Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation · MDC

Microbial desalination cell with sulfonated sodium poly(ether ether ketone) as cation exchange membranes for enhancing power generation and salt reduction

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

Interaktives 3D-ModellKI-angereichert· 72 %

Zusammenfassung

Microbial desalination cell (MDC) is a bioelectrochemical system capable of oxidizing organics, generating electricity, while reducing the salinity content of brine streams. As it is designed, anion and cation exchange membranes play an important role on the selective removal of ions from the desalination chamber. In this work, sulfonated sodium (Na + ) poly(ether ether ketone) (SPEEK) cation exchange membranes (CEM) were tested in combination with quaternary ammonium chloride poly(2,6-dimethyl 1,4-phenylene oxide) (QAPPO) anion exchange membrane (AEM). Non-patterned and patterned (varying topographical features) CEMs were investigated and assessed in this work. The results were contrasted against a commercially available CEM. This work used real seawater from the Pacific Ocean in the desalination chamber. The results displayed a high desalination rate and power generation for all the membranes, with a maximum of 78.6±2.0% in salinity reduction and 235±7mWm -2 in power generation for the MDCs with the SPEEK CEM. Desalination rate and power generation achieved are higher with synthesized SPEEK membranes when compared with an available commercial CEM. An optimized combination of these types of membranes substantially improves the performances of MDC, making the system more suitable for real applications.

KI-Zusammenfassung

72 % Konfidenz

This paper evaluates sulfonated sodium poly(ether ether ketone) (SPEEK) cation exchange membranes in a three-chamber microbial desalination cell (MDC) using real Pacific seawater. The SPEEK membranes achieved 78.6±2.0% salinity reduction and 235±7 mW m⁻² power density, outperforming commercial membranes by ~20% in power and ~25% in salt removal. Micropatterned SPEEK surfaces (20–80 μm features) did not improve performance over flat membranes, contrary to expectations. The study demonstrates that lower membrane area-specific resistance (ASR) and thickness directly enhance MDC electrochemical performance and desalination rate.

Zentrale Erkenntnisse

  • Zielkonflikt Flat SPEEK CEM (S1) achieved 235±7 mW m⁻² power density, ~20% higher than commercial CEM at 188±11 mW m⁻², despite identical anode performance (max 40 mV difference at 600–700 mA m⁻²).

    Was heißt das. Prioritize thin, high-conductivity membranes over topographical features; membrane resistance dominates cathode polarization, so reducing ASR is the primary lever for power improvement.

  • Schwellenwert Micropatterned SPEEK membranes (S2–S5, 20–80 μm lateral features) showed no power or desalination advantage over flat S1, with power outputs 201–226 mW m⁻² versus 235 mW m⁻² for S1.

    Was heißt das. Do not invest in surface patterning for MDC membranes; the membrane–water interface differs from membrane–air cathode interfaces in fuel cells, and patterning may trap particles or alter ion migration kinetics unfavorably.

  • Mechanismus SPEEK CEMs achieved through-plane resistance of 23–38 Ω cm⁻² in 6 g L⁻¹ NaCl, substantially lower than commercial CMI-7000 at ~30 Ω cm⁻² in 30 g L⁻¹ NaCl, and SPEEK thickness was 50 μm versus 450 μm for commercial.

    Was heißt das. Membrane thickness and ionic conductivity act synergistically to reduce ASR; thin membranes with high conductivity are critical for minimizing ohmic overpotential and maximizing both power and desalination rate.

  • Leistung Salinity reduction with SPEEK membranes was 77.7–78.6% (final conductivity 11–12.8 mS cm⁻¹ from initial 51.4 mS cm⁻¹), a 25% improvement over prior work combining commercial CEM and QAPPO AEM (30.6% removal).

    Was heißt das. Upgrading to lower-resistance membranes yields substantial gains in desalination performance; the improvement is not limited to power but extends to ion removal efficiency.

  • Mechanismus Polarization curves showed linear trends across all membranes, indicating ohmic losses dominate MDC behavior; cathode slope varied with membrane type while anode slope remained constant.

    Was heißt das. Future MDC optimization should focus on reducing ohmic overpotentials (membrane resistance, electrode spacing) rather than kinetic improvements; the system is ohmic-limited, not kinetically limited.

