Forschungsdaten – Titel und Zusammenfassungen von Publikationen, extrahierte Daten und Katalogeinträge – erscheinen in ihrer Originalsprache Englisch.

Forschung

Publikation

A tartrate-EDTA-Fe complex mediates electron transfer and enhances ammonia recovery in a bioelectrochemical-stripping system

01

Zusammenfassung

Was die Publikation berichtet, in ihren eigenen Worten.

KI-angereichert· 82 %

Zusammenfassung

Traditional bioelectrochemical systems (BESs) coupled with stripping units for ammonia recovery suffer from an insufficient supply of electron acceptors due to the low solubility of oxygen. In this study, we proposed a novel strategy to efficiently transport the oxidizing equivalent provided at the stripping unit to the cathode by introducing a highly soluble electron mediator (EM) into the catholyte. To validate this strategy, we developed a new kind of iron complex system (tartrate-EDTA-Fe) as the EM. EDTA-Fe contributed to the redox property with a midpoint potential of -0.075 V (vs. standard hydrogen electrode, SHE) at pH 10, whereas tartrate acted as a stabilizer to avoid iron precipitation under alkaline conditions. At a ratio of the catholyte recirculation rate to the anolyte flow rate (R C-A ) of 12, the NH 4 + -N recovery rate in the system with 50 mM tartrate-EDTA-Fe complex reached 6.9 ± 0.2 g N m -2 d -1 , approximately 3.8 times higher than that in the non-EM control. With the help of the complex, our system showed an NH 4 + -N recovery performance comparable to that previously reported but with an extremely low R C-A (0.5 vs. 288). The strategy proposed here may guide the future of ammonia recovery BES scale-up because the introduction of an EM allows aeration to be performed only at the stripping unit instead of at every cathode, which is beneficial for the system design due to its simplicity and reliability.

KI-Zusammenfassung

82 % Konfidenz

This study demonstrates that a tartrate-EDTA-Fe(III/II) electron mediator (EM) in the catholyte of a bioelectrochemical ammonia recovery system dramatically improves performance by providing a highly soluble oxidizing equivalent (50 mM) instead of relying on dissolved oxygen (~7 mg/L). At pH 10 and RC-A = 12, the EM system achieved 6.9 ± 0.2 g NH4+-N m−2 d−1 recovery—3.8× higher than the non-EM control—while enabling operation at RC-A = 0.5 with comparable performance to prior work using RC-A = 288. The tartrate stabilizes the iron complex under alkaline conditions, and the midpoint potential (−0.075 V vs. SHE at pH 10) enables efficient cathode reduction with minimal overpotential.

Zentrale Erkenntnisse

  • Schwellenwert Tartrate-EDTA-Fe complex requires a tartrate:EDTA-Fe molar ratio ≥0.33 to prevent iron precipitation; at 1:1 ratio, total dissolved Fe remained stable at ~50 mM over 140 h at pH 10, whereas at 0.2:1 it dropped to 42.64 ± 0.45 mM.

    Was heißt das. Operators must maintain tartrate:EDTA-Fe ≥1:1 molar ratio in alkaline catholytes to prevent loss of redox capacity and maintain stable mediator concentration.

  • Mechanismus The EM system (SEM-1A) achieved 1.20 ± 0.02 A m⁻² stable current density, 36% higher than the oxygen-limited non-EM system with dual aeration (SNonEM-2A: 0.883 ± 0.004 A m⁻²), despite both having sufficient electron acceptor supply.

    Was heißt das. Tartrate-EDTA-Fe(III) reduction kinetics are superior to oxygen reduction on unmodified carbon electrodes; use EM when catalyst-free electrodes are preferred or when kinetic advantage is needed.

  • Zielkonflikt Oxidizing equivalent supply rate in SEM-1A (579 C h⁻¹) was 50× higher than SNonEM-1A (10.28 C h⁻¹), yet consumption was only 41.4 C h⁻¹, indicating RC-A can be reduced from 12 to 0.5 while maintaining comparable NH4+-N recovery (6.9 vs. prior work at 288).

    Was heißt das. Reduce catholyte recirculation rate dramatically (24-fold lower) when using EM, cutting pumping energy and stripping gas flow while maintaining recovery rate—critical for scale-up economics.

  • Mechanismus NH4+-N recovery efficiency (removed vs. recovered) was 85–91% across all modes; the gap was attributed to microbial assimilation at the bioanode rather than stripping losses.

