Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation · MFC

Enhancing the Electricity Generation and Nitrate Removal of Microbial Fuel Cells With a Novel Denitrifying Exoelectrogenic Strain EB-1

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

Interaktives 3D-ModellKI-angereichert· 78 %

KI-Zusammenfassung

78 % Konfidenz

This paper isolates and characterizes Mycobacterium sp. EB-1, a novel denitrifying exoelectrogen capable of simultaneous anodic denitrification and electricity generation in a two-chamber MFC. The strain achieves 0.84 W/m² power density and removes NO₃⁻-N at 0.66 kg N/m³/d with no inhibition of voltage output despite increasing nitrate (0–200 mg/L NO₃⁻-N). Electron flux analysis reveals that denitrification and anode respiration compete for electrons from acetate, with coulombic efficiency dropping from 83.9% to 6.5% as nitrate rises, indicating electron donor limitation rather than system inhibition.

Zentrale Erkenntnisse

  • Schwellenwert Voltage output (Vmax) remained stable across NO₃⁻-N concentrations 0–200 mg/L, while cycle duration shortened, proving concurrent denitrification and anode respiration are electron-donor limited, not inhibited.

    Was heißt das. Operators can tolerate high nitrate loads without voltage collapse if acetate supply is adequate; design for electron donor availability, not nitrate toxicity.

  • Zielkonflikt Coulombic efficiency (CE) dropped from 83.9 ± 2.7% (no nitrate) to 6.5 ± 2.2% (200 mg/L NO₃⁻-N), while corrected CE (excluding denitrification electrons) remained ~90%, showing denitrification diverts 77% of electrons at high nitrate.

    Was heißt das. If power recovery is the goal, minimize nitrate or operate at low NO₃⁻-N (<50 mg/L); if nitrogen removal is primary, accept low CE and design for electron flux partitioning.

  • Leistung Nitrite accumulation remained <1 mg/L throughout all tests despite NO₃⁻-N reduction to N₂, indicating complete denitrification pathway without intermediate accumulation.

    Was heißt das. No need for post-treatment to remove nitrite or ammonia; design can assume complete N₂ production without intermediate trapping.

  • Mechanismus Direct electron transfer (DET) mechanism confirmed by rapid CV recovery (41.2% recovery in 5 min, 92.1% in 10 min after medium replacement) and two redox peaks at −0.21 V and −0.185 V (vs. Ag/AgCl), consistent with outer membrane c-type cytochromes.

    Was heißt das. Gram-positive Mycobacterium can use DET like gram-negative model organisms; electrode material selection should optimize for c-type cytochrome interaction, not rely on soluble mediators.

  • Leistung Nitrate removal rate of 0.66 ± 0.01 kg N/m³/d (27.7 ± 0.5 mg N/L/h) at 200 mg/L NO₃⁻-N exceeds biocathode MFC rates (0.02–0.43 kg N/m³/d) and matches conventional heterotrophic denitrification (0.08–1.36 kg N/m³/d with carbon).

    Was heißt das. Anodic denitrification with EB-1 is kinetically competitive with conventional treatment; consider for high-nitrate, low-COD/N wastewater where biocathodes underperform.

Widersprüche1

Nur Konflikte, die die Publikation selbst zeigt, jeweils am Text geprüft.

  • Gegenüber früherer Arbeit Prior work showed nitrate inhibits current generation in denitrifying exoelectrogens, but this strain shows no voltage inhibition.

    Eine Seite

    Comamonas denitrificans DX-4 and Calditerrivibrio nitroreducens produced decreased voltage when nitrate was added (Xing et al. 2010, Fu et al. 2013)

    “The power output of MFCs with Comamonas denitrificans (Xing et al., 2010) or Calditerrivibrio nitroreducens (Fu et al., 2013) was found to be decreased when nitrate was added to the anode chamber of MFCs”
    Andere Seite

    Mycobacterium sp. EB-1 showed 'maximum voltage output (Vmax) was rarely affected' by NO₃⁻-N up to 200 mg/L

    “the maximum voltage output (Vmax) was rarely affected. The concurrent processes of denitrification and anode respiration are thus a limitation of the electron donor rather than an inhibition of the system.”

    Einordnung der Autoren. Authors attribute the difference to electron donor limitation vs. inhibition: in prior work, external resistance was lower (100 Ω vs. 1 kΩ here), limiting electron transfer rate and forcing competition; in EB-1, the 1 kΩ resistance allows sufficient electron flux for both pathways without voltage collapse. The domestication process may also have selected for EB-1 strains with higher denitrification enzyme expression.

Ansatzpunkte6

Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.

  • Hoch No systematic variation of external resistance (only 1 kΩ tested); prior work (Xing et al. 2010, Fu et al. 2013) used 100 Ω and showed inhibition. Test 100–10,000 Ω to map the operating window where voltage remains stable vs. collapses with increasing NO₃⁻-N.

    Authors note that external resistance affects electron transfer rate and competition between pathways, but only one resistance value is used. Figure 6A shows cycle duration shortens with NO₃⁻-N; lower resistance might reveal voltage collapse.

