Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation · MDC

Accomplishing a N-E-W (nutrient-energy-water) synergy in a bioelectrochemical nitritation-anammox process

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

Interaktives 3D-ModellKI-angereichert· 82 %Substrat ·pure compound

Zusammenfassung

Abstract This study reports an investigation of the concept, application and performance of a novel bioelectrochemical nitritation-anammox microbial desalination cell (MDC) for resource-efficient wastewater treatment and desalination. Two configurations of anammox MDCs (anaerobic-anammox cathode MDC (AnA mox MDC) and nitration-anammox cathode MDC (NiA mox MDC)) were compared with an air cathode MDC (CMDC), operated in fed-batch mode. Results from this study showed that the maximum power density produced by NiA mox MDC (1,007 mW/m 3 ) was higher than that of AnA mox MDC (444 mW/m 3 ) and CMDC (952 mW/m 3 ). More than 92% of ammonium-nitrogen (NH 4 + -N) removal was achieved in NiA mox MDC, significantly higher than AnA mox MDC (84%) and CMDC (77%). The NiA mox MDC performed better than CMDC and AnA mox MDC in terms of power density, COD removal and salt removal in desalination chamber. In addition, cyclic voltammetry analysis of anammox cathode showed a redox peak centered at −140 mV Vs Ag/AgCl confirming the catalytic activity of anammox bacteria towards the electron transfer process. Further, net energy balance of the NiA mox MDC was the highest (NiA mox MDC-0.022 kWh/m 3 >CMDC-0.019 kWh/m 3 >AnA mox MDC-0.021 kWh/m 3 ) among the three configurations. This study demonstrated, for the first time, a N-E-W synergy for resource-efficient wastewater treatment using nitritation-anammox process.

KI-Zusammenfassung

82 % Konfidenz

This study demonstrates a bioelectrochemical nitritation-anammox microbial desalination cell (NiAmoxMDC) that couples partial nitrification, anammox, and desalination in a single system. The NiAmoxMDC achieved 92% NH₄⁺-N removal and 1,007 mW/m³ power density, outperforming an anaerobic anammox MDC (444 mW/m³, 84% removal) and air cathode control (952 mW/m³, 77% removal). However, aeration at 10 ml/min caused NO₂⁻-N accumulation (6.3–10.3 mg/L) and anammox inhibition by cycles 3–4, which was partially reversed by reducing aeration to 3 ml/min. The system achieved near energy-neutral operation (−0.022 kWh/m³) with 54% salt removal.

Zentrale Erkenntnisse

  • Schwellenwert Aeration at 10 ml/min caused NO₂⁻-N accumulation from 0 to 10.3 mg/L over 4 cycles and reduced NH₄⁺-N removal from 98.3% to 78.6%, indicating anammox inhibition under aerobic stress.

    Was heißt das. Operators must reduce aeration to 3 ml/min (DO ~1.6 mg/L) to maintain anammox activity and prevent nitrite accumulation, even though this reduces power density.

  • Zielkonflikt Reducing aeration from 10 to 3 ml/min increased total nitrogen removal by 66.6% (from ~25% to 75%) in NiAmoxMDC, demonstrating a critical operating window for nitritation-anammox balance.

    Was heißt das. Design cathode aeration control to maintain low DO (1.6 mg/L) rather than maximizing oxygen transfer; this is the key trade-off between power and nitrogen removal.

  • Mechanismus NiAmoxMDC generated 1,007 mW/m³ with two terminal electron acceptors (O₂ reduction + anammox NO₂⁻ reduction), compared to 444 mW/m³ for anaerobic anammox alone, a 2.3× improvement.

    Was heißt das. Aerated biocathodes with anammox can generate higher power than anaerobic anammox alone, but only if aeration is controlled to prevent anammox inhibition.

  • Mechanismus Ohmic resistance in anaerobic AnAmoxMDC was 97.3 Ω versus 50.1 Ω in aerated NiAmoxMDC, a 1.94× difference attributed to biofouling of ion exchange membranes under anaerobic conditions.

