Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation

Increased biological and cathodic hydrogen production using a novel integrated thermophilic fermenter and dual anion exchange membrane bioelectrochemical system

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

KI-angereichert· 72 %

Zusammenfassung

Many researchers are interested in utilizing renewable and sustainable energy made by exoelectrogenic bacteria during electrodialysis for the separation of minerals and organic matters from aqueous environments. The aim of this study was to develop a novel thermophilic fermenter and dual anion exchange membrane bioelectrochemical system for separating biohydrogen production inhibitors from the thermophilic fermenter and thereby increasing biological and cathodic hydrogen production by food waste and wastewater.•Using this innovative system the biohydrogen production inhibitors were separated and nutrients (for example ammonium), alkalinity, buffering capacity and pH were preserved in the bioreactor at the same time, led to higher biological and cathodic hydrogen production.

KI-Zusammenfassung

72 % Konfidenz

This paper describes an integrated thermophilic dark fermentation system coupled to a dual anion exchange membrane bioelectrochemical system (MBES) designed to separate volatile fatty acids (VFAs) while preserving ammonia, alkalinity, and pH in the fermenter. Operating at 55 °C in the fermenter and 35 °C at the anode, with 2.7 V external voltage, the system achieved 632 mL/L higher biohydrogen production than control (63.15 mL/mg vs 50.5 mL/mg yield) and produced 50 mL cathodic hydrogen over 36 h. VFA concentrations increased 3.2–4.5× relative to control by 24–36 h, while ammonium was retained in the dilute chamber through anion exchange membrane selectivity, preventing nutrient depletion.

Zentrale Erkenntnisse

  • Mechanismus VFA accumulation inhibits biohydrogen production in control fermenters, but coupling to the MBES system removed VFAs until 10 h, then stimulated HPB to produce VFAs at 3.2–4.5× the control rate by 24–36 h (Table 4).

    Was heißt das. Operators should expect a biphasic response: initial VFA removal relieves inhibition and boosts H₂ production, but continued electrodialysis operation then drives renewed VFA synthesis, requiring monitoring to decide when to harvest or recycle.

  • Mechanismus Ammonium retention in the dilute chamber (prevented from migrating through AEM to cathode) increased biohydrogen yield from 50.5 to 63.15 mL/mg, a 25% improvement, by avoiding nutrient limitation.

    Was heißt das. Selective cation retention via AEM placement is a key design lever; ensure AEM orientation and chamber layout prevent nutrient loss to non-productive compartments.

  • Mechanismus pH and alkalinity were preserved in the dilute chamber despite fermentation, likely because OH⁻ ions generated at the bipolar membrane migrated into the dilute chamber, counteracting acidification.

    Was heißt das. Bipolar membrane placement and polarity should be optimized to direct OH⁻ generation toward the fermentation chamber; this passive pH buffering reduces need for external base addition.

  • Zielkonflikt Cathodic hydrogen production was modest (50 mL over 36 h) compared to biohydrogen (632 mL/L higher than control), indicating the system prioritizes fermentation enhancement over electrochemical H₂ synthesis.

    Was heißt das. If cathodic H₂ is a priority, increase applied voltage or cathode surface area; current 2.7 V external voltage is optimized for VFA separation and fermentation support, not electrochemical H₂ production.

  • Schwellenwert Operating temperature differs between fermenter (55 °C thermophilic) and anode chamber (35 °C mesophilic), creating a thermal gradient that may affect microbial community composition and electron transfer kinetics.

    Was heißt das. Validate that mesophilic anode biofilm remains electrochemically active when fed substrate from a thermophilic fermenter; consider whether temperature homogenization or staged cooling would improve performance.

Ansatzpunkte6

Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.

  • Hoch No measurement of N-species (NO₃⁻, NO₂⁻, NH₄⁺-N, N₂O) in cathode or anode chambers; nitrogen cycling pathways are not characterized despite ammonium being a key nutrient preserved.

    Paper emphasizes ammonium retention as a driver of improved biohydrogen yield, but provides no data on whether ammonium is oxidized, reduced, or remains stable in the MBES chambers. Cathode chamber conditions (pH 6.5–6.6, applied voltage, electron availability) could support denitrification or nitrification, which would compete with H⁺ reduction.

    Versuch. Measure NH₄⁺, NO₃⁻, NO₂⁻, and N₂O in anode, cathode, and dilute chambers over 36 h operation; vary applied voltage (2.0–3.5 V) and cathode pH (6.0–8.0) to map nitrogen fate.

  • Hoch No systematic variation of applied voltage or current density; single operating point (2.7 V) tested, leaving the trade-off between VFA separation efficiency, H₂ production, and energy input unmapped.

    Text states 2.7 V was used 'to overcome system internal resistance of BPM' but does not justify this value or explore whether lower voltage reduces energy cost while maintaining VFA removal, or higher voltage boosts cathodic H₂.

