Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation · MFC

Simultaneous Electricity Generation and Heavy Metals Reduction from Distillery Effluent by Microbial Fuel Cell

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

Interaktives 3D-Modell

Zusammenfassung

Objectives: Raw distillery effluent put to use as substrate for electricity generation in MFC and effectiveness in treatment including heavy metals reduction using MFC are the focus of the study. Methods/Statistical Analysis: Dual chamber fuel cells were fabricated using Poly (methyl methacrylate) sheet as a single unit, graphite rods are used as electrodes. Microporous PVC separators are used for salt bridge to distinct the anode and cathode chambers so as comparing with the conventional ‘H’ type dual chamber reactor the distance between the electrodes are reduced. The fuel cells were operated in batch mode at room temperature. Findings: The Microbial Fuel Cell is a bio-electrochemical device draws electricity from the microorganism that utilizes the organic matter from the wastewater, different wastewater could be employed as a substrate. Distillery effluent consist of high chemical oxygen demand, it effectuated electricity generation for 73 days. The fuel cells produced a maximum voltage of 206 mV that derived a maximum current density 123.50 mA/m² and power density of 25194.8 mW/m² . Electricity generation and effluent treatment depends on the ability of the microorganism to convert the organic matter of the substrate. The COD removal 68.7% was obtained from the fuel cell it is effective than the conventional treatment techniques without pretreatment or dilution of the effluent. The MFC treatment also assisted the removal of Nitrate 76.6%, Phosphate 79.4%, Sulphate 70.8%. The overall performance of the fuel cell determined by the Columbic Efficiency rendered by the process was 47.12%. Elemental analysis of treated effluent exhibited considerable reduction of heavy metals present in the distillery effluent. Application/Improvements: This study shows that the treatment of raw distillery effluent is effective with MFC technique. It also signifies the potential of heavy metal reduction with MFC by simultaneous electricity generation. Keywords: COD, Distillery Effluent, Electricity, Heavy metals, MFC, Treatment

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

Noch nicht extrahiert

Diese Publikation steht in der Warteschlange der MESSAI-Extraktionspipeline. Versuchsbedingungen, Leistungskennzahlen und strukturierte Parameter erscheinen hier, sobald sie verarbeitet ist – schauen Sie später wieder vorbei oder öffnen Sie oben das Original-PDF, um sie jetzt zu lesen.

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

3D-Modell wird geladen …

Repräsentatives Modell, generisches MFC

Repräsentatives Modell: MFC – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.

MFC
System
0
Extrahierte Werte
2017
Jahr

Schlagwörter

  • Microbial fuel cell
  • Effluent
  • Pulp and paper industry
  • Anode
  • Chemical oxygen demand
  • Electricity generation

Zitieren

Hanish Mohammed Coppath Hamza, Prabha Duraisamy, Selvendiran Periyasamy et al. (2017). Simultaneous Electricity Generation and Heavy Metals Reduction from Distillery Effluent by Microbial Fuel Cell. Indian Journal of Science and Technology. https://doi.org/10.17485/ijst/2017/v10i13/111203

Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.

Im Labor öffnen