Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.
Publikation · MFC
The Denitrification Characteristics and Microbial Community in the Cathode of an MFC with Aerobic Denitrification at High Temperatures
Zusammenfassung
Was die Publikation berichtet, in ihren eigenen Worten.
Zusammenfassung
Microbial fuel cells (MFCs) have attracted much attention due to their ability to generate electricity while treating wastewater. The performance of a double-chamber MFC with simultaneous nitrification and denitrification (SND) in the cathode for treating synthetic high concentration ammonia wastewater was investigated at different dissolved oxygen (DO) concentrations and high temperatures. The results showed that electrode denitrification and traditional heterotrophic denitrification co-existed in the cathode chamber. Electrode denitrification by aerobic denitrification bacterium (ADB) is beneficial for achieving a higher voltage of the MFC at high DO concentrations (3.0-4.2 mg/L), while traditional heterotrophic denitrification is conducive to higher total nitrogen (TN) removal at low DO (0.5-1.0 mg/L) concentrations. Under high DO conditions, the nitrous oxide production and TN removal efficiency were higher with a 50 Ω external resistance than with a 100 Ω resistance, which demonstrated that electrode denitrification by ADB occurred in the cathode of the MFC. Sufficient electrons were inferred to be provided by the electrode to allow ADB survival at low carbon:nitrogen ratios (≤0.3). Polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) results showed that increasing the DO resulted in a change of the predominant species from thermophilic autotrophic nitrifiers and facultative heterotrophic denitrifiers at low DO concentrations to thermophilic ADB at high DO concentrations. The predominant phylum changed from Firmicutes to Proteobacteria , and the predominant class changed from Bacilli to Alpha, Beta , and Gamma Proteobacteria .
KI-Zusammenfassung
82 % KonfidenzThis study demonstrates that dissolved oxygen concentration is a critical control parameter in bioelectrochemical cathodes for simultaneous nitrification–denitrification (SND) of high-ammonia wastewater at elevated temperatures (36–48 °C). At low DO (0.5–1.0 mg/L), heterotrophic denitrifiers dominate and achieve higher total nitrogen removal (~14 mg/(L·d)) but lower voltage. At high DO (3.0–4.2 mg/L), aerobic denitrifying bacteria (ADB) become dominant, producing higher voltage (~100 mV) and N₂O emissions, with electrode-driven denitrification contributing 8.5–14.6 mg N/(L·d) depending on external resistance. Lowering external resistance from 100 Ω to 50 Ω increases electrode denitrification rate and N₂O production, revealing a trade-off between power output and nitrogen removal pathway.
Zentrale Erkenntnisse
Zielkonflikt At high DO (3.0–4.2 mg/L), electrode denitrification by ADB produces 13.5–14.6 mg N/(L·d) with 50 Ω resistance versus 8.5–9.0 mg N/(L·d) with 100 Ω, showing that lower external resistance drives higher electrode-catalyzed denitrification.
Was heißt das. Operators targeting maximum electrode-driven nitrogen removal should minimize external resistance, but this increases N₂O slip (10% of nitrogen removed becomes N₂O rather than N₂).
Zielkonflikt Heterotrophic denitrification at low DO (0.5–1.0 mg/L) removes ~14 mg TN/(L·d) total, but electrode denitrification contributes only ~7 mg/(L·d), meaning COD-driven heterotrophic pathways dominate nitrogen removal at low oxygen.
Was heißt das. If nitrogen removal is the priority and carbon is available, maintain low DO and intermittent aeration to favor heterotrophic denitrifiers over electrode denitrification, accepting lower voltage output.
Mechanismus Increasing DO from 0.5–1.0 to 3.0–4.2 mg/L shifts the dominant microbial community from Firmicutes (Ureibacillus, Bacillus, Anoxybacillus) to Proteobacteria (Aquamicrobium, Brachymonas, Comamonas), enabling aerobic denitrification but reducing total heterotrophic denitrification capacity.
Was heißt das. Design cathode aeration strategy around desired microbial community: low DO favors thermophilic heterotrophic denitrifiers; high DO selects for aerobic denitrifiers with electrode-coupling capability.
Schwellenwert N₂O production increases with temperature and is independent of electrode potential at 100 Ω resistance (0.7–1.1 mg/L N₂O across all conditions), but becomes electrode-dependent at 50 Ω resistance, with ~10% of nitrogen removed converted to N₂O.
Was heißt das. Minimize N₂O emissions by avoiding low external resistance (<50 Ω) during high-DO operation, or accept N₂O as a byproduct of efficient electrode denitrification.
