Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation · MEC

Combined anaerobic - aerobic bioelectrochemical system for ammonium sulfide and carbon removal from ethanol stillage

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

Interaktives 3D-ModellKI-angereichert· 72 %

KI-Zusammenfassung

72 % Konfidenz

This study integrated a two-chamber bioelectrochemical system (BES) with anaerobic and aerobic bioreactors to treat ethanol stillage, comparing five operating modes: no BES, MFC, and MEC at 0.6, 0.8, and 1.0 V. MEC at 1.0 V achieved 94.1% COD removal and 90.91% NH4+-N removal, with methane content rising from 57% (no BES) to 74% (MEC). Sulfate removal reached 100% in MEC modes versus 8.74% without BES. The cation exchange membrane enabled ammonium migration to the cathode where nitrification and denitrification occurred, improving both energy recovery and pollutant removal.

Zentrale Erkenntnisse

  • Schwellenwert Applied voltage directly controls ammonium removal efficiency: 1.0 V achieved 90.91% NH4+-N removal versus 53.58% without BES, a 1.7× improvement.

    Was heißt das. Operators targeting high ammonia recovery should apply ≥0.8 V external voltage; below 0.6 V, removal plateaus near 67–69%.

  • Schwellenwert Sulfate removal shows a sharp on/off transition: MFC achieved 72.71% SO4²⁻ removal, but all three MEC modes achieved 100% removal regardless of voltage (0.6–1.0 V).

    Was heißt das. Sulfide oxidation at the anode is voltage-independent above ~0.6 V; MEC operation is sufficient for complete sulfate removal without voltage optimization.

  • Zielkonflikt COD removal efficiency increases with applied voltage in MEC but plateaus in MFC: MEC1.0V achieved 94.1% versus MFC's 69.82%, a 1.35× gain.

    Was heißt das. For maximum organic matter degradation, use MEC at ≥0.8 V; MFC mode offers minimal advantage over anaerobic digestion alone (69.82% vs 56.57%).

  • Schwellenwert Methane content improves in all BES modes but saturates: MFC reached 70 vol.%, MEC0.6V 72%, and MEC0.8V/1.0V both 74%, suggesting a ceiling near 74%.

    Was heißt das. Biogas quality improvement plateaus at MEC0.6V; higher voltages improve COD/NH4+ removal but not gas composition further.

  • Mechanismus Current density scales linearly with applied voltage in MEC but remains low in MFC: MEC1.0V reached 1.5–2.9 A/m² versus MFC's 0.01–0.02 A/m², a 100–150× difference.

    Was heißt das. MEC operation drives substantially higher electron transfer rates; if anode biofilm kinetics are limiting, MEC will unlock higher throughput than MFC.

Ansatzpunkte6

Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.

  • Hoch No measurement of nitrite (NO2⁻) or N2O accumulation in cathode or aerobic reactor effluent despite nitrification/denitrification occurring.

    Paper states 'nitrification in the zone of the aerobic bioreactor' and 'nitrate reduction takes place' at cathode, but provides no data on intermediate nitrogen oxides. N2O is a potent greenhouse gas and nitrite can inhibit methanogenesis.

    Versuch. Measure NO2⁻ and N2O in aerobic reactor outlet and cathode effluent across 0.6–1.0 V range; quantify by ion chromatography and gas chromatography.

  • Hoch No systematic variation of cathode pH or dissolved oxygen (DO) in aerobic reactor; both are known to control nitrification/denitrification selectivity.

    Paper reports 'pH 7.5–7.6' as fixed input but does not report cathode pH or aerobic reactor DO. Nitrification rate and N2O yield are highly pH and DO sensitive.

    Versuch. Vary cathode pH (6.5–8.5) and aerobic reactor DO (2–8 mg/L) at fixed 0.8 V; measure NH4⁺ removal, NO3⁻ accumulation, and N2O flux.

  • Mittel No exploration of C/N ratio effects; ethanol stillage has fixed TKN (302–315 mg/L) but only one dilution tested.

    Paper dilutes stillage 4× to achieve ~10 g/L COD but does not test whether lower or higher C/N ratios improve nitrogen removal or reduce N2O.

    Versuch. Test 2×, 4×, and 8× dilutions (varying C/N from ~30 to ~120 on COD:TKN basis); measure NH4⁺ removal and NO3⁻/NO2⁻ accumulation at 0.8 V.

  • Mittel No measurement of anode or cathode potential (vs. Ag/AgCl or SHE); only external voltage applied is reported.

