 | L | 95 % | extrahiert | "The volume of the whole container was 37.8 L, with an effective volume of 11.5 L…" · T=33°C | Modellierbar |
| Reactor Height | 50 | cm | 95 % | extrahiert | "the IVCW-MFC reactor was made of a 50 cm tall polyacrylic plastic box" · T=33°C | Modellierbar |
| Chemical Oxygen Demand (COD) Concentration | 324 | mg/L | 95 % | potassium dichromate method | "the influent COD concentrations varied from 324–708 mg L1" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Modellierbar |
| Cell Doubling Time | 92 | d | 95 % | extrahiert | "The swine wastewater was provided for 92 consecutive days." · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Modellierbar |
| NO3–N concentration (highest, open-circuit) | 70,3 | mg/L | 90 % | phenol-2-sulfonic acid method | "The NO3–N decreased from its highest concentration at 70.62 mg L1 (IVCW-MFC-C) a…" · T=33°C, substrate=swine wastewater, HRT=48h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
Methodik
Welches System und wie es betrieben wurde
Methodik
Methodology
The IVCW-MFC reactor (50 cm tall, 40×20 cm cross-section, 11.5 L effective volume) was divided into downflow and upflow zones by a partition with a 5 cm unblocked gap at the bottom. The anode (stainless-steel mesh wrapping activated carbon, 20×20×10 cm) was buried in the downflow zone (30–40 cm depth); the cathode (carbon felt, 20×20 cm) was placed on the upflow surface. Activated carbon layers (5 cm height) were installed in both zones. The system was inoculated with anaerobic digestion sludge and operated for ~1 month before testing. Real swine wastewater (post-biogas treatment) was fed continuously at 5.75 L/day (HRT 2 days) for 92 days. Closed-circuit (IVCW-MFC-C) and open-circuit (IVCW-MFC-O) modes were operated in parallel (n=3 each). Samples were collected every 2 days from 8 ports (S1–S8) plus influent and effluent, analyzed for COD (dichromate method), NO₃⁻–N and NH₄⁺–N (phenol-sulfonic acid and sodium reagent methods). Voltage was logged every 6 minutes; polarization curves were measured at end-of-study to determine power density and internal resistance. Microbial communities were characterized by 16S rRNA sequencing (Illumina MiSeq, V3–V4 region) of anode and cathode biofilms.
Systemkonfiguration
| Feld | Wert |
|---|---|
| reactor type | MES |
| chamber config | 2-chamber |
Betriebsbedingungen
10 Läufe extrahiert| Lauf | T°C | pHAnolyt | pHKatholyt | Substrat | [S]mg/L | HRTh | Modus | R_extΩ | V_appV | Inokulum |
|---|---|---|---|---|---|---|---|---|---|---|
| v2-19eaff737f7d700a | 33 | — | — | swine wastewater | 505 | 48 | — | — | — | — |
| v2-1f6602261d63acaa | 28 | — | — | glucose with ammonium chloride | 700 | — | startup | — | — | — |
| v2-2fcf07ec09893244 | 33 | — | — | swine wastewater | 505 | 48 | steady_state | — | — | — |
| v2-36823d77049999a9 | 33 | — | — | swine wastewater | 505 | 48 | startup | 1000 | — | — |
| v2-679b5d3d48f421f1 | 33 | — | — | swine wastewater | 708 | 48 | steady_state | — | — | — |
| v2-7c3a638b1d1fb0fa | 33 | — | — | swine wastewater | 215 | 48 | steady_state | 1000 | — | — |
| v2-9f2a5e3fe4309ae0 | 33 | — | — | — | — | — | — | — | — | — |
| v2-aa712c306b8d8488 | 33 | — | — | swine wastewater | 505 | 48 | steady_state | 1000 | — | — |
| v2-ce46d75f66240754 | 33 | — | — | swine wastewater | 324 | 48 | steady_state | — | — | — |
| v2-d3c9394182297582 | 28 | — | — | glucose | 700 | — | startup | — | — | — |
Extraktionspipeline
Rohextraktionen, Artefakte, Qualitätssignal
Extraktionsqualität
EhrlichkeitssignalBemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.
KI-Konfidenz
72 %
Vom Modell selbst angegebene Konfidenz
Mittlere Parameterkonfidenz
90 %
Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen
vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1
Diagramm-Explorer
Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.
Modell erkunden
Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.
KI-Erkenntnisse
Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.
Ähnliche Publikationen vergleichen
Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.
Quell-PDF
Die Publikation, wie sie erschienen ist.
Repräsentatives Modell, generisches MFC
Zum Interagieren tippenRepräsentatives Modell, generisches MFC
Repräsentatives Modell: MFC – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.
Schlagwörter
- Ammonia
- Wetland
- Microbial fuel cell
- Organic matter
- Process (computing)
- Constructed wetland
Zitieren
Feng Liu, Lei Sun, Jinbao Wan et al. (2019). Organic matter and ammonia removal by a novel integrated process of constructed wetland and microbial fuel cells. RSC Advances. https://doi.org/10.1039/c8ra10625h
- PubMed
- 35515927
- Zeitschrift
- RSC Advances
Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.
Im Labor öffnen