Mechanismus At C/N ratio ≤0.3 (COD 300 mg/L, NH₄⁺-N 480 mg/L), electrode denitrification by ADB provides sufficient electrons to sustain nitrogen removal without heterotrophic carbon oxidation, enabling nitrogen removal independent of organic substrate availability.
Was heißt das. In high-ammonia, low-carbon wastewaters (e.g., sludge digestion liquor), electrode-driven denitrification can be the primary nitrogen removal mechanism if high DO and low external resistance are maintained.
Ansatzpunkte6
Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.
Mittel No systematic variation of external resistance between 50 and 100 Ω to map the transition point where electrode denitrification becomes the dominant pathway and N₂O production becomes electrode-dependent.
The paper tests only 50 Ω and 100 Ω; intermediate resistances (60, 70, 80, 90 Ω) would reveal the threshold for switching from heterotrophic to electrode-driven denitrification.
Versuch. Vary external resistance in 10 Ω increments from 50–100 Ω; measure electrode potential, N₂O concentration, TN removal rate, and dominant microbial species at each resistance.
Hoch No investigation of cathode potential (vs. SHE or Ag/AgCl) as an independent control variable; only external resistance is varied, which indirectly controls potential.
The paper measures anode potential (Figure 3D, 4D) but does not report cathode potential. Cathode potential directly determines which nitrogen species (NO₃⁻, NO₂⁻, N₂O, N₂) are thermodynamically favored for reduction.
Versuch. Potentiostat the cathode at fixed potentials (e.g., −0.2, −0.4, −0.6, −0.8 V vs. SHE) while maintaining high DO and measuring N₂O, NO₂⁻, and TN removal rates to identify the potential window for selective N₂O or N₂ production.
Mittel No measurement of nitrite (NO₂⁻-N) accumulation in the cathode effluent during high-DO, low-resistance operation, despite evidence that electrode denitrification is occurring.
Figure 2 shows NO₂⁻-N in the effluent but does not report its concentration during stage 4 (high DO, 50 Ω). Nitrite accumulation is a sign of incomplete denitrification and a potential environmental concern.
Versuch. Measure NO₂⁻-N, NO₃⁻-N, and N₂O simultaneously during stage 4 at 50 Ω and 100 Ω to quantify the nitrogen speciation and identify whether nitrite is being accumulated or recycled.
Mittel No exploration of catholyte pH effects on aerobic denitrification or N₂O production, despite pH being a known regulator of denitrification enzyme activity.
The paper does not report pH during stages 3–4 (high DO). Aerobic denitrification enzymes have pH optima that may differ from anaerobic denitrification, affecting N₂O yield.
Versuch. Vary catholyte pH (6.5–8.5) at high DO and 50 Ω resistance; measure N₂O production, electrode potential, and dominant ADB species to identify the pH window minimizing N₂O slip.
Niedrig No testing of lower C/N ratios (<0.3) to confirm the lower bound at which electrode denitrification can sustain ADB without heterotrophic carbon.
The paper states that ADB survive at C/N ≤0.3 but tests only one ratio (0.3). Lower ratios would test the limit of electrode-driven nitrogen removal.
Versuch. Reduce influent COD to 100–150 mg/L (C/N 0.1–0.15) while maintaining 480 mg/L NH₄⁺-N and high DO; measure TN removal rate and ADB abundance to confirm the minimum C/N for sustained denitrification.
Niedrig No comparison of electrode materials (carbon brush vs. felt, graphite, stainless steel) on ADB enrichment and N₂O production at high DO.
The paper uses only carbon brush electrodes. Different materials have different electron transfer kinetics and surface properties that may favor different ADB species or N₂O pathways.
Versuch. Replace carbon brush with carbon felt or graphite felt at identical operating conditions (high DO, 50 Ω, 36–48 °C); measure electrode potential, N₂O, TN removal, and microbial community composition.
Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen
Extrahierte Werte
Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.
n = 38 extrahierte Werte
Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.