    Was heißt das. Maintain cathode aeration not only for nitritation but also to reduce membrane biofouling and ohmic losses; this improves both nitrogen removal and electrical performance.

  • Leistung Coulombic efficiency remained low (17–26%) despite high COD removal (62–72%), because glucose is fermentable and supports competing non-electrochemical pathways (fermentation, methanogenesis).

    Was heißt das. For future work, test with less fermentable substrates (e.g., acetate) to improve CE and validate whether the power and nitrogen removal gains hold under higher CE conditions.

Widersprüche2

Nur Konflikte, die die Publikation selbst zeigt, jeweils am Text geprüft.

  • Innerhalb der Publikation Aeration improves power and reduces ohmic resistance, but inhibits anammox and causes nitrite accumulation.

    Eine Seite

    NiAmoxMDC at 10 ml/min aeration: 1,007 mW/m³ power, 50.1 Ω ohmic resistance, 92% NH₄⁺-N removal in cycles 1–2

    “The maximum power density produced by NiAmoxMDC (1,007 mW/m³) was higher than that of AnAmoxMDC (444 mW/m³)”
    Andere Seite

    Same system cycles 3–4: NO₂⁻-N accumulation to 10.3 mg/L, NH₄⁺-N removal drops to 78.6%, anammox inhibited

    “accumulation of NO₂⁻-N and decrease in the removal rates of NH₄⁺-N in third and fourth cycles confirmed the inhibition effect on the anammox process due to continued exposure of anammox bacteria to aerobic condition”

    Einordnung der Autoren. Authors attribute this to oxygen toxicity to anammox bacteria over time; the solution is to reduce aeration to 3 ml/min, which restores 75% TN removal but likely reduces power. This is a fundamental trade-off, not a true contradiction, but the paper does not quantify power at 3 ml/min aeration.

  • Innerhalb der Publikation Coulombic efficiency is low despite high COD removal, suggesting most organic matter is not converted to electricity.

    Eine Seite

    COD removal 72.1% in NiAmoxMDC

    “COD removal efficiency was significantly higher in NiAmoxMDC (ANOVA, p < 0.0001)”
    Andere Seite

    Coulombic efficiency only 25.6% in NiAmoxMDC

    “the CE of NiAmoxMDC was only 25 ± 6.4%, indicating that a substantial portion of COD utilization was not associated with electron release”

    Einordnung der Autoren. Authors explain this is due to glucose fermentation and methanogenesis competing with electrochemical oxidation. This is expected for glucose but limits the energy-positive claim; the paper does not test non-fermentable substrates.

Ansatzpunkte6

Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.

  • Hoch Aeration rate and dissolved oxygen setpoint were not systematically varied; only two points tested (10 ml/min and 3 ml/min). Optimal DO window for balancing nitritation, anammox activity, and power generation is unknown.

    Paper shows 10 ml/min causes anammox inhibition by cycle 3–4 (NO₂⁻-N rises to 10.3 mg/L), but 3 ml/min restores 75% TN removal. No intermediate points (5, 7 ml/min) or DO targets (0.5, 1.0, 2.0 mg/L) tested. Power density at 3 ml/min not reported.

    Versuch. Vary aeration rate (2–10 ml/min) or set DO setpoint (0.5–3.0 mg/L) in fed-batch cycles; measure power density, NH₄⁺-N removal, NO₂⁻-N accumulation, and anammox activity (e.g., N₂ production rate) at each point.

  • Hoch Substrate choice (glucose) is highly fermentable and suppresses coulombic efficiency to 25.6%. No comparison with acetate or other less fermentable substrates.

    Text states: 'glucose was used as an organic substrate...fermentable substrate, which implies its possible consumption by diverse competing metabolisms such as fermentation and methanogens that do not contribute towards columbic efficiency.' Supplementary Table S3 compares to other nitritation-anammox systems but not to MES systems using acetate.

    Versuch. Run parallel NiAmoxMDC fed-batch cycles with acetate (10–20 mM) at same aeration (3 ml/min); measure power density, CE, COD removal, and nitrogen removal to determine if substrate choice is the limiting factor.