    Paper applies 0.6–1.0 V external voltage but does not report actual electrode potentials. Anode potential controls sulfide oxidation pathway (S⁰ vs. SO4²⁻); cathode potential controls denitrification selectivity (NO3⁻ → NO2⁻ → N2O → N2).

    Versuch. Insert reference electrodes; measure anode and cathode potential vs. Ag/AgCl at each external voltage; correlate with sulfide speciation and nitrogen product distribution.

  • Mittel No investigation of HRT trade-offs; fixed 11-day anaerobic and 6-day aerobic HRT may not be optimal for nitrogen cycling.

    Paper states contact times but does not vary them. Shorter HRT may increase throughput but reduce nitrification/denitrification completeness; longer HRT may accumulate inhibitory ammonia.

    Versuch. Vary anaerobic HRT (5–15 days) and aerobic HRT (3–9 days) at 0.8 V; measure NH4⁺ removal, NO3⁻ accumulation, and methane yield.

  • Mittel No characterization of biofilm composition or electroactive bacteria (EAB) abundance on anode/cathode; mechanism of improved removal is inferred but not verified.

    Paper attributes sulfide oxidation and COD removal to EAB but provides no 16S rRNA, qPCR, or microscopy data. Unclear whether Geobacter, Shewanella, or other taxa dominate.

    Versuch. Sample anode and cathode biofilms at days 3, 7, and 11; perform 16S rRNA gene sequencing and qPCR for known EAB; correlate abundance with current density and removal efficiency.

Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

n = 201 extrahierte Werte

Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.

81 von 200 extrahierten Zeilen modellierbar

  • 85 nicht kanonisiert (kein kanonischer Slug)
  • 34 kein SI-Wert
ParameterWertEinheitKonfidenzQuelleAnmerkungenModellierbar
Substrateethanol—80 %
llm
Chemical oxygen demand (COD) anode zone0,9g/L90 %
cod (hanna reagents, apha)
"COD anode 0.9 g/L (AD-MEC_0.8V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) removal efficiency69,8%90 %
extrahiert
"When the BES works as an MFC, the COD removal efficiency is 69.82 %" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Sulfate removal efficiency72,7%90 %
extrahiert
"SO42- content decreases by 72.71 % (MFC)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Methane content70vol %90 %
extrahiert
"In MFC mode, the methane content rises to 70 %" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) cathode zone1,15g/L90 %
cod (hanna reagents, apha)
"COD cathode 1.152 g/L (AD-MFC)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Hydrogen sulfide liquid13,9mg/L90 %
spectrophotometric (nanocolor test, 620 nm)
"H2S in liquid 13.89 mg/L (AD-MFC)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Hydrogen sulfide liquid4,65mg/L90 %
spectrophotometric (nanocolor test, 620 nm)
"H2S in liquid 4.65 mg/L (AD-MEC_1.0V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Ammonium cathode zone30,5mg/L90 %
kjeldahl (udk 127)
"NH4+ cathode 30.5 mg/L (AD-MEC_0.8V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) cathode zone0,5g/L90 %
cod (hanna reagents, apha)
"COD cathode 0.5 g/L (AD-MEC_0.8V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Sulfate removal efficiency8,74%90 %
extrahiert
"removal rate 8.74 % (without BES)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) removal efficiency56,6%90 %
extrahiert
"without BES ... only 56.57 %" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Ammonium removal efficiency53,6%90 %
extrahiert
"without BES - only 53.58 %" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Ammonium anode zone125mg/L90 %
kjeldahl (udk 127)
"NH4+ anode 125 mg/L (AD-MEC_0.8V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) anode zone2,78g/L90 %
cod (hanna reagents, apha)
"COD anode 2.78 g/L (AD-MFC)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) anode zone0,59g/L90 %
cod (hanna reagents, apha)
"COD anode 0.59 g/L (AD-MEC_1.0V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Ammonium removal efficiency90,9%90 %
extrahiert
"best removal ... MEC 1.0 V (90.91 %)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Ammonium cathode zone45,5mg/L90 %
kjeldahl (udk 127)
"NH4+ cathode 45.5 mg/L (AD-MEC_0.6V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Ammonium anode zone139mg/L90 %
kjeldahl (udk 127)
"NH4+ anode 139.1 mg/L (AD-MEC_0.6V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) removal efficiency91%90 %
extrahiert
"91 % at MEC0.8V" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) anode zone1,4g/L90 %
cod (hanna reagents, apha)
"COD anode 1.4 g/L (AD-MEC_0.6V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) cathode zone0,098g/L90 %
cod (hanna reagents, apha)
"COD cathode 0.098 g/L (AD-MEC_1.0V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Ammonium anode zone109mg/L90 %
kjeldahl (udk 127)
"NH4+ anode 108.9 mg/L (AD-MEC_1.0V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) cathode zone0,8g/L90 %
cod (hanna reagents, apha)
"COD cathode 0.8 g/L (AD-MEC_0.6V)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Chemical oxygen demand (COD) cathode zone2,19g/L90 %
cod (hanna reagents, apha)
"COD cathode 2.192 g/L (without_BES)" · pH(an)=7.5, substrate=Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor, HRT=264h, continuousAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
25 von 133 angezeigt