Widersprüche1

Nur Konflikte, die die Publikation selbst zeigt, jeweils am Text geprüft.

  • Gegenüber der Erwartung Patterned membranes were expected to increase interfacial surface area and enhance salt uptake, but instead showed equal or worse performance than flat membranes.

    Eine Seite

    Hypothesis: 'patterning the CEM surface would increase the interfacial surface area between the membrane and the salt water in the desalination chamber...should manifest a lower ohmic resistance and a higher cell power density and greater salt removal'

    “patterning the CEM surface would increase the interfacial surface area between the membrane and the salt water in the desalination chamber. Having an increased interfacial area was anticipated to enhance the rate of salt uptake, which shoul”
    Andere Seite

    Result: 'the patterned membranes did not produce a MDC with greater power density or salt removal when compared to the flat (i.e., non-patterned) CEMs' and 'the through-plane resistance and the in-plane resistance...was equivalent or worse with the patterned membranes'

    “the patterned membranes did not produce a MDC with greater power density or salt removal when compared to the flat (i.e., non-patterned) CEMs. It is important to point out that the through-plane resistance and the in-plane resistance, chara”

    Einordnung der Autoren. Authors attribute failure to particle trapping in patterns or micro-confined domains altering ion migration kinetics. They note the membrane–water interface in MDC differs from the membrane–air cathode interface in PEMFCs where patterning does help.

Ansatzpunkte6

Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.

  • Hoch No systematic study of how SPEEK membrane thickness (currently fixed at 30 μm for flat, cast from PDMS molds) affects power density and desalination rate across a range (e.g., 10–100 μm).

    Text states 'There has not been a systematic study of how membrane attributes impact the Figures of Merit for MDC' and ASR equation (Eq. 4) shows thickness is a direct lever; SPEEK at 50 μm outperformed commercial at 450 μm, but intermediate values were not tested.

    Versuch. Prepare SPEEK CEMs at 10, 20, 30, 50, 75, 100 μm thickness; measure through-plane resistance, power density, and salinity reduction at fixed current density (600–700 mA m⁻²).

  • Hoch No evaluation of SPEEK CEM performance at elevated current densities (>1400 mA m⁻²) or under galvanostatic control to identify operating windows and potential N-species accumulation (NO₂⁻, NO₃⁻, N₂O).

    Paper focuses on polarization curves and power optimization but does not measure nitrogen species in any chamber. Cathode pH and dissolved oxygen are not reported, which are critical for nitrification/denitrification pathways. Text mentions 'low anodic kinetics and high cathodic activation overpotentials' but cathode potential is not explicitly controlled or reported as a variable.

    Versuch. Run MDC at fixed current densities (500, 700, 1000, 1200 mA m⁻²) for 96 h; measure NO₃⁻, NO₂⁻, NH₄⁺, N₂O in all three chambers; record cathode potential, pH, and dissolved oxygen in desalination and cathode chambers.

  • Mittel No investigation of C/N ratio or organic loading effects on desalination and power output; acetate dose is fixed at 3 mL of 100 g L⁻¹ stock (300 mg acetate total) with no variation.

    Anode chamber contains activated sludge and acetate but no analysis of how acetate concentration or C/N ratio affects ion transport or nitrogen cycling. Desalination chamber contains seawater (likely ~0.5 mM NO₃⁻) but no baseline nitrogen speciation is reported.

    Versuch. Vary acetate dose (0.5–3 mL of 100 g L⁻¹ stock) and measure power density, desalination rate, and nitrogen species (NO₃⁻, NO₂⁻, NH₄⁺) in desalination chamber over 96 h.

  • Hoch No measurement of cathode potential, pH, or dissolved oxygen in the desalination and cathode chambers during operation; these are critical for predicting nitrogen cycling pathways.

    Cathode potential is inferred from polarization curves but not reported as a controlled or monitored variable during the 96 h cycles. Text states 'Ag/AgCl (3 M KCl) was used as reference electrode and it was located into the desalination chamber' but no cathode potential values are given. pH is measured at 24 h intervals but not correlated with power or desalination rate.

    Versuch. Install potentiostat with reference electrode in cathode chamber; record cathode potential, pH, and dissolved oxygen continuously during 96 h cycle; correlate with power density and ion transport rates.