  • Mittel Hydraulic retention time (HRT) and batch cycle duration not specified; fed-batch mode means HRT varies. No kinetic data on nitritation or anammox rates.

    Paper states 'operated in fed-batch mode' but does not report cycle duration, volume exchanged per cycle, or HRT. Supplementary Table S2 shows removal rates per cycle but not per hour. Nitritation-anammox kinetics (e.g., specific nitritation rate, anammox rate) not measured.

    Versuch. Report cycle duration and HRT; measure time-course of NH₄⁺-N, NO₂⁻-N, NO₃⁻-N, and N₂ production within a single cycle to quantify nitritation and anammox kinetics at 3 ml/min aeration.

  • Mittel N₂ production (the desired end product of anammox) was not directly measured. Nitrogen balance relies on mass balance (input NH₄⁺ + NO₂⁻ minus output NH₄⁺ + NO₂⁻ + NO₃⁻).

    Text states anammox oxidizes ammonium to nitrogen gas, but no N₂ measurement (e.g., gas chromatography, ¹⁵N tracing) provided. Nitrogen recovery is inferred from disappearance of NH₄⁺ and NO₂⁻, but some may be assimilated into biomass or lost as N₂O.

    Versuch. Measure N₂ production by headspace gas chromatography or ¹⁵N-labeled batch experiments; quantify N₂O production to confirm anammox selectivity and rule out competing denitrification pathways.

  • Mittel Cathode potential (vs. SHE or Ag/AgCl) during operation not reported; only redox peak from cyclic voltammetry (−140 mV vs Ag/AgCl) provided. Operating cathode potential window unknown.

    CV shows redox peak but not the steady-state cathode potential during fed-batch operation. Polarization curves (Fig. 2B) show voltage but not electrode potentials. No data on how cathode potential affects nitritation vs. anammox selectivity.

    Versuch. Measure cathode potential (vs. Ag/AgCl reference) during fed-batch cycles at 3 ml/min aeration; correlate with NH₄⁺-N removal, NO₂⁻-N accumulation, and power output to define optimal operating window.

  • Niedrig Desalination performance limited by low ion exchange membrane (IEM) surface area ratio (0.8:1 cm²/cm³) and volumetric ratio (1.5 v/v). Scaling factors for salt removal not explored.

    Text states: 'At a higher volumetric ratio of 100 (v/v)...93% salt removal was reported' vs. 53.9% in this study at 1.5 v/v. Authors acknowledge this but do not test higher ratios or larger IEM areas.

    Versuch. Increase volumetric ratio to 5–10 (v/v) and IEM surface area ratio to ≥2 (cm²/cm³); measure salt removal and power density to determine if desalination can be improved without sacrificing nitrogen removal.

Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

n = 142 extrahierte Werte

Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.