15 von 38 extrahierten Zeilen modellierbar
- 19 nicht kanonisiert (kein kanonischer Slug)
- 3 kein SI-Wert
- 1 nicht als modellierbar markiert
| Parameter | Wert | Einheit | Konfidenz | Quelle | Anmerkungen | Modellierbar |
|---|---|---|---|---|---|---|
| Reactor Volume×2 | 0,452 | L | 95 % | design specification | "The anode and cathode chambers were both made of organic glass tube 8 cm high an…" · replicates_n=1, condition_hint=Design parameter, each chamber, electrode_material=carbon brush | Modellierbar |
| Ammonium Ion Concentration | 480 | mg/L | 95 % | design specification | "CH3COONa and NH4HCO3 were added to maintain the chemical oxygen demand (COD) and…" · substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h | Modellierbar |
| Chemical Oxygen Demand (COD) Concentration | 300 | mg/L | 95 % | design specification | "CH3COONa and NH4HCO3 were added to maintain the chemical oxygen demand (COD) and…" · substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h | Modellierbar |
| Hydraulic retention time | 10,4 | h | 95 % | design specification | "the wastewater was pumped continuously into the anode chamber with hydraulic ret…" · substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h | Modellierbar |
| Temperature | 31 ± 1 (SD) | °C | 90 % | water bath control | "The temperature was initially set to 31 ± 1◦C and then changed to a dynamic temp…" · T=31°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, startup | Modellierbar |
| Operating Temperature | 36 | °C | 85 % | water bath control | "the temperature of the reactor increased and fluctuated over the range of 36–48◦C" · T=36°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Modellierbar |
| Operating Temperature | 48 | °C | 85 % | water bath control | "the temperature of the reactor increased and fluctuated over the range of 36–48◦C" · T=48°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Modellierbar |
| Temperature | 42 ± 6 (range) | °C | 80 % | water bath control | "In stage 2 (days 6–34), the temperature of the reactor increased and fluctuated o…" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Modellierbar |
| Dissolved Oxygen Concentration Range | 1 | mg/L | 80 % | hach-hq30d do analyzer | "the DO of the catholyte was 0.5–1.0 mg/L" · T=31°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, startup | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Dissolved Oxygen Concentration Range | 0,5 | mg/L | 80 % | hach-hq30d do analyzer | "the DO of the catholyte was 0.5–1.0 mg/L" · T=31°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, startup | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Dissolved Oxygen | 3,6 ± 0,6 (SD) | mg/L | 80 % | hach-hq30d do analyzer | "In stage 3 (days 35–77), the reactor was set to continuous aeration instead of i…" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Modellierbar |
| Dissolved Oxygen Concentration Range | 4,2 | mg/L | 80 % | hach-hq30d do analyzer | "Electrode denitrification by aerobic denitrification bacterium (ADB) is beneficial …" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| C/N Ratio | 0,3 | — | 80 % | calculated from influent composition | "The influent C/N for the cathode chamber of the MFC was less than 0.3" · substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h | Ausgeschlossen: kein SI-Wert |
| Dissolved Oxygen Concentration Range | 3 | mg/L | 80 % | hach-hq30d do analyzer | "Electrode denitrification by aerobic denitrification bacterium (ADB) is beneficial …" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Voltage | 100 | mV | 75 % | voltage monitoring with pci1717 voltage collector | "In stage 3, the release voltage initially increased, then dropped and finally st…" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Modellierbar |
| Dissolved Oxygen (DO) Fluctuation Amplitude | 1,5 | mg/L | 75 % | hach-hq30d do analyzer | "With a 100 Ω resistance, the DO and N2O fluctuation amplitudes were 1.5 mg/L and …" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| N2O Fluctuation Amplitude | 0,3 | mg/L | 75 % | n2o microsensor analysis | "With a 100 Ω resistance, the DO and N2O fluctuation amplitudes were 1.5 mg/L and …" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| N2O Concentration | 0,7 | mg/L | 70 % | n2o microsensor analysis | "The concentrations of N2O were similar in both scenarios (0.7–1.1 mg/L)" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| N2O Concentration | 1,1 | mg/L | 70 % | n2o microsensor analysis | "The concentrations of N2O were similar in both scenarios (0.7–1.1 mg/L)" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Nitrogen Gas Conversion Percentage | 90 | % | 70 % | calculated from n2o and nitrogen gas measurements | "in which approximately 10% of the nitrogen removed was converted to N2O and 