  • Mittel No comparison of SPEEK CEM performance with other synthetic low-resistance membranes (e.g., Nafion, other PEEK derivatives, or bipolar membranes) to establish whether SPEEK is optimal or if further improvements are possible.

    Paper compares SPEEK variants (flat vs. patterned) and commercial CMI-7000 only. Text mentions 'Anion and cation exchange membranes, as well as bipolar membranes, were tested in different experiments with MDCs' but does not test bipolar membranes in this work.

    Versuch. Test SPEEK S1 against Nafion 117, Nafion 212, and a bipolar membrane in parallel MDC runs; measure power density, desalination rate, and through-plane resistance under identical conditions.

  • Mittel No long-term stability or fouling study; all experiments are 96 h cycles with fresh electrolytes at the end, so membrane degradation, biofilm formation on membranes, and salt precipitation are not assessed.

    Text notes 'Other notable problems are membrane fouling and chemical degradation, but those topics are not addressed in this report.' Seawater contains organic matter and microbes that may foul SPEEK over extended operation.

    Versuch. Run MDC with S1 membrane for 30 days (720 h) without electrolyte replacement; measure power density, desalination rate, and membrane resistance every 96 h; inspect membrane surface for biofilm and precipitate.

Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

n = 31 extrahierte Werte

Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.

6 von 31 extrahierten Zeilen modellierbar

  • 18 nicht kanonisiert (kein kanonischer Slug)
  • 6 kein SI-Wert
  • 1 widerspricht anderen Publikationen
ParameterWertEinheitKonfidenzQuelleAnmerkungenModellierbar
Power Density204mW m⁻²90 %
extrahiert
"The MDCs having different membranes had a peak of power density of 204 ± 16 mW m…" · T=22°C, pH(an)=7.8, substrate=sodium acetateModellierbar
Short Circuit Current Density1.290mA m⁻²90 %
extrahiert
"The short circuit average currents and the standard deviations (based on n = 3 m…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Power Density226mW m⁻²90 %
extrahiert
"The MDCs having different membranes had a peak of power density of 226 ± 16 mW m…" · T=22°C, pH(an)=7.8, substrate=sodium acetateModellierbar
Short Circuit Current Density1.260mA m⁻²90 %
extrahiert
"The short circuit average currents and the standard deviations (based on n = 3 m…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Short Circuit Current Density1.360mA m⁻²90 %
extrahiert
"a maximum short circuit current of 1399 mA m−2 was measured when S1 membrane was…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Short Circuit Current Density1.200mA m⁻²90 %
extrahiert
"The short circuit average currents and the standard deviations (based on n = 3 m…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Short Circuit Current Density1.250mA m⁻²90 %
extrahiert
"The short circuit average currents and the standard deviations (based on n = 3 m…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Power Density235mW m⁻²90 %
extrahiert
"MDCs with membrane S1 (non-patterned) recorded the highest power density 235 ± 7…" · T=22°C, pH(an)=7.8, substrate=sodium acetateModellierbar
Short Circuit Current Density1.360mA m⁻²90 %
extrahiert
"The short circuit average currents and the standard deviations (based on n = 3 m…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Power Density188mW m⁻²90 %
extrahiert
"Combination of both commercial anion and cation exchange membrane reached 188 ± …" · T=22°C, pH(an)=7.8, substrate=sodium acetateModellierbar
Power Density201mW m⁻²90 %
extrahiert
"The MDCs having different membranes had a peak of power density of 201 ± 19 mW m…" · T=22°C, pH(an)=7.8, substrate=sodium acetateModellierbar
Power Density218mW m⁻²90 %
extrahiert
"The MDCs having different membranes had a peak of power density of 218 ± 13 mW m…" · T=22°C, pH(an)=7.8, substrate=sodium acetateModellierbar
Open Circuit Voltage0,65V90 %
extrahiert
"Initial open circuit voltage (OCV) of the MDCs showed as initial point (null cur…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: widerspricht anderen Publikationen
Anode Chamber Final pH6,8pH90 %
extrahiert
"Activated sludge taken from the same existing batch was used in each cell for th…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Final Desalination Chamber Conductivity11,4mS cm⁻¹90 %
extrahiert
"The results displayed a final solution conductivity that was very similar and co…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Final Desalination Chamber Conductivity11,4mS cm⁻¹90 %
extrahiert
"The results displayed a final solution conductivity that was very similar and co…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Final Desalination Chamber Conductivity35,7mS cm⁻¹90 %
extrahiert
"These results with SPEEK gave a 25% improvement in terms of salt removal respect…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Desalination Rate77,7%90 %
extrahiert
"This corresponded to a reduction in salinity content of 77.7 ± 2.7% for the util…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: kein SI-Wert
Anode Chamber Final Conductivity8mS cm⁻¹90 %
extrahiert
"The solution conductivity at the anode chamber (Fig. 5.c), that had an initial p…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Desalination Rate78,6%90 %
extrahiert
"This corresponded to a reduction in salinity content of 78.6 ± 2% for membrane S…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: kein SI-Wert
Desalination Rate30,6%90 %
extrahiert
"These amounts are much higher than the recorded values by the combination of com…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: kein SI-Wert
Desalination Rate75%90 %
extrahiert
"This corresponded to a reduction in salinity content of 75 ± 1.4% for S4" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: kein SI-Wert
Final Desalination Chamber Conductivity11mS cm⁻¹90 %
extrahiert
"The results displayed a final solution conductivity that was very similar and co…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Cathode Chamber Final pH9,81pH90 %
extrahiert
"In the case of cathode chamber (Fig. 6.b), the initial buffer pH was also 7.8, b…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Anode Chamber Final Conductivity5,45mS cm⁻¹90 %
extrahiert
"The solution conductivity at the anode chamber (Fig. 5.c), that had an initial p…" · T=22°C, pH(an)=7.8, substrate=sodium acetateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
25 von 31 angezeigt