    Was heißt das. Design anode chambers to minimize heterotrophic assimilation (e.g., via selective enrichment or anode potential control) to close the 9–15% gap and improve overall N recovery.

  • Schwellenwert At RC-A = 0.5, SEM-1A current density dropped to ~0.6 A m⁻² and NH4+-N recovery rate fell to ~3.5 g N m⁻² d⁻¹, indicating a lower operating window threshold below which mediator regeneration becomes rate-limiting.

    Was heißt das. Operators should not reduce RC-A below 0.5–1.0 without accepting proportional loss in recovery rate; balance recirculation cost against performance target.

Ansatzpunkte6

Konkrete Lücken in dieser Publikation, jeweils mit einem Experiment, das sie schließen würde.

  • Hoch No investigation of N2O or NO2− accumulation during operation; nitrogen speciation in anode and cathode chambers not reported.

    Paper focuses on ammonia recovery but does not measure whether denitrification or nitrification intermediates form, which is critical for understanding N-balance and potential emissions.

    Versuch. Measure NO3−, NO2−, N2O, and N2 in anode and cathode chambers across RC-A range 0.5–12 and current densities 0.6–1.2 A m⁻² using ion chromatography and gas chromatography.

  • Mittel Cathode potential was not systematically varied; only one cathode potential (−0.2 V vs. SHE) used in chronoamperometry test.

    Section 3.1 shows CV redox peaks at −0.157 V (reduction) and −0.007 V (oxidation); operating window and trade-offs between potential and current/recovery rate not explored.

    Versuch. Vary cathode potential from −0.3 to +0.1 V vs. SHE at fixed RC-A and measure current density, NH4+-N recovery rate, and mediator oxidation state to map operating window.

  • Mittel Dissolved oxygen concentration in catholyte not measured during steady-state operation in SEM-1A; only reported for SNonEM-1A (~7.1 mg/L).

    Section 3.2.1 states DO was 'saturated (~7.1 mg L⁻¹)' in SNonEM-1A but no DO data given for SEM-1A, making it unclear whether residual O2 contributes to mediator regeneration.

    Versuch. Measure DO continuously in SEM-1A catholyte outlet and in stripping column inlet/outlet across RC-A 0.5–12 to quantify O2 contribution to Fe(II) reoxidation.

  • Mittel No variation of EM concentration; only 50 mM tartrate-EDTA-Fe tested in main experiments.

    Section 3.1 tested tartrate:EDTA-Fe ratios but not absolute EM concentration; optimal concentration for cost–performance trade-off not determined.

    Versuch. Test 10, 25, 50, 100 mM tartrate-EDTA-Fe at RC-A 1–12 and measure NH4+-N recovery rate, current density, and mediator stability to identify concentration threshold.

  • Mittel Anode chamber microbial community and acetate oxidation kinetics not characterized; 9–15% gap between removed and recovered NH4+-N attributed to assimilation but not verified.

    Section 3.2.2 states TAN remained stable and gap was 'likely due to microbial assimilation' but no biomass, enzyme activity, or 13C-acetate tracing provided.

    Versuch. Measure anode biofilm biomass, acetate consumption rate, and heterotrophic growth rate; use 13C-labeled acetate to quantify assimilation vs. oxidation.

  • Niedrig No long-term stability test (>7 days) of tartrate-EDTA-Fe in operating BES; only 140 h static stability and 67 h chronoamperometry shown.

    Section 3.1 and Fig. S2 show short-term stability but operational stability over weeks/months not demonstrated; iron leakage into anode chamber via CEM not measured.

    Versuch. Operate SEM-1A for 30 days at RC-A 1–6; measure dissolved Fe in anode chamber weekly and track current density and recovery rate to assess mediator loss and CEM permeability.

Erstellt von der MESSAI-Extraktionspipeline · mit dem Quell-PDF abgleichen

02

Extrahierte Werte

Jeder aus der Publikation entnommene Wert mit seiner Quelle, damit sich jede Zahl am Text prüfen lässt.

n = 26 extrahierte Werte

Wählen Sie eine Quellenangabe, um Zitat, Seite und Konfidenz hinter einem Wert zu sehen.