    Versuch. Operate integrated system at 1.8, 2.3, 2.7, 3.2 V; measure VFA removal rate, biohydrogen yield, cathodic H₂, and energy recovery (H₂ energy output / electrical input) to identify optimal voltage window.

  • Mittel Hydraulic retention time (HRT) in the dilute chamber and overall MBES residence time not specified; unclear whether VFA removal kinetics are diffusion-limited, electromigration-limited, or reaction-limited.

    Fermenter mixed solution flow rate into dilute chamber is not stated. Chamber volumes are given (200 mL anode, 80 mL others) but no flow rate, so HRT cannot be calculated. This prevents comparison with other electrodialysis studies and limits reproducibility.

    Versuch. Vary dilute chamber residence time (HRT = 2, 4, 8, 12 h) by adjusting fermenter recirculation flow rate; measure VFA removal rate (mg/L/h) and biohydrogen production to identify optimal HRT.

  • Mittel No measurement of dissolved oxygen (DO) in any chamber; anaerobic conditions are assumed but not verified, despite N₂ sparging being the only oxygen control method.

    Text states 'All bioelectrochemical system chambers and fermenters were purged with N₂ before each run' but no DO probe data or post-purge verification is provided. Cathode chamber in particular could accumulate O₂ from water oxidation or air ingress, affecting electron transfer and potentially enabling aerobic nitrification.

    Versuch. Install DO probes in anode, cathode, and dilute chambers; measure DO over 36 h operation; correlate DO with biofilm current output and H₂ production rate.

  • Mittel Microbial community composition not characterized; unclear whether thermophilic fermenter and mesophilic anode biofilm are stable or whether temperature mismatch causes washout or metabolic stress.

    Paper uses pre-heated sludge inoculum and reports 2-month biofilm acclimation to reach 700 mV open-circuit voltage, but does not provide 16S rRNA or metagenomic data. Anode operates at 35 °C while fermenter is 55 °C; no evidence that the anode biofilm remains active or that exoelectrogens are retained.

    Versuch. Perform 16S rRNA gene sequencing of anode biofilm and fermenter liquid at 0, 12, 24, 36 h; compare community structure to mesophilic and thermophilic controls; measure anode current density over time to assess biofilm stability.

  • Mittel C/N ratio of feedstock not optimized; food waste has very low TKN (30 mg/L) relative to COD (199,500 mg/L), creating a C/N ratio of ~6,650:1, far above typical fermentation optima (20–30:1).

    Table 1 shows food waste TKN = 30 mg/L and COD = 199,500 mg/L. Nutrient stock solution is added (Table 2) but final C/N ratio in fermenter is not calculated. Paper states ammonium concentration increased due to AEM retention, but does not test whether higher initial N loading or lower C/N ratio would further boost biohydrogen yield or change VFA profile.

    Versuch. Prepare feedstocks with C/N ratios of 50:1, 100:1, 200:1, and 400:1 by adjusting food waste:sludge ratio or adding NH₄Cl; measure biohydrogen yield, VFA composition (acetate vs. propionate vs. butyrate), and ammonium dynamics in integrated system.

Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

n = 16 extrahierte Werte

Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.