78 von 141 extrahierten Zeilen modellierbar

  • 30 nicht kanonisiert (kein kanonischer Slug)
  • 21 kein SI-Wert
  • 6 außerhalb physikalischer Grenzen
  • 4 nicht als modellierbar markiert
  • 2 Verifizierer hat den Wert abgelehnt
ParameterWertEinheitKonfidenzQuelleAnmerkungenModellierbar
Substratewastewater—80 %
llm
Standard Potential×2-140mV Vs Ag/AgCl95 %
cyclic voltammetry
"cyclic voltammetry analysis of anammox cathode showed a redox peak centered at −…" · T=22°C, steady_stateAusgeschlossen: nicht als modellierbar markiert
Chemical Oxygen Demand (COD) Removal×272,1%95 %
cod assay (closed-reflux)
"and NiAmoxMDC over the fed-batch cycles were 65.8 ± 1.56% (n = 8; SD = 1.56), 62…" · T=22°C, substrate=glucose, steady_stateModellierbar
Salt Removal×243%95 %
conductivity measurement
"The average salinity removal rates (TDS removal) in CMDC, AnAmoxMDC and NiAmoxMD…" · T=22°C, substrate=glucose, steady_stateModellierbar
Ohmic Resistance×250,1Ω95 %
electrochemical impedance spectroscopy
"EIS measurements indicated that the ohmic resistance of AnAmoxMDC was 97.3 Ω, wh…" · T=22°C, substrate=glucose, steady_stateModellierbar
Salt Removal×254,4%95 %
conductivity measurement
"The average salinity removal rates (TDS removal) in CMDC, AnAmoxMDC and NiAmoxMD…" · T=22°C, substrate=glucose, steady_stateModellierbar
Substrate Concentration×26,3mg/L95 %
colorimetric analysis
"The accumulated NO2−-N concentration at the end of the third and fourth cycles w…" · T=22°C, substrate=glucose, degradationModellierbar
Ammonium-N Removed×284,8%95 %
colorimetric analysis
"at the end of the third and fourth cycles, accumulation of nitrite was observed …" · T=22°C, substrate=glucose, degradationModellierbar
Anode Oxidation Current×2706µA95 %
cyclic voltammetry
"The results showed that NiAmoxMDC produced higher oxidation current of 706 µA co…" · T=22°C, substrate=glucose, steady_stateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Anode Oxidation Current×2254µA95 %
cyclic voltammetry
"The results showed that NiAmoxMDC produced higher oxidation current of 706 µA co…" · T=22°C, substrate=glucose, steady_stateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Anode Oxidation Current×277,7µA95 %
cyclic voltammetry
"The results showed that NiAmoxMDC produced higher oxidation current of 706 µA co…" · T=22°C, substrate=glucose, steady_stateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Salt Removal×253,9%95 %
conductivity measurement
"The average salinity removal rates (TDS removal) in CMDC, AnAmoxMDC and NiAmoxMD…" · T=22°C, substrate=glucose, steady_stateModellierbar
Ammonium-N Removed×298,3%95 %
colorimetric analysis
"The results showed that in NiAmoxMDC, nitrite was not detected and NH4+-N remova…" · T=22°C, substrate=glucose, steady_stateModellierbar
Substrate Concentration×210,3mg/L95 %
colorimetric analysis
"The accumulated NO2−-N concentration at the end of the third and fourth cycles w…" · T=22°C, substrate=glucose, degradationModellierbar
Power Density Volumetric×21.010mW/m³95 %
polarization curve
"the maximum power density produced by NiAmoxMDC (1,007 mW/m3) was higher than th…" · T=22°C, substrate=glucose, steady_stateAusgeschlossen: Verifizierer hat den Wert abgelehnt
Ohmic Resistance×297,3Ω95 %
electrochemical impedance spectroscopy
"EIS measurements indicated that the ohmic resistance of AnAmoxMDC was 97.3 Ω, wh…" · T=22°C, substrate=glucose, steady_stateModellierbar
Ammonium-N Removed×285,6%95 %
colorimetric analysis
"ammonium-nitrogen removal for the first, second, third, and fourth batch cycles …" · T=22°C, substrate=glucose, steady_stateModellierbar
Ammonium-N Removed×297,8%95 %
colorimetric analysis
"NH4+-N removal was 98.3% and 97.8% (Supplementary Table S2) at the end of first …" · T=22°C, substrate=glucose, steady_stateModellierbar
Chemical Oxygen Demand (COD) Removal×262,1%95 %
cod assay (closed-reflux)
"COD removal rates in the anode chambers of CMDC, AnAmoxMDC, and NiAmoxMDC over t…" · T=22°C, substrate=glucose, steady_stateModellierbar
Ammonium-N Removed×281,6%95 %
colorimetric analysis
"ammonium-nitrogen removal for the first, second, third, and fourth batch cycles …" · T=22°C, substrate=glucose, steady_stateModellierbar
Electrical Conductivity×217,9mS/cm95 %
conductivity measurement
"The electrical conductivity of 10 g/L of NaCl at 25 °C was 17.92 mS/Cm" · T=25°CModellierbar
Ammonium-N Removed×279,5%95 %
colorimetric analysis
"ammonium-nitrogen removal for the first, second, third, and fourth batch cycles …" · T=22°C, substrate=glucose, startupModellierbar
Power Density Volumetric×2444mW/m³95 %
polarization curve
"the maximum power density produced by NiAmoxMDC (1,007 mW/m3) was higher than th…" · T=22°C, substrate=glucose, steady_stateModellierbar
Power Density Volumetric×2952mW/m³95 %
polarization curve
"the maximum power density produced by NiAmoxMDC (1,007 mW/m3) was higher than th…" · T=22°C, substrate=glucose, steady_stateModellierbar
Ammonium-N Removed×278,6%95 %
colorimetric analysis
"the removal rate of NH4+-N was decreased to 84.8% and 78.6%" · T=22°C, substrate=glucose, degradationModellierbar
25 von 72 angezeigt