    Versuch. External resistance: 100, 500, 1000, 5000 Ω; NO₃⁻-N: 0, 50, 100, 200 mg/L; measure Vmax, cycle time, CE, and electron flux partitioning.

  • Hoch No exploration of COD/N ratio trade-off; acetate held constant at 780.5 mg/L COD while NO₃⁻-N varied 0–200 mg/L, giving COD/N ratios of ∞ to 3.9. Critical COD/N for complete denitrification is mentioned (equation 3) but not experimentally validated.

    Text states 'low COD/N ratios significantly inhibit current generation' and cites prior work showing no current at low COD/N, but this paper does not test the boundary. Figure 6 shows 82.8% removal at 200 mg/L NO₃⁻-N (COD/N ≈ 3.9), but incomplete removal; the critical threshold is not identified.

    Versuch. COD/N ratio: 2, 3, 4, 5, 7 (acetate fixed, NO₃⁻-N varied); measure voltage, CE, nitrate removal %, and electron flux to identify minimum COD/N for complete denitrification without voltage loss.

  • Mittel Catholyte pH and dissolved oxygen not controlled or reported; only anode chamber conditions detailed. Cathode performance and O₂ reduction kinetics may limit overall MFC performance at high current densities.

    Methods state '100 mM sterilized PBS was used as the catholyte' but no pH monitoring or control is mentioned. Figure 3B shows power density curve but not cathode potential or O₂ limitation effects. At 1.9 A/m² current, cathode may become rate-limiting.

    Versuch. Measure cathode potential, dissolved O₂ in catholyte, and pH during operation at 0–200 mg/L NO₃⁻-N; vary catholyte pH (6.5–8.5) and O₂ saturation to assess cathode contribution to voltage loss.

  • Mittel Hydraulic retention time (HRT) not varied; all experiments are batch mode with medium replacement when voltage drops below 20 mV. No continuous-flow or fed-batch operation tested to assess practical treatment rates and stability.

    Batch operation with manual replacement is not scalable. Text reports 'average nitrate removal rate of 0.66 kg N/m³/d' but this is calculated from batch data; actual HRT and volumetric throughput are not specified. Cycle duration shortens with NO₃⁻-N (Figure 6A) but implications for continuous operation are unclear.

    Versuch. Continuous-flow operation at HRT 12, 24, 48 h; NO₃⁻-N 50, 100, 200 mg/L; measure steady-state voltage, CE, nitrate removal %, and N₂O production.

  • Mittel N₂O production not measured; only N₂ and NH₄⁺ quantified. Incomplete denitrification to N₂O is a known issue in bioelectrochemical systems and could represent a significant electron loss and environmental concern.

    Text states 'nitrate was reduced to nitrogen gas and no ammonium was detected' but N₂O is not mentioned in the analytical methods (Section 'Calculation'). At 200 mg/L NO₃⁻-N, 82.8% removal in 6 h leaves 17.2% unaccounted; N₂O could be a product.

    Versuch. Gas chromatography or membrane inlet mass spectrometry to quantify N₂, N₂O, and NO in headspace at NO₃⁻-N 50, 100, 200 mg/L; correlate N₂O yield with cathode potential and dissolved O₂.

  • Mittel Anode potential not controlled or reported; only external resistance (1 kΩ) and voltage output measured. Anode potential is critical for denitrification enzyme activity and electron transfer kinetics but is not characterized.

    Methods describe polarization curves (Figure 3B) but do not report anode potential vs. SHE or Ag/AgCl. CV analysis (Figure 4) uses Ag/AgCl reference but anode potential during batch operation is not provided. This limits reproducibility and mechanistic understanding.

    Versuch. Potentiostat-controlled anode potential: −0.3, −0.2, −0.1, 0 V vs. Ag/AgCl; NO₃⁻-N 0, 100, 200 mg/L; measure current, CE, denitrification rate, and electron flux partitioning.

Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

n = 16 extrahierte Werte

Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.