6 von 16 extrahierten Zeilen modellierbar

  • 7 nicht kanonisiert (kein kanonischer Slug)
  • 3 kein SI-Wert
ParameterWertEinheitKonfidenzQuelleAnmerkungenModellierbar
Volatile Fatty Acids631mg/L90 %
extrahiert
"36 2511.7 ( ±112) 59.7 ( ±9) 630.9 ( ±55) 3202.3 ( ±176)" · T=55°C, pH(an)=6.5, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Modellierbar
Volatile Fatty Acids59,7mg/L90 %
extrahiert
"36 2511.7 ( ±112) 59.7 ( ±9) 630.9 ( ±55) 3202.3 ( ±176)" · T=55°C, pH(an)=6.5, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Modellierbar
Volatile Fatty Acids144mg/L90 %
extrahiert
"24 144.3 ( ±6) 63.2 ( ±5) 507 ( ±43) 714.5 ( ±54)" · T=55°C, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Modellierbar
Volatile fatty acids concentration in separation chamber0,51g/L90 %
extrahiert
"Volatile fatty acids concentration was raised up to 0.51 g L −1 in the volatile …" · T=55°C, pH(an)=6.5, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Biohydrogen yield63,2mL/mg90 %
extrahiert
"In our work, biohydrogen production yield was enhanced to 63.15 mL mg −1 versus …" · T=55°C, pH(an)=6.5, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Specific H₂ Production4.140mL/L90 %
extrahiert
"36 2511.7 ( ±112) 59.7 ( ±9) 630.9 ( ±55) 3202.3 ( ±176)" · T=55°C, pH(an)=6.5, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Ausgeschlossen: kein SI-Wert
Cathodic hydrogen produced50mL90 %
extrahiert
"Furthermore, in our system, 50 mL cathodic hydrogen ( Fig. S5 ) was produced aft…" · T=55°C, pH(an)=6.5, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Total VFAs concentration3.200mg/L90 %
extrahiert
"36 2511.7 ( ±112) 59.7 ( ±9) 630.9 ( ±55) 3202.3 ( ±176)" · T=55°C, pH(an)=6.5, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Biohydrogen production increase versus control632mL/L90 %
extrahiert
"Biohydrogen production was 632 mL L −1 higher rather than the control run, accor…" · T=55°C, pH(an)=6.5, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Volatile Fatty Acids2.510mg/L90 %
extrahiert
"36 2511.7 ( ±112) 59.7 ( ±9) 630.9 ( ±55) 3202.3 ( ±176)" · T=55°C, pH(an)=6.5, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Modellierbar
Total VFAs concentration715mg/L90 %
extrahiert
"24 144.3 ( ±6) 63.2 ( ±5) 507 ( ±43) 714.5 ( ±54)" · T=55°C, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Volatile Fatty Acids63,2mg/L90 %
extrahiert
"24 144.3 ( ±6) 63.2 ( ±5) 507 ( ±43) 714.5 ( ±54)" · T=55°C, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Modellierbar
Volatile Fatty Acids507mg/L90 %
extrahiert
"24 144.3 ( ±6) 63.2 ( ±5) 507 ( ±43) 714.5 ( ±54)" · T=55°C, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Modellierbar
Biohydrogen yield50,5mL/mg90 %
extrahiert
"In our work, biohydrogen production yield was enhanced to 63.15 mL mg −1 versus …" · T=55°C, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Specific H₂ Production2.880mL/L90 %
extrahiert
"70C 0 192.6 ( ±9) 24 ( ±3) 32 ( ±3) 248.6 ( ±15) 2879 ( ± 32)" · T=55°C, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Ausgeschlossen: kein SI-Wert
Specific H₂ Production3.510mL/L90 %
extrahiert
"70- 2AEM 0 193 ( ±8) 40.2 ( ±6) 41.9 ( ±65) 274.2 ( ±20) 3511 ( ±35)" · T=55°C, pH(an)=6.5, substrate=food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)Ausgeschlossen: kein SI-Wert

Methodik

Welches System und wie es betrieben wurde

Methodik

Methodology

The system integrates a 0.5 L thermophilic dark fermenter (55 °C, 0.45 L working volume) fed with diluted food waste and pre-heated anaerobic sludge, coupled via a dual anion exchange membrane bioelectrochemical system (MBES) consisting of anode (carbon felt, 3.5 cm × 10 cm × 0.5 cm), cathode (stainless-steel mesh, 4 cm × 10 cm), two bipolar membranes (BPM) at 2 mm from electrodes, and two anion exchange membranes (AEM) at 2.5 cm spacing. The anode chamber (200 mL) operates at 35 °C mesophilic conditions with a pre-acclimated biofilm; the dilute chamber (80 mL) receives fermenter liquid; and the cathode chamber (80 mL) is supplied with 0.2 M NaCl electrolyte (pH 6.5–6.6). External voltage of 2.7 V is applied via DC power supply. Biohydrogen, cathodic hydrogen, volatile fatty acids (acetate, propionate, butyrate), ammonium, COD, alkalinity, and pH are measured at 6, 8, 12, 24, and 36 h.

Systemkonfiguration

FeldWert
reactor typeMBES
chamber config5-chamber

Betriebsbedingungen

2 Läufe extrahiert
LaufT°CpHAnolytpHKatholytSubstrat[S]mg/LHRThModusR_extΩV_appVInokulum
v2-178146c51da45e4b556.5—food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)———10——
v2-ef97e3bcae8e664255——food waste (vegetable residues 54%, fruit peel 30%, meat 2%, boiled rice 10%, bread 5%)——————

Extraktionspipeline

Rohextraktionen, Artefakte, Qualitätssignal

Extraktionsqualität

Ehrlichkeitssignal

Bemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.

KI-Konfidenz

72 %

Vom Modell selbst angegebene Konfidenz

Mittlere Parameterkonfidenz

90 %

Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen

vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

07

Quell-PDF

Die Publikation, wie sie erschienen ist.

Dieser Publikation ist noch kein 3D-Modell zugeordnet. Die daraus extrahierten Werte stehen unter „Extrahierte Werte“.

16
Extrahierte Werte
2022
Jahr

Schlagwörter

  • Biohydrogen
  • Industrial fermentation
  • Electrodialysis
  • Microbial fuel cell
  • Wastewater
  • Bioreactor

Zitieren

Nadali Alavi, Monireh Majlessi, Nazak Amanidaz et al. (2022). Increased biological and cathodic hydrogen production using a novel integrated thermophilic fermenter and dual anion exchange membrane bioelectrochemical system. MethodsX. https://doi.org/10.1016/j.mex.2022.101770

PubMed
35818447
Zeitschrift
MethodsX