90% …" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| N2O Conversion Percentage | 10 | % | 70 % | calculated from n2o and nitrogen gas measurements | "in which approximately 10% of the nitrogen removed was converted to N2O and 90% …" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Nitrite Concentration in Cathode Effluent | 30 | mg/L | 70 % | standard methods for the examination of water and wastewater | "the NO−2 -N concentration decreased to approximately 30 mg/L." · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Nitrogen Removal | 7 ± 0,5 (range) | mg/(L·d) | 70 % | nitrogen balance from influent/effluent analysis | "The TN removal by electrode denitrification was 8.5–9.0 mg/(L·d), which represent…" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: kein SI-Wert |
| N2O Production | 0,9 ± 0,2 (range) | mg/L | 70 % | n2o microsensor analysis | "The concentrations of N2O were similar in both scenarios (0.7–1.1 mg/L), whereas…" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Ausgeschlossen: nicht kanonisiert (kein kanonischer Slug) |
| Dissolved Oxygen | 0,75 | mg/L | 70 % | hach-hq30d do analyzer | "the concentrations of DO with a 100 Ω resistance were 0.7–1.0 mg/L" · T=42°C, substrate=synthetic wastewater with acetate and ammonia, HRT=10.4h, steady_state | Modellierbar |
Methodik
Welches System und wie es betrieben wurde
Methodik
Methodology
A double-chamber MFC with carbon brush electrodes and Nafion 117 proton exchange membrane was operated in four stages with varying DO (0.5–1.0 and 3.0–4.2 mg/L), external resistance (50 and 100 Ω), and temperature (31–48 °C). Synthetic wastewater containing 300 mg/L COD and 480 mg/L NH₄⁺-N was fed to the anode at 10.4 h HRT. Cathode effluent was analyzed for NH₄⁺-N, NO₂⁻-N, NO₃⁻-N, and N₂O; microbial community was characterized by PCR-DGGE on days 27 and 83. Electrode potential and voltage were continuously monitored; oxygen reduction and denitrification rates were calculated using Coulomb's law.
Systemkonfiguration
| Feld | Wert |
|---|---|
| reactor type | MFC |
| chamber config | 2-chamber |
Betriebsbedingungen
8 Läufe extrahiert| Lauf | T°C | pHAnolyt | pHKatholyt | Substrat | [S]mg/L | HRTh | Modus | R_extΩ | V_appV | Inokulum |
|---|---|---|---|---|---|---|---|---|---|---|
| v2-10e05b06bdee899a | 48 | — | — | synthetic wastewater with acetate and ammonia | — | 10.4 | steady_state | 100 | — | — |
| v2-2e71d878df5703ed | 42 | — | — | synthetic wastewater with acetate and ammonia | — | 10.4 | steady_state | 100 | — | — |
| v2-795376371898ad7a | 42 | — | — | synthetic wastewater with acetate and ammonia | — | 10.4 | steady_state | 50 | — | — |
| v2-7c0fa617cf749a20 | — | — | — | synthetic wastewater with acetate and ammonia | 480 | 10.4 | — | — | — | — |
| v2-d25a36e371278a61 | 31 | — | — | synthetic wastewater with acetate and ammonia | — | 10.4 | startup | 100 | — | — |
| v2-e1259c9f70791f34 | 36 | — | — | synthetic wastewater with acetate and ammonia | — | 10.4 | steady_state | 100 | — | — |
| v2-f06fb671f249ca00 | 42 | — | — | synthetic wastewater with acetate and ammonia | — | 10.4 | steady_state | — | — | — |
| v2-f33486d127f6738f | — | — | — | synthetic wastewater with acetate and ammonia | — | 10.4 | — | — | — | — |
Extraktionspipeline
Rohextraktionen, Artefakte, Qualitätssignal
Extraktionsqualität
EhrlichkeitssignalBemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.
KI-Konfidenz
82 %
Vom Modell selbst angegebene Konfidenz
Mittlere Parameterkonfidenz
76 %
Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen
vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1
Diagramm-Explorer
Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.
Modell erkunden
Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.
KI-Erkenntnisse
Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.
Ähnliche Publikationen vergleichen
Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.
Quell-PDF
Die Publikation, wie sie erschienen ist.
Repräsentatives Modell, generisches MFC
Zum Interagieren tippenRepräsentatives Modell, generisches MFC
Repräsentatives Modell: MFC – zugeordnet nur anhand des Systemtyps der Publikation, nicht ihres Reaktors oder ihrer Geometrie.
Schlagwörter
- Denitrification
- Aerobic denitrification
- Microbial fuel cell
- Heterotroph
- Environmental chemistry
- Denitrifying bacteria
Zitieren
Jianqiang Zhao, Jinna Wu, Xiaoling Li et al. (2017). The Denitrification Characteristics and Microbial Community in the Cathode of an MFC with Aerobic Denitrification at High Temperatures. Frontiers in Microbiology. https://doi.org/10.3389/fmicb.2017.00009
- PubMed
- 28154554
- Zeitschrift
- Frontiers in Microbiology
Öffnen Sie das Modell im Labor, um alle Steuerelemente, die Parameterbearbeitung und Vorlagen-Overlays zu nutzen.
Im Labor öffnen