Methodik

Welches System und wie es betrieben wurde

Methodik

Methodology

Three MDC configurations (NiAmoxMDC with aerated nitritation-anammox biocathode, AnAmoxMDC with anaerobic anammox biocathode, and CMDC with abiotic air cathode) were operated in fed-batch mode for >1,100 hours with identical reactor sizes. Cathode chambers were fed 70 mg/L NH₄⁺-N (and 70 mg/L NO₂⁻-N for AnAmoxMDC) at two aeration rates (10 ml/min initially, then 3 ml/min). Anode chambers received glucose substrate. Nitrogen species (NH₄⁺-N, NO₂⁻-N, NO₃⁻-N) were measured by ion chromatography at the end of each cycle. Power density, current density, and polarization curves were recorded. Electrochemical characterization included cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Desalination performance was assessed by total dissolved solids (TDS) removal in the middle chamber.

Systemkonfiguration

FeldWert
reactor typeMDC
chamber config3-chamber

Elektrodenspezifikationen

FeldWert
cathode materialair cathode

Leistungskennzahlen

FeldWert
citation count25

Betriebsparameter

FeldWert
substrate["wastewater"]

Betriebsbedingungen

6 Läufe extrahiert
LaufT°CpHAnolytpHKatholytSubstrat[S]mg/LHRThModusR_extΩV_appVInokulum
v2-23890a68cfbc047922——glucose468.7—steady_state1000——
v2-327e11be5622afa122—————steady_state———
v2-58a2540478c500d825—————————
v2-760fcc0cb350b21c25———468.7—————
v2-e214e7fa679d1a9822——glucose468.7—degradation1000——
v2-e608a9509276d46a22——glucose468.7—startup1000——

Mikrobielle Kinetik

2 Konstanten
OrganismusSubstratParameterWertEinheitKonf.
anammox bacteria(unspecified)doubling_time11Tage100 %
anammox bacteria(unspecified)doubling_time11Tage100 %

Extraktionspipeline

Rohextraktionen, Artefakte, Qualitätssignal

Extraktionsqualität

Ehrlichkeitssignal

Bemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.

Parametervollständigkeit

50 %

Anteil der erwarteten Parameter, die extrahiert wurden

Datenvollständigkeit

60 %

Gesamtabdeckung der Extraktion über alle Felder

KI-Konfidenz

82 %

Vom Modell selbst angegebene Konfidenz

Mittlere Parameterkonfidenz

78 %

Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen

Letzte Extraktion:vpipeline-v2FULL_EXTRACTIONabgeschlossen142 Parameter angezeigt

vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

07

Quell-PDF

Die Publikation, wie sie erschienen ist.

3D-Modell wird geladen …

Repräsentatives Modell, generisches mikrobielle Entsalzungszelle

Repräsentatives Modell: mikrobielle Entsalzungszelle – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.

MDC
System
25,6Prozent
Bestes Ergebnis · Coulomb-Effizienz
bester von 6
142
Extrahierte Werte
2019
Jahr

Schlagwörter

  • Anammox
  • MOX fuel
  • Wastewater
  • Sewage treatment
  • Desalination
  • Nuclear chemistry

Zitieren

Umesh Ghimire, Veera Gnaneswar Gude (2019). Accomplishing a N-E-W (nutrient-energy-water) synergy in a bioelectrochemical nitritation-anammox process. Scientific Reports. https://doi.org/10.1038/s41598-019-45620-2

Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.

Im Labor öffnen