Methodik

Welches System und wie es betrieben wurde

Methodik

Methodology

A two-chamber BES with cation exchange membrane (CMI-7000S) was integrated in series with an anaerobic digester (UASB, 3 L, 11-day HRT) and aerobic bioreactor (1.5 L, 6-day HRT). Ethanol stillage (diluted 4×, ~10 g/L COD, 302–315 mg/L TKN) was fed daily (273 mL/day). The anode received recirculated anaerobic effluent; the cathode received recirculated aerobic effluent. Five modes were tested: no BES (control), MFC (100 Ω load), and MEC at 0.6, 0.8, and 1.0 V external voltage. Measurements included COD, NH4⁺-N, SO4²⁻, H2S, biogas composition (CH4, CO2, H2, H2S), current density, and power density over 11 days.

Systemkonfiguration

FeldWert
reactor typeBES
chamber config2-chamber

Betriebsparameter

FeldWert
substrate["ethanol"]

Betriebsbedingungen

11 Läufe extrahiert
LaufT°CpHAnolytpHKatholytSubstrat[S]mg/LHRThModusR_extΩV_appVInokulum
cma:AD-MEC_0.6V—7.5—Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor10264continuous100.6Aerobic and anaerobic activated sludge from 'Almagest' AD, Verinsko village, Bulgaria
cma:AD-MEC_0.8V—7.5—Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor10264continuous100.8Aerobic and anaerobic activated sludge from 'Almagest' AD, Verinsko village, Bulgaria
cma:AD-MEC_1.0V—7.5—Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor10264continuous101Aerobic and anaerobic activated sludge from 'Almagest' AD, Verinsko village, Bulgaria
cma:AD-MFC—7.5—Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor9.21264continuous100—Aerobic and anaerobic activated sludge from 'Almagest' AD, Verinsko village, Bulgaria
cma:without_BES—7.5—Ethanol stillage (winery vinasse), neutralized to pH 7.5 with NaOH and diluted 4x; fed to anaerobic (UASB) reactor9.21264continuous——Aerobic and anaerobic activated sludge from 'Almagest' AD, Verinsko village, Bulgaria
v2-11fcd14d69b1393a—7.5—ethanol stillage——steady_state100.6—
v2-2a37beaa2f183569—7.5—ethanol stillage——steady_state100.8—
v2-4b8991a5a38af0d4—7.5—ethanol stillage——steady_state101—
v2-58966c17a300ee9e—7.5—ethanol stillage——steady_state———
v2-6e28f9a9a1915b3c—7.5—ethanol stillage——steady_state100——
v2-f69fa4f4d22bbc06—7.5—ethanol stillage——startup100——

Extraktionspipeline

Rohextraktionen, Artefakte, Qualitätssignal

Extraktionsqualität

Ehrlichkeitssignal

Bemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.

Parametervollständigkeit

13 %

Anteil der erwarteten Parameter, die extrahiert wurden

Datenvollständigkeit

30 %

Gesamtabdeckung der Extraktion über alle Felder

KI-Konfidenz

72 %

Vom Modell selbst angegebene Konfidenz

Mittlere Parameterkonfidenz

89 %

Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen

vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

07

Quell-PDF

Die Publikation, wie sie erschienen ist.

3D-Modell wird geladen …

Repräsentatives Modell, generisches MEC

Repräsentatives Modell: MEC – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.

MEC
System
50100Milliwatt pro Quadratmeter
Bestes Ergebnis · Leistungsdichte
bester von 2
201
Extrahierte Werte
2023
Jahr

Schlagwörter

  • Stillage
  • Anaerobic exercise
  • Sulfide
  • Ethanol
  • Ammonium
  • Carbon fibers

Zitieren

Polina Velichkova, Anatoliy Angelov, Svetlana Bratkova (2023). Combined anaerobic - aerobic bioelectrochemical system for ammonium sulfide and carbon removal from ethanol stillage. Journal of Chemical Technology and Metallurgy. https://doi.org/10.59957/jctm.v58i2.53

Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.

Im Labor öffnen