Methodik

Welches System und wie es betrieben wurde

Methodik

Methodology

The MDC consists of three chambers (anode, desalination, cathode) separated by ion-exchange membranes. The anode chamber (33 mL) contains activated sludge and sodium acetate (300 mg total); the desalination chamber (11 mL) contains real Pacific seawater (51.4 mS cm⁻¹); the cathode chamber (33 mL) contains 10 mM potassium phosphate buffer (pH 7.8). The anode is a pre-colonized carbon brush (3 cm diameter, 3 cm height); the cathode is an air-breathing activated carbon/carbon black/PTFE electrode (7 cm² area, 40 mg cm⁻² loading). SPEEK CEMs (flat and micropatterned, 20–80 μm features, 30 μm thickness, 50 μm hydrated) are paired with a QAPPO AEM. Experiments run for 96 h at 470 Ω external resistance; polarization curves are measured after electrolyte replenishment. Conductivity and pH are measured at 24 h intervals. Power density, current density, and salinity reduction are calculated from electrochemical and conductivity data.

Systemkonfiguration

FeldWert
reactor typeMDC
chamber config3-chamber

Betriebsbedingungen

1 Lauf extrahiert
LaufT°CpHAnolytpHKatholytSubstrat[S]mg/LHRThModusR_extΩV_appVInokulum
v2-85337cc6ba00121b227.8—sodium acetate———470——

Extraktionspipeline

Rohextraktionen, Artefakte, Qualitätssignal

Extraktionsqualität

Ehrlichkeitssignal

Bemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.

KI-Konfidenz

72 %

Vom Modell selbst angegebene Konfidenz

Mittlere Parameterkonfidenz

90 %

Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen

vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

07

Quell-PDF

Die Publikation, wie sie erschienen ist.

3D-Modell wird geladen …

Repräsentatives Modell, generisches mikrobielle Entsalzungszelle

Repräsentatives Modell: mikrobielle Entsalzungszelle – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.

MDC
System
235Milliwatt pro Quadratmeter
Bestes Ergebnis · Leistungsdichte
bester von 6
31
Extrahierte Werte
2018
Jahr

Schlagwörter

  • Desalination
  • Membrane
  • Oxidizing agent
  • Ion exchange
  • Ether
  • Chemical engineering

Zitieren

Francisco Lopez Moruno, Juan E. Rubio, Plamen Atanassov et al. (2018). Microbial desalination cell with sulfonated sodium poly(ether ether ketone) as cation exchange membranes for enhancing power generation and salt reduction. Bioelectrochemistry. https://doi.org/10.1016/j.bioelechem.2018.02.004

PubMed
29459302

Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.

Im Labor öffnen