9 von 16 extrahierten Zeilen modellierbar

  • 6 nicht kanonisiert (kein kanonischer Slug)
  • 1 kein SI-Wert
ParameterWertEinheitKonfidenzQuelleAnmerkungenModellierbar
Current Density1,9A m⁻²90 %
extrahiert
"A maximum power density (MPD) of 0.84 ± 0.05 W m−2 was obtained at a current den…" · T=30°C, pH(an)=7, substrate=sodium acetateModellierbar
Coulombic efficiency6,5%90 %
extrahiert
"An apparent reduction of CE (from 83.9 ± 2.7% to 6.5 ± 2.2%) was observed with i…" · T=30°C, pH(an)=7, substrate=sodium acetateModellierbar
Voltage450mV90 %
extrahiert
"the voltage was rapidly increased to 450.4 mV in the third cycle" · T=30°C, pH(an)=7, substrate=sodium acetateModellierbar
Corrected Coulombic Efficiency43,3%90 %
extrahiert
"The CCE sharply decreased to 43.3 ± 5.0 % at the NO−3 -N concentration of 200 mg…" · T=30°C, pH(an)=7, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Power Density0,84W m⁻²90 %
extrahiert
"A maximum power density (MPD) of 0.84 ± 0.05 W m−2 was obtained at a current den…" · T=30°C, pH(an)=7, substrate=sodium acetateModellierbar
Corrected Coulombic Efficiency92,4%90 %
extrahiert
"the CCEs increased and then decreased, and a maximum value of 92.4 ± 3.0 % was o…" · T=30°C, pH(an)=7, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Nitrate Removal100%90 %
extrahiert
"Additionally, almost all of NO−3 -N was removed by strain EB-1, indicating that …" · T=30°C, pH(an)=7, substrate=glucoseModellierbar
Net COD/N Ratio3,23—90 %
extrahiert
"For the denitrifying exoelectrogen EB-1, the net COD/N ratios for denitrificatio…" · T=30°C, pH(an)=7, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Net COD/N Ratio9,36—90 %
extrahiert
"For the denitrifying exoelectrogen EB-1, the net COD/N ratios for denitrificatio…" · T=30°C, pH(an)=7, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Nitrate Removal82,8%90 %
extrahiert
"Further, 82.8 ± 6.5 % NO−3 -N was removed within the first 6 h when 200 mg L−1 N…" · T=30°C, pH(an)=7, substrate=sodium acetateModellierbar
Nitrate Removal100%90 %
extrahiert
"As shown in Figure 6B, almost all of nitrate was removed when the NO−3 -N concen…" · T=30°C, pH(an)=7, substrate=sodium acetateModellierbar
Net COD/N Ratio3,75—90 %
extrahiert
"For the denitrifying exoelectrogen EB-1, the net COD/N ratios for denitrificatio…" · T=30°C, pH(an)=7, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Nitrate Removal×2100%90 %
extrahiert
"Additionally, almost all of NO−3 -N was removed by strain EB-1" · T=30°C, pH(an)=7, substrate=starchModellierbar
Net COD/N Ratio3,18—90 %
extrahiert
"For the denitrifying exoelectrogen EB-1, the net COD/N ratios for denitrificatio…" · T=30°C, pH(an)=7, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Nitrate Removal0,66kg N m⁻³ d⁻¹90 %
extrahiert
"An average nitrate removal rate of 0.66 ± 0.01 kg N m−3 d−1 (27.7 ± 0.5 mg N L−1…" · T=30°C, pH(an)=7, substrate=sodium acetateAusgeschlossen: kein SI-Wert

Methodik

Welches System und wie es betrieben wurde

Methodik

Methodology

Two-chamber MFC with 15 mL anode and cathode separated by cation exchange membrane. Anode: carbon fiber felt (2 cm³); cathode: Pt-coated carbon cloth (7 cm²). Strain EB-1 isolated from enriched anodic biofilm via dilution plating and identified by 16S rDNA sequencing. Batch operation with 1 kΩ external resistance; voltage recorded every 5 min. Electrochemical analysis via polarization curves and cyclic voltammetry (CV) at 1 mV/s scan rate. Nitrogen species (NO₃⁻-N, NO₂⁻-N, NH₄⁺-N) quantified by UV spectrophotometry. Electron flux partitioned into anode respiration (from current), denitrification (from NO₃⁻-N loss), and other losses (biomass, overpotential).

Systemkonfiguration

FeldWert
reactor typeMFC
chamber config2-chamber

Leistungskennzahlen

FeldWert
citation count50

Betriebsbedingungen

4 Läufe extrahiert
LaufT°CpHAnolytpHKatholytSubstrat[S]mg/LHRThModusR_extΩV_appVInokulum
v2-4c82d21436f581d9307—glucose———1000——
v2-b05e904cce0c0f1a307—sodium acetate———1000——
v2-be15bbad0b0a63d4307—starch———1000——
v2-e2b4a3872a3af6a8307—sucrose———1000——

Extraktionspipeline

Rohextraktionen, Artefakte, Qualitätssignal

Extraktionsqualität

Ehrlichkeitssignal

Bemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.

Parametervollständigkeit

13 %

Anteil der erwarteten Parameter, die extrahiert wurden

Datenvollständigkeit

30 %

Gesamtabdeckung der Extraktion über alle Felder

KI-Konfidenz

78 %

Vom Modell selbst angegebene Konfidenz

Mittlere Parameterkonfidenz

90 %

Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen

vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

07

Quell-PDF

Die Publikation, wie sie erschienen ist.

3D-Modell wird geladen …

Repräsentatives Modell, generisches MFC

Repräsentatives Modell: MFC – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.

MFC
System
840Milliwatt pro Quadratmeter
Bestes Ergebnis · Leistungsdichte
16
Extrahierte Werte
2018
Jahr

Schlagwörter

  • Microbial fuel cell
  • Denitrifying bacteria
  • Denitrification
  • Nitrate
  • Biofilm
  • Wastewater

Zitieren

Xiaojun Jin, Fei Guo, Zhimei Liu et al. (2018). Enhancing the Electricity Generation and Nitrate Removal of Microbial Fuel Cells With a Novel Denitrifying Exoelectrogenic Strain EB-1. Frontiers in Microbiology. https://doi.org/10.3389/fmicb.2018.02633

Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.

Im Labor öffnen