10 von 26 extrahierten Zeilen modellierbar

  • 7 nicht kanonisiert (kein kanonischer Slug)
  • 9 kein SI-Wert
ParameterWertEinheitKonfidenzQuelleAnmerkungenModellierbar
Current Density1,2A m⁻²90 %
extrahiert
"the current density initially increased to approximately 1.5 A m2, then graduall…" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateModellierbar
Current Density0,27A m⁻²90 %
extrahiert
"the variations in the currents in all the BESs followed a similar trend, gradual…" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateModellierbar
Current Density0,883A m⁻²90 %
extrahiert
"When another aeration point was added to the cathode chamber (SNonEM-2A), an obv…" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateModellierbar
pH in catholyte10—90 %
extrahiert
"that of the pH in the catholyte also increased rapidly and then remained stable,…" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
NH4+-N removal rate7,6g N m⁻² d⁻¹90 %
extrahiert
"NH4+-N removal rate in SEM-1A was 7.6 ± 0.2 g N m2 d1" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: kein SI-Wert
Total ammonia nitrogen in catholyte225mg L⁻¹90 %
extrahiert
"for the different cathode operation modes, the TAN concentration increased in th…" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Supply rate of oxidizing equivalent10,3C h⁻¹90 %
extrahiert
"We also calculated the supply rate of the oxidizing equivalent in SNonEM-1A to b…" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
NH4+-N recovery efficiency90,8%90 %
extrahiert
"the NH4+-N recovery rate was 6.9 ± 0.2 g N m2 d1 with N recovery efficiency of 90…" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
NH4+-N removal rate6,2g N m⁻² d⁻¹90 %
extrahiert
"NH4+-N removal rate in SNonEM-2A was 6.2 ± 0.1 (Table 2)" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: kein SI-Wert
Ammonium Recovery3,7g N m⁻² d⁻¹90 %
extrahiert
"the variations in the NH4+-N recovery rates followed a similar trend as the curr…" · substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: kein SI-Wert
Ammonium Recovery5,4g N m⁻² d⁻¹90 %
extrahiert
"Fig. 7b illustrates the supply rates and consumption rates of the oxidizing equi…" · substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: kein SI-Wert
NH4+-N recovery efficiency85%90 %
extrahiert
"N recovery efficiency in SNonEM-1A was 85.0 ± 2.3%" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Supply rate of oxidizing equivalent579C h⁻¹90 %
extrahiert
"the introduction of tartrate-EDTA-Fe complex overcame the limitation in the oxid…" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
Ammonium Recovery5,4g N m⁻² d⁻¹90 %
extrahiert
"the NH4+-N recovery rate obtained in SNonEM-2A (with a sufficient oxygen supply, …" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: kein SI-Wert
NH4+-N recovery efficiency88,1%90 %
extrahiert
"N recovery efficiency in SNonEM-2A was 88.1 ± 3.4%" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: nicht kanonisiert (kein kanonischer Slug)
NH4+-N removal rate2,1g N m⁻² d⁻¹90 %
extrahiert
"NH4+-N removal rate in SNonEM-1A shown in Table 2 was 2.1 ± 0.2" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: kein SI-Wert
Ammonium Ion Concentration367mg L⁻¹90 %
extrahiert
"Effluent NH4+-N in SNonEM-1A was 367.29 ± 6.15 mg L-1" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateModellierbar
Cathode Potential-0,103V vs. SHE90 %
extrahiert
"For SNonEM-2A, the cathode working potential was measured to be 0.103 ± 0.020 V" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateModellierbar
Ammonium Ion Concentration205mg L⁻¹90 %
extrahiert
"Effluent NH4+-N in SNonEM-2A was 205.45 ± 2.66 mg L-1" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateModellierbar
Cathode Potential-0,053V vs. SHE90 %
extrahiert
"the cathode working potential in SEM-1A was 0.053 ± 0.020 V more positive than t…" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateModellierbar
Ammonium-N Removed66,9%90 %
extrahiert
"a much higher NH4+-N removal efficiency was achieved in SEM-1A than in SNonEM-1A …" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateModellierbar
Ammonium-N Removed54,5%90 %
extrahiert
"N removal efficiency in SNonEM-2A was 54.5 ± 0.7% (Table 2)" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateModellierbar
Ammonium-N Removed18,5%90 %
extrahiert
"NH4+-N removal efficiency was achieved in SEM-1A than in SNonEM-1A (66.9 ± 1.4% v…" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateModellierbar
Ammonium Recovery4,2g N m⁻² d⁻¹90 %
extrahiert
"the NH4+-N recovery rate of SEM-1A at an extremely low RC-A (4.2 ± 0.1 g N m-2 d…" · substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: kein SI-Wert
Ammonium Recovery1,8g N m⁻² d⁻¹90 %
extrahiert
"the NH4+-N recovery rate in SNonEM-1A system (1.8 ± 0.1 g N m2 d1)" · pH(an)=9.5, substrate=synthetic ammonium wastewater, HRT=12h, steady_stateAusgeschlossen: kein SI-Wert
25 von 26 angezeigt

Methodik

Welches System und wie es betrieben wurde

Methodik

Methodology

Two-chamber BES (120 mL anode, 180 mL cathode) with four carbon brushes per electrode, separated by cation exchange membrane, coupled to a stripping column (0.3 m packing height, pall rings) and absorption bottle (0.5 M H2SO4). Synthetic wastewater (50 mM PBS, 1700 mg/L acetate, 450 mg/L NH4+-N) fed to anode at 10 mL/h; catholyte (50 mM NaCl or 50 mM tartrate-EDTA-Fe) recirculated between cathode and stripping column at variable RC-A (0.5–12). Cyclic voltammetry (pH 7 and 10, 5 mV/s scan rate) characterized mediator redox behavior; chronoamperometry (−0.2 V vs. SHE) tested Fe(III) reduction and reoxidation kinetics. Ammonia nitrogen measured by Nessler reagent colorimetry; dissolved Fe by ICP-OES; dissolved oxygen by portable meter.

Systemkonfiguration

FeldWert
reactor typeBES
chamber config2-chamber

Betriebsbedingungen

2 Läufe extrahiert
LaufT°CpHAnolytpHKatholytSubstrat[S]mg/LHRThModusR_extΩV_appVInokulum
v2-d1d7a85467741a1c—9.5—synthetic ammonium wastewater—12steady_state10——
v2-ee2d0140b4ae8fea———synthetic ammonium wastewater—12steady_state10——

Ergebnisse

Was gemessen wurde und was funktioniert hat

Elektrochemie

1 Konstante
ElektrodeReaktionParameterWertEinheitKonf.
unknown—midpoint_potential-0.075V (vs. standard hydrogen electrode, SHE) at pH 1090 %

Extraktionspipeline

Rohextraktionen, Artefakte, Qualitätssignal

Extraktionsqualität

Ehrlichkeitssignal

Bemessen Sie Ihr Vertrauen in die extrahierten Inhalte an diesen Signalen – so hat die Pipeline ihre eigene Ausgabe für diese Publikation bewertet.

KI-Konfidenz

82 %

Vom Modell selbst angegebene Konfidenz

Mittlere Parameterkonfidenz

90 %

Durchschnittliche Konfidenz der oben angezeigten PaperParameter-Zeilen

vor dem Zitieren mit dem Quell-PDF abgleichen · Werte 0–1

03

Diagramm-Explorer

Verändern Sie die Eingaben dieser Publikation und sehen Sie, wie sich das vorhergesagte Ergebnis verschiebt.

04

Modell erkunden

Der Reaktor in 3D, mit Strömung, die sich ein- und ausschalten lässt.

05

KI-Erkenntnisse

Widersprüche, Lücken und Chancen aus dem Vergleich dieser Publikation mit dem Korpus.

06

Ähnliche Publikationen vergleichen

Die nächsten Publikationen nach System, Materialien und Organismen, mit ihren Ergebnissen nebeneinander.

07

Quell-PDF

Die Publikation, wie sie erschienen ist.

Dieser Publikation ist noch kein 3D-Modell zugeordnet. Die daraus extrahierten Werte stehen unter „Extrahierte Werte“.

1,20Ampere pro Quadratmeter
Bestes Ergebnis · Stromdichte
bester von 3
26
Extrahierte Werte
2022
Jahr

Schlagwörter

  • Stripping (fiber)
  • Ammonia
  • Oxidizing agent
  • Tartrate
  • Cathode
  • Inorganic chemistry

Zitieren

Dexin Zhang, Siyuan Zhai, Ran Zeng et al. (2022). A tartrate-EDTA-Fe complex mediates electron transfer and enhances ammonia recovery in a bioelectrochemical-stripping system. Environmental Science and Ecotechnology. https://doi.org/10.1016/j.ese.2022.100186

PubMed
36158760